Handlebar Bag Stand-Off?
#26
Junior Member
Thread Starter
Join Date: Sep 2015
Location: St. Louis, Missouri
Posts: 157
Bikes: Trek Émonda SL 5, Trek Checkpoint SL 5, Giant Trance X 2, Trek Farley
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 83 Post(s)
Liked 97 Times
in
53 Posts
This is what I came up with. There's a good 2 inches / 8 cm of clearance over the tire, and nothing rubs. It's ugly, but should do the trick.
Likes For UnCruel:
#27
Senior Member
And no matter what you think of the aesthetics, it's unseen under your tent and out of sight. You don't need to put the tent bag in a plastic bag or something? Or is the msr bag waterproof?
Likes For djb:
#28
Junior Member
Thread Starter
Join Date: Sep 2015
Location: St. Louis, Missouri
Posts: 157
Bikes: Trek Émonda SL 5, Trek Checkpoint SL 5, Giant Trance X 2, Trek Farley
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 83 Post(s)
Liked 97 Times
in
53 Posts
Damn good job, and ugly it ain't. It's actually fairly elegant looking and you did a nice even job of bending the aluminium tubes equally .Nice touch with the clear tubing to stop scratching/rubbing.
And no matter what you think of the aesthetics, it's unseen under your tent and out of sight. You don't need to put the tent bag in a plastic bag or something? Or is the msr bag waterproof?
And no matter what you think of the aesthetics, it's unseen under your tent and out of sight. You don't need to put the tent bag in a plastic bag or something? Or is the msr bag waterproof?
#29
Senior Member
handy, I kind of figured it would be if it is designed to go right onto bars.
I would watch for pressure point / rubbing spots where the two rods touch the bag, just because they are quite narrow, so "could" abraid the bag material over thousands of cycles of perhaps friction type movement. If you have concerns, you can easily put some sort of something between the two rods and the bag where you see rubbing occurs.
A small piece of foam, whatever is light and would do the job. Again, it would be out of sight under the bag. Foam doesnt absorb water and is perfect for vibrations.
Improvisation is an important thing in bike touring, and you've shown you can already think up of things and make them.
Have a fun trip when you go.
I would watch for pressure point / rubbing spots where the two rods touch the bag, just because they are quite narrow, so "could" abraid the bag material over thousands of cycles of perhaps friction type movement. If you have concerns, you can easily put some sort of something between the two rods and the bag where you see rubbing occurs.
A small piece of foam, whatever is light and would do the job. Again, it would be out of sight under the bag. Foam doesnt absorb water and is perfect for vibrations.
Improvisation is an important thing in bike touring, and you've shown you can already think up of things and make them.
Have a fun trip when you go.
#30
Senior Member
#31
Senior Member
Join Date: Aug 2010
Location: Madison, WI
Posts: 11,255
Bikes: 1961 Ideor, 1966 Perfekt 3 Speed AB Hub, 1994 Bridgestone MB-6, 2006 Airnimal Joey, 2009 Thorn Sherpa, 2013 Thorn Nomad MkII, 2015 VO Pass Hunter, 2017 Lynskey Backroad, 2017 Raleigh Gran Prix, 1980s Bianchi Mixte on a trainer. Others are now gone.
Mentioned: 48 Post(s)
Tagged: 0 Thread(s)
Quoted: 3481 Post(s)
Liked 1,478 Times
in
1,154 Posts
You might need to bend the bottom segments out wider if your load is not perfectly balanced for weight in the center, but that is something you could do on a trip if needed.
Very nice.
If it bounces on bumps, you might need to run a strap to the back side of the steerer tube to hold the tent from moving forward. I suggest you bring a strap or piece of cord that it a couple feet long on your trip, just in case it is needed.
You deserve the award for best DIY project for the year for this forum, but unfortunately no such award exists.
#32
Senior Member
oh, perhaps think about putting some layers of electric tape or whatever on the bars under the top curve of the tubes, in case even with the tubing it rubs off some of the black paint on the bars. Easy insurance.
#33
Junior Member
Thread Starter
Join Date: Sep 2015
Location: St. Louis, Missouri
Posts: 157
Bikes: Trek Émonda SL 5, Trek Checkpoint SL 5, Giant Trance X 2, Trek Farley
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 83 Post(s)
Liked 97 Times
in
53 Posts
An update, for anyone who is curious. The hanger (and the tent/bag) survived the trip, which turned out to be 6 days of mostly gravel. The hanger deformed a little, but did its job of keeping the bag off of the tire. One of the J hooks relaxed, or unbent a little. Also, the part that hangs over the handlebar bent more and tightened around the handlebar, so it had to be unbent a little to remove it from the bike. The conclusion is that this aluminum is too soft for the purpose. However, when I formed the hanger I had heated the aluminum to bend it more easily without cracking, and I suppose that might have annealed it to make it softer (what little I know about metallurgy is for metals other than aluminum).
