1974 Raleigh Grand Prix Rehab...Part 5...Frame Alignment
#1
Senior Member
Thread Starter
Join Date: Jun 2018
Location: The Urban Shores Of Michigami
Posts: 1,753
Bikes: ........................................ .....Holdsworth "Special"..... .......Falcon "Special".......... .........Miyata 912........... ........................................
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 703 Post(s)
Liked 678 Times
in
423 Posts
1974 Raleigh Grand Prix Rehab...Part 5...Frame Alignment
I started assembling the bike today and got the derailleurs working great. When I tried to install the rear brake pads, I could not get the wheel centered in the seat stays. Checking the frame with a Park Frame Alignment Tool, I could see that the stays were off-center by 1/4". So with some scrap lumber I built this fixture to hold the frame securely while I wrenched the stays over with a 8 foot long 2x4. The fixture being attached to the floor proved to be very effective.
Last edited by branko_76; 05-16-20 at 03:33 PM.
#2
Senior Member
Thread Starter
Join Date: Jun 2018
Location: The Urban Shores Of Michigami
Posts: 1,753
Bikes: ........................................ .....Holdsworth "Special"..... .......Falcon "Special".......... .........Miyata 912........... ........................................
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 703 Post(s)
Liked 678 Times
in
423 Posts
#3
Senior Member
Join Date: Dec 2005
Posts: 17,195
Mentioned: 482 Post(s)
Tagged: 0 Thread(s)
Quoted: 3824 Post(s)
Liked 6,783 Times
in
2,637 Posts
Nice setup! When I've done that job, I install a couple of bottom bracket cups that I'm not terribly fond of and then place the frame in my vise, holding it by the cups.
#4
Senior Member
Thread Starter
Join Date: Jun 2018
Location: The Urban Shores Of Michigami
Posts: 1,753
Bikes: ........................................ .....Holdsworth "Special"..... .......Falcon "Special".......... .........Miyata 912........... ........................................
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 703 Post(s)
Liked 678 Times
in
423 Posts
I thought of doing that but my work bench is so cluttered that it was faster (and more fun) to just build this thing.
#5
Senior Member
Join Date: Aug 2007
Location: Evanston, IL
Posts: 5,133
Bikes: many
Mentioned: 63 Post(s)
Tagged: 0 Thread(s)
Quoted: 1457 Post(s)
Liked 1,408 Times
in
771 Posts
Interesting. I see conduit clips securing the dummy front axle. How is the bottom bracket shell secured, just the bottom bracket spindle riding in the two holes?
#6
Senior Member
Thread Starter
Join Date: Jun 2018
Location: The Urban Shores Of Michigami
Posts: 1,753
Bikes: ........................................ .....Holdsworth "Special"..... .......Falcon "Special".......... .........Miyata 912........... ........................................
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 703 Post(s)
Liked 678 Times
in
423 Posts
#7
Senior Member
Thread Starter
Join Date: Jun 2018
Location: The Urban Shores Of Michigami
Posts: 1,753
Bikes: ........................................ .....Holdsworth "Special"..... .......Falcon "Special".......... .........Miyata 912........... ........................................
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 703 Post(s)
Liked 678 Times
in
423 Posts
Aligning the seat and chain stays did not help. The wheel was still offset to the non-drive side by 3/8". Although not evident in the photo, I could see that the wheel was not parallel to the seat tube.
#8
Senior Member
Thread Starter
Join Date: Jun 2018
Location: The Urban Shores Of Michigami
Posts: 1,753
Bikes: ........................................ .....Holdsworth "Special"..... .......Falcon "Special".......... .........Miyata 912........... ........................................
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 703 Post(s)
Liked 678 Times
in
423 Posts
I almost gave up but after giving it a day to sink in, I took some measurements and found that the non-drive side seat and chain stays were slightly longer than the other side. With the help of AutoCAD, I input the wheel radius, the axle length between the dropouts and the amount of offset. Using the "alignment" command, I was able to get the exact measurement that the axle needed to drop on the drive-side to center the wheel.
