Wheel restoration Old Spokes or New?
#1
Full Member
Thread Starter
Join Date: Dec 2020
Location: Minnesota
Posts: 305
Bikes: a few
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 92 Post(s)
Liked 379 Times
in
144 Posts
Wheel restoration Old Spokes or New?
Working on bringing back to life my 1981 Univega Specialissima Wheel Set. The Araya wheels are true and straight, but the spokes have some rust and are crusty. Looking for advice on replacing the spokes or cleaning them up? For now it is just a labor of love trying to bring this back to it's former glory. Original SunShine Gyromaster hubs should clean up nicely.
Thoughts?
Thoughts?
#2
Senior Member
Join Date: Jun 2006
Posts: 20,305
Mentioned: 130 Post(s)
Tagged: 0 Thread(s)
Quoted: 3464 Post(s)
Liked 2,829 Times
in
1,995 Posts
Replace- the plating is very thin. You Could clean them up and just set yourself up for future fast deterioration.
with the labor involved, but fresh.
and note the lengths, spokes should fill the nipple and not extend, drive side should be 1-2 mm shorter than the other.
lazy mechanics way is to unwind the off drive side 1/2 turn at a time till the wheel is loose, save a representative spoke from each side then cut them out.
butcher was is just snip snip snip.
with the labor involved, but fresh.
and note the lengths, spokes should fill the nipple and not extend, drive side should be 1-2 mm shorter than the other.
lazy mechanics way is to unwind the off drive side 1/2 turn at a time till the wheel is loose, save a representative spoke from each side then cut them out.
butcher was is just snip snip snip.
Last edited by repechage; 12-17-21 at 08:47 AM.
Likes For repechage:
#3
Full Member
Thread Starter
Join Date: Dec 2020
Location: Minnesota
Posts: 305
Bikes: a few
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 92 Post(s)
Liked 379 Times
in
144 Posts
Replace- the plating is very thin. You Could clean them up and just set yourself up for future fast deterioration.
with the labor involved, but fresh.
and note the lengths, spokes should fill the nipple and not extend, drive side should be 1-2 mm shorter than the other.
lazy mechanics way is to unwind the off drive side 1/2 turn at a time till the wheel is loose, save a representative spoke from each side then cut them out.
butcher was is just snip snip snip.
with the labor involved, but fresh.
and note the lengths, spokes should fill the nipple and not extend, drive side should be 1-2 mm shorter than the other.
lazy mechanics way is to unwind the off drive side 1/2 turn at a time till the wheel is loose, save a representative spoke from each side then cut them out.
butcher was is just snip snip snip.
#4
working on my sandal tan
Join Date: Aug 2011
Location: CID
Posts: 22,629
Bikes: 1991 Bianchi Eros, 1964 Armstrong, 1988 Diamondback Ascent, 1988 Bianchi Premio, 1987 Bianchi Sport SX, 1980s Raleigh mixte (hers), All-City Space Horse (hers)
Mentioned: 98 Post(s)
Tagged: 0 Thread(s)
Quoted: 3871 Post(s)
Liked 2,568 Times
in
1,579 Posts
Likes For ThermionicScott:
#5
...
Join Date: Oct 2021
Location: Whitestone and Rensselaerville, New York
Posts: 1,510
Bikes: Bicycles? Yup.
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 481 Post(s)
Liked 1,585 Times
in
734 Posts
If you have a spare front fork to help with the wheel trueing, I vote replace.
The wheelbuilding-trueing process is very well documented, requiring little to get started besides patience and focus. I enjoy it, some do not.
The hubs and rims will clean up much faster/better with the old spokes removed.
The wheelbuilding-trueing process is very well documented, requiring little to get started besides patience and focus. I enjoy it, some do not.
The hubs and rims will clean up much faster/better with the old spokes removed.
Likes For BTinNYC:
#6
Senior Member
Join Date: Jun 2006
Posts: 20,305
Mentioned: 130 Post(s)
Tagged: 0 Thread(s)
Quoted: 3464 Post(s)
Liked 2,829 Times
in
1,995 Posts
Flag one spoke with tape, to the left of the valve hole. Do the front wheel first..