#34
Senior Member
Join Date: Aug 2010
Location: Madison, WI
Posts: 11,255
Bikes: 1961 Ideor, 1966 Perfekt 3 Speed AB Hub, 1994 Bridgestone MB-6, 2006 Airnimal Joey, 2009 Thorn Sherpa, 2013 Thorn Nomad MkII, 2015 VO Pass Hunter, 2017 Lynskey Backroad, 2017 Raleigh Gran Prix, 1980s Bianchi Mixte on a trainer. Others are now gone.
Mentioned: 48 Post(s)
Tagged: 0 Thread(s)
Quoted: 3481 Post(s)
Liked 1,478 Times
in
1,154 Posts
An update, for anyone who is curious. The hanger (and the tent/bag) survived the trip, which turned out to be 6 days of mostly gravel. The hanger deformed a little, but did its job of keeping the bag off of the tire. One of the J hooks relaxed, or unbent a little. Also, the part that hangs over the handlebar bent more and tightened around the handlebar, so it had to be unbent a little to remove it from the bike. The conclusion is that this aluminum is too soft for the purpose. However, when I formed the hanger I had heated the aluminum to bend it more easily without cracking, and I suppose that might have annealed it to make it softer (what little I know about metallurgy is for metals other than aluminum).
The one I made which is in a prior post was 5/16 diameter. I did not heat it. The most I have had on it was roughly 5 pounds.
#37
Junior Member
Thread Starter
Join Date: Sep 2015
Location: St. Louis, Missouri
Posts: 157
Bikes: Trek Émonda SL 5, Trek Checkpoint SL 5, Giant Trance X 2, Trek Farley
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 83 Post(s)
Liked 97 Times
in
53 Posts
No, FedEx lost it. I suspect it would not be better, because without support underneath, I suspect the bag will eventually sag to the point where it makes contact with the tire, no matter how far forward it is held. That's only a supposition, however, since I didn't receive it to test.
#38
Senior Member
Oh well. I'm sure you'll come up with something simple that will work.
Hope you enjoyed the tent
Hope you enjoyed the tent
#39
Senior Member
An update, for anyone who is curious. The hanger (and the tent/bag) survived the trip, which turned out to be 6 days of mostly gravel. The hanger deformed a little, but did its job of keeping the bag off of the tire. One of the J hooks relaxed, or unbent a little. Also, the part that hangs over the handlebar bent more and tightened around the handlebar, so it had to be unbent a little to remove it from the bike. The conclusion is that this aluminum is too soft for the purpose. However, when I formed the hanger I had heated the aluminum to bend it more easily without cracking, and I suppose that might have annealed it to make it softer (what little I know about metallurgy is for metals other than aluminum).
i used the oldfangled style bar bags that used a steel rod support, with bungee cords down to hooks at the dropouts, for years. carried 5-8 pounds, including SLR camera with 200mm lens, with no issues.
switch material should solve your problem.
#40
Senior Member
handlebar bar hanger supports are typically made of steel rod.
i used the oldfangled style bar bags that used a steel rod support, with bungee cords down to hooks at the dropouts, for years. carried 5-8 pounds, including SLR camera with 200mm lens, with no issues.
switch material should solve your problem.
i used the oldfangled style bar bags that used a steel rod support, with bungee cords down to hooks at the dropouts, for years. carried 5-8 pounds, including SLR camera with 200mm lens, with no issues.
switch material should solve your problem.
#41
Senior Member
Join Date: Aug 2010
Location: Madison, WI
Posts: 11,255
Bikes: 1961 Ideor, 1966 Perfekt 3 Speed AB Hub, 1994 Bridgestone MB-6, 2006 Airnimal Joey, 2009 Thorn Sherpa, 2013 Thorn Nomad MkII, 2015 VO Pass Hunter, 2017 Lynskey Backroad, 2017 Raleigh Gran Prix, 1980s Bianchi Mixte on a trainer. Others are now gone.
Mentioned: 48 Post(s)
Tagged: 0 Thread(s)
Quoted: 3481 Post(s)
Liked 1,478 Times
in
1,154 Posts
handlebar bar hanger supports are typically made of steel rod.
i used the oldfangled style bar bags that used a steel rod support, with bungee cords down to hooks at the dropouts, for years. carried 5-8 pounds, including SLR camera with 200mm lens, with no issues.
switch material should solve your problem.
i used the oldfangled style bar bags that used a steel rod support, with bungee cords down to hooks at the dropouts, for years. carried 5-8 pounds, including SLR camera with 200mm lens, with no issues.
switch material should solve your problem.
Photo below was the bar bag that I used the steel DIY bracket on. But I was using a digital camara for this photo, one of those new inventions, high end camera with 3 megapixel resolution. Photo from 2010.
That FrontRoller pannier looks very clean, that might have been the first trip it was used on.