Using a fresh "flat bastard" file, I took off about 1.5mm from the inner bottom of the drive-side dropout.
*remember kiddies, files only cut on the push stroke, dragging a file across the work surface on the return stroke will only shorten the life of the file...
Using a fresh "flat bastard" file, I took off about 1.5mm from the inner bottom of the drive-side dropout.
*remember kiddies, files only cut on the push stroke, dragging a file across the work surface on the return stroke will only shorten the life of the file...
Last edited by branko_76; 05-18-20 at 10:44 PM.
Likes For branko_76:
#9
Senior Member
Thread Starter
Join Date: Jun 2018
Location: The Urban Shores Of Michigami
Posts: 1,753
Bikes: ........................................ .....Holdsworth "Special"..... .......Falcon "Special".......... .........Miyata 912........... ........................................
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 703 Post(s)
Liked 678 Times
in
423 Posts
Since the d.o. has no integral derailleur hanger, the hanger attached to the simplex derailleur will position the axle...
#10
Senior Member
Thread Starter
Join Date: Jun 2018
Location: The Urban Shores Of Michigami
Posts: 1,753
Bikes: ........................................ .....Holdsworth "Special"..... .......Falcon "Special".......... .........Miyata 912........... ........................................
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 703 Post(s)
Liked 678 Times
in
423 Posts
The wheel is now centered and is also parallel to the seat-tube...
Likes For branko_76:
#11
Senior Member
Well done! I have had many bikes with odd misalignments. You do what you gotta do you make them "right".
Likes For big chainring:
#12
Newbie
Join Date: Nov 2021
Posts: 15
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 13 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
I started assembling the bike today and got the derailleurs working great. When I tried to install the rear brake pads, I could not get the wheel centered in the seat stays. Checking the frame with a Park Frame Alignment Tool, I could see that the stays were off-center by 1/4". So with some scrap lumber I built this fixture to hold the frame securely while I wrenched the stays over with a 8 foot long 2x4. The fixture being attached to the floor proved to be very effective.
Likes For mauin1x:
#13
feros ferio
Join Date: Jul 2000
Location: www.ci.encinitas.ca.us
Posts: 21,821
Bikes: 1959 Capo Modell Campagnolo; 1960 Capo Sieger (2); 1962 Carlton Franco Suisse; 1970 Peugeot UO-8; 1982 Bianchi Campione d'Italia; 1988 Schwinn Project KOM-10;
Mentioned: 44 Post(s)
Tagged: 0 Thread(s)
Quoted: 1398 Post(s)
Liked 1,343 Times
in
848 Posts
I envy your amount of workshop space.
__________________
"Far and away the best prize that life offers is the chance to work hard at work worth doing." --Theodore Roosevelt
Capo: 1959 Modell Campagnolo, S/N 40324; 1960 Sieger (2), S/N 42624, 42597
Carlton: 1962 Franco Suisse, S/N K7911
Peugeot: 1970 UO-8, S/N 0010468
Bianchi: 1982 Campione d'Italia, S/N 1.M9914
Schwinn: 1988 Project KOM-10, S/N F804069
"Far and away the best prize that life offers is the chance to work hard at work worth doing." --Theodore Roosevelt
Capo: 1959 Modell Campagnolo, S/N 40324; 1960 Sieger (2), S/N 42624, 42597
Carlton: 1962 Franco Suisse, S/N K7911
Peugeot: 1970 UO-8, S/N 0010468
Bianchi: 1982 Campione d'Italia, S/N 1.M9914
Schwinn: 1988 Project KOM-10, S/N F804069
Likes For John E:
#14
Senior Member
Join Date: Feb 2013
Location: Alta California
Posts: 14,346
Mentioned: 417 Post(s)
Tagged: 1 Thread(s)
Quoted: 3842 Post(s)
Liked 3,398 Times
in
2,216 Posts
-----
differing effective seat stay lengths is one of the nastier frame alignment problems to solve...