Photograph it. then get to work.
This is a four cross wheel, a bit more thinking than a 3X to keep everything in the correct orientation.
Photograph it. then get to work.
This is a four cross wheel, a bit more thinking than a 3X to keep everything in the correct orientation.
#7
Senior Member
Join Date: May 2012
Location: Point Reyes Station, California
Posts: 4,528
Bikes: Indeed!
Mentioned: 92 Post(s)
Tagged: 0 Thread(s)
Quoted: 1507 Post(s)
Liked 3,478 Times
in
1,132 Posts
If you decide to replace them one at a time, take the advise of repechage above and loosen them 1/2 turn at a time until they are slack before removing and replacing any. Then tighten and true up the wheel after all the spokes have been replaced. Given the corrosion on those spokes you may find that some nipples are seized to the spokes and will not turn without a good penetrating oil soak.
Brent
Brent
Likes For obrentharris:
#8
Senior Member
Join Date: Jan 2015
Location: Los Angeles
Posts: 4,704
Bikes: 82 Medici, 2011 Richard Sachs, 2011 Milwaukee Road
Mentioned: 55 Post(s)
Tagged: 0 Thread(s)
Quoted: 1949 Post(s)
Liked 2,010 Times
in
1,109 Posts
YEP. While you are planning, put a drop of Liquid Wrench or similar at both sides of the nipple spoke interface so it can start working. A good investment and Winter reading: https://www.wheelpro.co.uk/wheelbuilding/book.php
__________________
I don't do: disks, tubeless, e-shifting, or bead head nymphs.
I don't do: disks, tubeless, e-shifting, or bead head nymphs.
Likes For Classtime:
Likes For BTinNYC:
#10
feros ferio
Join Date: Jul 2000
Location: www.ci.encinitas.ca.us
Posts: 21,798
Bikes: 1959 Capo Modell Campagnolo; 1960 Capo Sieger (2); 1962 Carlton Franco Suisse; 1970 Peugeot UO-8; 1982 Bianchi Campione d'Italia; 1988 Schwinn Project KOM-10;
Mentioned: 44 Post(s)
Tagged: 0 Thread(s)
Quoted: 1393 Post(s)
Liked 1,325 Times
in
837 Posts
In this case, I concur. For a more experienced wheel builder, I suggest considering relacing with shorter spokes in a 3X pattern.
__________________
"Far and away the best prize that life offers is the chance to work hard at work worth doing." --Theodore Roosevelt
Capo: 1959 Modell Campagnolo, S/N 40324; 1960 Sieger (2), S/N 42624, 42597
Carlton: 1962 Franco Suisse, S/N K7911
Peugeot: 1970 UO-8, S/N 0010468
Bianchi: 1982 Campione d'Italia, S/N 1.M9914
Schwinn: 1988 Project KOM-10, S/N F804069
"Far and away the best prize that life offers is the chance to work hard at work worth doing." --Theodore Roosevelt
Capo: 1959 Modell Campagnolo, S/N 40324; 1960 Sieger (2), S/N 42624, 42597
Carlton: 1962 Franco Suisse, S/N K7911
Peugeot: 1970 UO-8, S/N 0010468
Bianchi: 1982 Campione d'Italia, S/N 1.M9914
Schwinn: 1988 Project KOM-10, S/N F804069
#11
Senior Member
Join Date: Jun 2010
Location: Medford MA
Posts: 2,089
Bikes: Ron Cooper touring, 1959 Jack Taylor 650b ladyback touring tandem, Vitus 979, Joe Bell painted Claud Butler Dalesman, Colin Laing curved tube tandem, heavily-Dilberted 1982 Trek 6xx, René Herse tandem
Mentioned: 80 Post(s)
Tagged: 0 Thread(s)
Quoted: 964 Post(s)
Liked 1,451 Times
in
723 Posts
I guess I don't agree. I wouldn't change the spokes.
