Which 10spd road shifter?
#1
Senior Member
Thread Starter
Join Date: Jul 2012
Posts: 80
Likes: 0
Liked 0 Times
in
0 Posts
Which 10spd road shifter?
I've read that I can use a 10spd Shimano road shifter to operate a 9spd rapid rise rear derailleur. Is the Tiagra flat-bar shifter the one I'm looking? Or if there are others, which would be best for a mountain bike?
#2
Senior Member
Join Date: Dec 2009
Location: Melbourne, Oz
Posts: 9,562
Bikes: https://weightweenies.starbike.com/forum/viewtopic.php?f=10&t=152015&p=1404231
Liked 732 Times
in
519 Posts
What's the point of this? Is it that you can't find new 9spd MTB shifters?
Perhaps a ShiftMate could solve that. Or you could buy second hand.
Perhaps a ShiftMate could solve that. Or you could buy second hand.
#3
Wookie Jesus inspires me.
OP, what do you mean by "road shifter"? Are you talking about STI shifters? Just get a 9 speed, it will work perfectly and there are plenty of second-hand, cheap pieces around.
#4
Senior Member
Join Date: Dec 2009
Location: Melbourne, Oz
Posts: 9,562
Bikes: https://weightweenies.starbike.com/forum/viewtopic.php?f=10&t=152015&p=1404231
Liked 732 Times
in
519 Posts
Also, if you do go the ShiftMate with a 10spd shifter, it might be better to fit it near the shifter rather than the derailleur, in order maximise signal-to-noise in the system; the cable pull per 10spd shift is pretty damn small.
Of course, you'd miss out on the removal of a bit of friction from the RD loop the ShiftMate provides, and it'd look a bit weird, so try it the normal way first.
Of course, you'd miss out on the removal of a bit of friction from the RD loop the ShiftMate provides, and it'd look a bit weird, so try it the normal way first.
#6
Senior Member
Join Date: Dec 2009
Location: Melbourne, Oz
Posts: 9,562
Bikes: https://weightweenies.starbike.com/forum/viewtopic.php?f=10&t=152015&p=1404231
Liked 732 Times
in
519 Posts
Then I'd say just get a 10spd MTB shifter and ditch the Rapid Rise RD.
I have a feeling the cable pull increments aren't exactly linear, so a backwards derailleur sounds like a headache.
I have a feeling the cable pull increments aren't exactly linear, so a backwards derailleur sounds like a headache.
#7
Senior Member
Thread Starter
Join Date: Jul 2012
Posts: 80
Likes: 0
Liked 0 Times
in
0 Posts
#9
Senior Member
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656
Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!
Likes: 0
Liked 1,102 Times
in
747 Posts
Shouldn't be necessary. I'm using a Shiftmate to allow Campy brifters to shift a 10-speed Shimano rd and cassette and it works perfectly mounted at the rear derailleur.
#10
Senior Member
Join Date: Dec 2009
Location: Melbourne, Oz
Posts: 9,562
Bikes: https://weightweenies.starbike.com/forum/viewtopic.php?f=10&t=152015&p=1404231
Liked 732 Times
in
519 Posts
But if it didn't hold its tune, that'd be something to try.
Anyway, I think the Campy brifters pull more cable per click than Shimano, no?
Anyway, I think the Campy brifters pull more cable per click than Shimano, no?
#11
Guest
Join Date: Jul 2008
Location: Grid Reference, SK
Posts: 3,768
Bikes: I never learned to ride a bike. It is my deepest shame.
Likes: 0
Liked 6 Times
in
6 Posts
Rapid rise derailleurs will work perfectly in any application where non rapid-rise will work, IME. Meaning, the rapidrise 9 speed should work with the 10 speed flat bar road shifters.
I don't know about the front derailleurs, though.
I don't know about the front derailleurs, though.