have had a couple frames come through where the unequalness could not be solved by the method you employed
---
on a visit to Bob Freeman on Bainbridge Island (Seattle) to receive a giro of his collezione in September 2001 he showed me his Baines/TJ Cycles Flying Gate
all of that thought/care/planning and use of the very best materials on a bespoke frameset and Trev had constructed it with dissimilar effective seat stay lengths so that the machine's stern round thing sat in there gollywompus
-----
differing effective seat stay lengths is one of the nastier frame alignment problems to solve...
have had a couple frames come through where the unequalness could not be solved by the method you employed
---
on a visit to Bob Freeman on Bainbridge Island (Seattle) to receive a giro of his collezione in September 2001 he showed me his Baines/TJ Cycles Flying Gate
all of that thought/care/planning and use of the very best materials on a bespoke frameset and Trev had constructed it with dissimilar effective seat stay lengths so that the machine's stern round thing sat in there gollywompus
-----
Last edited by juvela; 04-12-24 at 09:50 AM. Reason: addition
Likes For juvela:
#15
Senior Member
Join Date: Jan 2019
Location: Toledo Ohio
Posts: 1,508
Bikes: 1964 Huffy Sportsman, 1972 Fuji Newest, 1973 Schwinn Super Sport (3), 1982 Trek 412, 1983 Trek 700, 1989 Miyata 1000LT, 1991 Bianchi Boardwalk, plus others
Mentioned: 21 Post(s)
Tagged: 0 Thread(s)
Quoted: 585 Post(s)
Liked 704 Times
in
397 Posts
Isn’t this about the time someone comments on British manufacturing quality?
Likes For sd5782:
#16
Full Member
Join Date: Sep 2020
Location: Sacramento, CA
Posts: 418
Bikes: 2017 Sage Skyline, 2015 Co-Motion Periscope Tandem, 2012 Soma Smoothie, 2006 Kona Jake, 1978 Richard Sachs, 1977 Peugeot UO18c, 1977 Peugeot PRN10, 1974 Allegro Schweitzermeister Model 76, 1972 Hugo Rickert Spezial, 1971 Fuji Finest
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 119 Post(s)
Liked 630 Times
in
198 Posts
The brake bridge brazed on a slant sure caught my eye
I’ve always pictured Bike Boom manufacturing to be like that movie scene in “The Court Jester” with Danny Kaye where they compress his knighthood training into one day using a process that normally takes a few months.
Likes For Sactown_Albert:
#17
Senior Member
Join Date: Nov 2019
Location: SF Bay Area
Posts: 506
Bikes: Raleigh Super Course, Raleigh International, Raleigh Gran Sport
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 252 Post(s)
Liked 319 Times
in
198 Posts
You know, I've taken as many pokes at Bike Boom British quality as most of us. But, at the same time, I am also impressed by my three early '70s Raleighs that are in near daily use that all still look good and ride great, despite being 50 years old. I have few other material possessions that have held up so well for so long.
Likes For daka:
#18
Senior Member
Join Date: Jan 2019
Location: Toledo Ohio
Posts: 1,508
Bikes: 1964 Huffy Sportsman, 1972 Fuji Newest, 1973 Schwinn Super Sport (3), 1982 Trek 412, 1983 Trek 700, 1989 Miyata 1000LT, 1991 Bianchi Boardwalk, plus others
Mentioned: 21 Post(s)
Tagged: 0 Thread(s)
Quoted: 585 Post(s)
Liked 704 Times
in
397 Posts
And I will admit that I kinda have a hankering for an early International.
#19
Senior Member
Thread Starter
Join Date: Jun 2018
Location: The Urban Shores Of Michigami
Posts: 1,753
Bikes: ........................................ .....Holdsworth "Special"..... .......Falcon "Special".......... .........Miyata 912........... ........................................
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 703 Post(s)
Liked 678 Times
in
423 Posts