I would ride this wheelset into the ground, abuse it and destroy it, meanwhile save your money for a set of nice touring wheels, 700c with a freehub in back and a dynamo hub in front. The old cantilever-braked Univegas are fine to put 700c wheels on, even if they came with 27" originally. You'll have to adjust the brakes somewhat, and you'll have to spread your frame to accept the wider rear wheel. Easy. After you change to 700c, you'll have more room for nice wide supple tires and many more tire options with 700c. You can have 8, 9, or even 10 gears in back. The whole setup will likely be lighter than what you have. Plus, no more breaking axles 'cause you will be using a cassette hub.
I would ride this wheelset into the ground, abuse it and destroy it, meanwhile save your money for a set of nice touring wheels, 700c with a freehub in back and a dynamo hub in front. The old cantilever-braked Univegas are fine to put 700c wheels on, even if they came with 27" originally. You'll have to adjust the brakes somewhat, and you'll have to spread your frame to accept the wider rear wheel. Easy. After you change to 700c, you'll have more room for nice wide supple tires and many more tire options with 700c. You can have 8, 9, or even 10 gears in back. The whole setup will likely be lighter than what you have. Plus, no more breaking axles 'cause you will be using a cassette hub.
__________________
Owner & co-founder, Cycles René Hubris. Unfortunately attaching questionable braze-ons to perfectly good frames since about 2015. With style.
Owner & co-founder, Cycles René Hubris. Unfortunately attaching questionable braze-ons to perfectly good frames since about 2015. With style.
Likes For scarlson:
#12
Senior Member
Join Date: Jun 2006
Posts: 20,305
Mentioned: 130 Post(s)
Tagged: 0 Thread(s)
Quoted: 3464 Post(s)
Liked 2,829 Times
in
1,995 Posts
I would hesitate to suggest moving from 27” to 700c with cantilevers will work- it can but what will happen is the radius the brake pad swings is 4 mm shorter- some cantilevers will allow that well enough, but not all.
test, don’t guess.
I have seen situations where the pad makes contact but after some wear- accelerated due to the shorter arc, the pad can dive inside the rim diameter and even lock, not retracting.
the other benefits of a freehub are sound, and greater tire selection.
my Paramount tandem is one of those bikes where, moving to 700c would be a no go.
pivots are too far apart left to right also.
test, don’t guess.
I have seen situations where the pad makes contact but after some wear- accelerated due to the shorter arc, the pad can dive inside the rim diameter and even lock, not retracting.
the other benefits of a freehub are sound, and greater tire selection.
my Paramount tandem is one of those bikes where, moving to 700c would be a no go.
pivots are too far apart left to right also.
#13
Full Member
Thread Starter
Join Date: Dec 2020
Location: Minnesota
Posts: 305
Bikes: a few
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 92 Post(s)
Liked 379 Times
in
144 Posts
Hey All - I appreciate all the comments on this question.
Just a few things: This is a 27" wheel with 36 spokes on a 3 cross pattern. The length of the spokes is 310 and right now availability (Yes Stainless Double Butted) is not so good like nothing out there. The '81 Univega Specialissima came with Dia-Compe Grand Compe Center Pull (not canitlever) - Beautiful looking gems if I might add. So I might take a trip to the bike shop to see what they have available. Should you have any suggestions for new spokes that would be available I would be all ears. I might need to move onto another area to work on while the search for spokes continues.
Just a few things: This is a 27" wheel with 36 spokes on a 3 cross pattern. The length of the spokes is 310 and right now availability (Yes Stainless Double Butted) is not so good like nothing out there. The '81 Univega Specialissima came with Dia-Compe Grand Compe Center Pull (not canitlever) - Beautiful looking gems if I might add. So I might take a trip to the bike shop to see what they have available. Should you have any suggestions for new spokes that would be available I would be all ears. I might need to move onto another area to work on while the search for spokes continues.
