Chainstay replacement....who does it?
#1
Senior Member
Thread Starter
Chainstay replacement....who does it?
Wondering who would be best to contact for a chainstay replacement. While I can build bikes, I'm not sure I'm up for that kind of repair and wondering who to refer someone too.
Can anyone pass along a few names?
Thanks a lot!
Brandon
Can anyone pass along a few names?
Thanks a lot!
Brandon
#2
Full Member
While I don't have recommendations out west, knowing the material and method of construction of the frame would probably be useful information to those who do have recommendations.
#3
Senior Member
Join Date: Dec 2011
Location: NE Ohio
Posts: 2,595
Bikes: 1992 Serotta Colorado II,Co-Motion Speedster, Giant Escape Hybrid, 1977 Schwinn Super Le Tour
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 455 Post(s)
Likes: 0
Liked 112 Times
in
85 Posts
I had Franklin Frame replace mine on my touring bike. They did a great job!
#4
Senior Member
Thread Starter
#5
Senior Member
Join Date: Oct 2014
Location: Portland, OR
Posts: 12,909
Bikes: (2) ti TiCycles, 2007 w/ triple and 2011 fixed, 1979 Peter Mooney, ~1983 Trek 420 now fixed and ~1973 Raleigh Carlton Competition gravel grinder
Mentioned: 129 Post(s)
Tagged: 0 Thread(s)
Quoted: 4806 Post(s)
Liked 3,932 Times
in
2,557 Posts
TiCycles in Portland can do it. There probably isn't a repair they haven't seen. It won't be cheap but it will be done right. (They have good paint connections too.)
#6
Randomhead
Join Date: Aug 2008
Location: Happy Valley, Pennsylvania
Posts: 24,402
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
Liked 3,700 Times
in
2,520 Posts
Shipping to Franklin might not be much more than shipping to Portland. I'm sure there are builders in California that will do this too.
If it's your bike and lugged steel, i don't see why you wouldn't do it yourself.
If it's your bike and lugged steel, i don't see why you wouldn't do it yourself.
#7
framebuilder
Brandon, I agree with unterhausen that this would be a good job for you to do yourself. The advantage you have is that you can work slowly and carefully to get it right. I don't know what kind of frame building equipment you acquired during your building journey? All you really need is a carefully trued and dished rear wheel, a straight edge with a movable pointer and an adjustable T tool that can hold the rear dropouts to the seat binder bolt (after brazing the dropouts to the chain stays). I can explain the process if you want to go this route.
#8
Senior Member
Joining the chorus, do it yourself. I have only built a handful of frames, but have replaced 2 chain stays. Replacement is relatively easy compared to building a whole frame.
#9
Senior Member
Thread Starter
Thanks guys. If it were my bike then I'd certainly take it on as I'd only have myself to disappoint if something went awry, however it isn't mine so I don't know if I'd be up for it. Even though I love a challenge, I'm not sure I'd want to go there just yet.
#10
Old fart
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,792
Bikes: Several, mostly not name brands.
Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3591 Post(s)
Liked 3,401 Times
in
1,935 Posts
Chainstay replacement is probably the safest repair you can do. Reynolds told us (Trek) that chainstay replacement was the only frame repair they felt could be done with their heat-treated 753 tubing.
#12
Randomhead
Join Date: Aug 2008
Location: Happy Valley, Pennsylvania
Posts: 24,402
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
Liked 3,700 Times
in
2,520 Posts
If this is a bicycle that doesn't belong to a family member or a really close friend, I wouldn't do it either.
I have full confidence in _my_ work, but once you do something like that you own every mistake the original builder made.
I have full confidence in _my_ work, but once you do something like that you own every mistake the original builder made.
#13
Senior Member
Thread Starter
This is exactly why I'm looking for references. Thanks.
Likes For BigPoser:
#14
framebuilder
Maybe you can find a builder that will let you watch and do some of the grunt work as they do the surgery? There is always more to learn even doing something as routine as replacing chain stays. Maybe they have a tool or method that might be different or new to you.