#14
working on my sandal tan
Join Date: Aug 2011
Location: CID
Posts: 22,629
Bikes: 1991 Bianchi Eros, 1964 Armstrong, 1988 Diamondback Ascent, 1988 Bianchi Premio, 1987 Bianchi Sport SX, 1980s Raleigh mixte (hers), All-City Space Horse (hers)
Mentioned: 98 Post(s)
Tagged: 0 Thread(s)
Quoted: 3871 Post(s)
Liked 2,568 Times
in
1,579 Posts
Hey All - I appreciate all the comments on this question.
Just a few things: This is a 27" wheel with 36 spokes on a 3 cross pattern. The length of the spokes is 310 and right now availability (Yes Stainless Double Butted) is not so good like nothing out there. The '81 Univega Specialissima came with Dia-Compe Grand Compe Center Pull (not canitlever) - Beautiful looking gems if I might add. So I might take a trip to the bike shop to see what they have available. Should you have any suggestions for new spokes that would be available I would be all ears. I might need to move onto another area to work on while the search for spokes continues.
Just a few things: This is a 27" wheel with 36 spokes on a 3 cross pattern. The length of the spokes is 310 and right now availability (Yes Stainless Double Butted) is not so good like nothing out there. The '81 Univega Specialissima came with Dia-Compe Grand Compe Center Pull (not canitlever) - Beautiful looking gems if I might add. So I might take a trip to the bike shop to see what they have available. Should you have any suggestions for new spokes that would be available I would be all ears. I might need to move onto another area to work on while the search for spokes continues.
#15
Full Member
Thread Starter
Join Date: Dec 2020
Location: Minnesota
Posts: 305
Bikes: a few
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 92 Post(s)
Liked 379 Times
in
144 Posts
In that case, I'd second @scarlson's suggestion to just clean up what you have and keep riding them for now. Q-Tips with solvent are good for cleaning out those little nooks around the spoke elbows. I'd oil and loosen each nipple slightly (to make sure they all break free and move without drama), then give the wheels a good true, trying to even out tensions wherever possible, then give them a really vigorous stress-relieving job. That is a good way to find out if any marginal spokes were about ready to break.
Merry Christmas and thanks for sharing your comments!
#16
...
Join Date: Oct 2021
Location: Whitestone and Rensselaerville, New York
Posts: 1,510
Bikes: Bicycles? Yup.
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 481 Post(s)
Liked 1,585 Times
in
734 Posts
A good cleanup & oil is always a good thing!
On the 3 vs 4 cross, when the spoke cross at the hub, even if the cross is hidden by the hub, it counts as 1 cross.
On the 3 vs 4 cross, when the spoke cross at the hub, even if the cross is hidden by the hub, it counts as 1 cross.
Likes For BTinNYC:
Likes For tjfastback66:
#18
Senior Member
Join Date: Apr 2007
Location: Thunder Bay, Ontario, Canada - burrrrr!
Posts: 11,674
Bikes: 1958 Rabeneick 120D, 1968 Legnano Gran Premio, 196? Torpado Professional, 2000 Marinoni Piuma
Mentioned: 210 Post(s)
Tagged: 0 Thread(s)
Quoted: 1372 Post(s)
Likes: 0
Liked 1,751 Times
in
938 Posts
When using plated spokes again, I clean them with aluminum foil first. This does a pretty good job of cleaning and smoothing. old spokes. I have used used stainless spokes many times and had very good results. I recommend stainless steel if one has access to them...
As found on late sixties Torpado plated spokes...
Cleaned up with foil and then waxed...
As found on late sixties Torpado plated spokes...
Cleaned up with foil and then waxed...
__________________
"98% of the bikes I buy are projects".
"98% of the bikes I buy are projects".
#19
Senior Member
Join Date: Apr 2005
Location: Ann Arbor, MI
Posts: 16,878
Bikes: 1980 Masi, 1984 Mondonico, 1984 Trek 610, 1980 Woodrup Giro, 2005 Mondonico Futura Leggera ELOS, 1967 PX10E, 1971 Peugeot UO-8
Mentioned: 49 Post(s)
Tagged: 0 Thread(s)
Quoted: 1857 Post(s)
Liked 664 Times
in
506 Posts
If you're gonna play the Butcher, be sure to unthread the freewheel before going happy with the diagonal cutters or nippers.
Likes For Road Fan:
#20
Strong Walker
Replace- the plating is very thin. You Could clean them up and just set yourself up for future fast deterioration.
with the labor involved, but fresh.
and note the lengths, spokes should fill the nipple and not extend, drive side should be 1-2 mm shorter than the other.
lazy mechanics way is to unwind the off drive side 1/2 turn at a time till the wheel is loose, save a representative spoke from each side then cut them out.
butcher was is just snip snip snip.
with the labor involved, but fresh.
and note the lengths, spokes should fill the nipple and not extend, drive side should be 1-2 mm shorter than the other.
lazy mechanics way is to unwind the off drive side 1/2 turn at a time till the wheel is loose, save a representative spoke from each side then cut them out.
butcher was is just snip snip snip.
#21
Senior Member
Join Date: Jun 2006
Posts: 20,305
Mentioned: 130 Post(s)
Tagged: 0 Thread(s)
Quoted: 3464 Post(s)
Liked 2,829 Times
in
1,995 Posts
that was not the question- it was stated;
…” spokes have some rust and are crusty. Looking for advice on replacing the spokes or cleaning them up?”
there was only one close up image of a rear hub and immediately adjacent spokes. Taking the wheel apart and cleaning the plated spokes is a lot of work. I cannot make an assumption about the original poster’s full assessment.
cleaning the rust and “crust” will most likely require abrasion, brass wool, Astonish, no matter, the chances of removing the plating is reasonably high. The question was not are they going to structurally fail, but how to clean them up. With your description of vast experience, be helpful and describe how to go about cleaning the wheel for avoiding accelerated oxidization going forward.
…” spokes have some rust and are crusty. Looking for advice on replacing the spokes or cleaning them up?”
there was only one close up image of a rear hub and immediately adjacent spokes. Taking the wheel apart and cleaning the plated spokes is a lot of work. I cannot make an assumption about the original poster’s full assessment.
cleaning the rust and “crust” will most likely require abrasion, brass wool, Astonish, no matter, the chances of removing the plating is reasonably high. The question was not are they going to structurally fail, but how to clean them up. With your description of vast experience, be helpful and describe how to go about cleaning the wheel for avoiding accelerated oxidization going forward.
#22
Senior Member
Join Date: Oct 2012
Location: Berkeley CA
Posts: 2,536
Bikes: 1981 Ron Cooper, 1974 Cinelli Speciale Corsa, 2000 Gary Fisher Sugar 1, 1986 Miyata 710, 1982 Raleigh "International"
Mentioned: 97 Post(s)
Tagged: 0 Thread(s)
Quoted: 930 Post(s)
Liked 1,292 Times
in
488 Posts
I have two thoughts:
1. They don't look that bad so my tendency would be to just clean them up, with evaporust, aluminum foil, a bit of metal polish, etc.
2. If you really want to replace them, I would suggest that you go with slightly smaller diameter spokes on the non-drive-side of the rear wheel. This results in less of a tension imbalance than using the same spokes on each side and therefore a stronger wheel. For example, I typically use Sapim Lasers on the non-drive-side and Sapim Race spokes on the drive-side. Bear in mind that both of these spoke types are very lightweight and therefore a little tricky to true, but they worked for me. Even if using heavier spokes, I would probably use asymmetrical spoke gauges on the rear.
1. They don't look that bad so my tendency would be to just clean them up, with evaporust, aluminum foil, a bit of metal polish, etc.
2. If you really want to replace them, I would suggest that you go with slightly smaller diameter spokes on the non-drive-side of the rear wheel. This results in less of a tension imbalance than using the same spokes on each side and therefore a stronger wheel. For example, I typically use Sapim Lasers on the non-drive-side and Sapim Race spokes on the drive-side. Bear in mind that both of these spoke types are very lightweight and therefore a little tricky to true, but they worked for me. Even if using heavier spokes, I would probably use asymmetrical spoke gauges on the rear.
#23
Senior Member
Join Date: Jan 2017
Posts: 659
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 195 Post(s)
Liked 207 Times
in
126 Posts
My two cents: New spokes look awfully nice, double butted or not and the confidence you'd gain in rebuilding a wheel is immeasurable.
For a easy fix, If they clean up with no rust then your done. Rust penetrats sometimes work or aluminum foil or steel wool. If you have to go further I'd seriously go with new spokes.
Beyond that is medium sandpaper and silver paint.
There's plenty of material on the "how to" but I'd advise starting fresh without the crutch of changing over one spoke at a time. It'll actually slow you down and you'll be surprised how easy it is. If you have to back up at any point that's a good thing because you will have learned something.
For a easy fix, If they clean up with no rust then your done. Rust penetrats sometimes work or aluminum foil or steel wool. If you have to go further I'd seriously go with new spokes.
Beyond that is medium sandpaper and silver paint.
There's plenty of material on the "how to" but I'd advise starting fresh without the crutch of changing over one spoke at a time. It'll actually slow you down and you'll be surprised how easy it is. If you have to back up at any point that's a good thing because you will have learned something.
#24
Strong Walker
that was not the question- it was stated;
…” spokes have some rust and are crusty. Looking for advice on replacing the spokes or cleaning them up?”
there was only one close up image of a rear hub and immediately adjacent spokes. Taking the wheel apart and cleaning the plated spokes is a lot of work. I cannot make an assumption about the original poster’s full assessment.
cleaning the rust and “crust” will most likely require abrasion, brass wool, Astonish, no matter, the chances of removing the plating is reasonably high. The question was not are they going to structurally fail, but how to clean them up. With your description of vast experience, be helpful and describe how to go about cleaning the wheel for avoiding accelerated oxidization going forward.
…” spokes have some rust and are crusty. Looking for advice on replacing the spokes or cleaning them up?”
there was only one close up image of a rear hub and immediately adjacent spokes. Taking the wheel apart and cleaning the plated spokes is a lot of work. I cannot make an assumption about the original poster’s full assessment.
cleaning the rust and “crust” will most likely require abrasion, brass wool, Astonish, no matter, the chances of removing the plating is reasonably high. The question was not are they going to structurally fail, but how to clean them up. With your description of vast experience, be helpful and describe how to go about cleaning the wheel for avoiding accelerated oxidization going forward.
spokes that are chrome plated, though, are of a low quality and while they sometimes can be buffed I would always replace them with stainless ones.
Likes For martl:
#25
Senior Member
Join Date: Apr 2005
Location: Ann Arbor, MI
Posts: 16,878
Bikes: 1980 Masi, 1984 Mondonico, 1984 Trek 610, 1980 Woodrup Giro, 2005 Mondonico Futura Leggera ELOS, 1967 PX10E, 1971 Peugeot UO-8
Mentioned: 49 Post(s)
Tagged: 0 Thread(s)
Quoted: 1857 Post(s)
Liked 664 Times
in
506 Posts
Ok, I’ve started working on the wheels of these ExcelToo/steel rim wheels on my friends’ Witcombs. I need to despoke to install the Araya rims and to clean the hubs. I’ve regreased the fronts, but they’re still not as I would like. If I can’t sort and smooth the hubs, it’s replacement wheel time. For the reassembly I’ll clean and reuse the spokes (largely because the nipples are all in great condition) with rim washers, the Araya rims, and wired tires. I’ll be able to at least clean and inspect the bearings and see if I can restore them or must replace them.
This thread is helping me assess the safety of the spokes, in this incremental approach to restoration.
This thread is helping me assess the safety of the spokes, in this incremental approach to restoration.
Last edited by Road Fan; 12-19-21 at 08:26 AM.