Crank Arm Bolt Torque Setting
#1
Urban Cyclist
Thread Starter
Join Date: Jan 2007
Location: USA
Posts: 18
Bikes: Guerciotti SLX - 84', Tide-Ace 11sp carbon frame & misc. Shimano parts
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 8 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Crank Arm Bolt Torque Setting
I couldn't find any documentation on torque specs for vintage Shimano from the 80's. Do you tighten the crank arm bolt by feel or a specific value?
#2
Forum Moderator
Join Date: Jul 2007
Location: Kalamazoo MI
Posts: 20,650
Bikes: Fuji SL2.1 Carbon Di2 Cannondale Synapse Alloy 4 Trek Checkpoint ALR-5 Viscount Aerospace Pro Colnago Classic Rabobank Schwinn Waterford PMount Raleigh C50 Cromoly Hybrid Legnano Tipo Roma Pista
Mentioned: 59 Post(s)
Tagged: 0 Thread(s)
Quoted: 3091 Post(s)
Liked 6,601 Times
in
3,785 Posts
Post moved from Sales thread to its own thread in Mechanics.
__________________
#3
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,096
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4210 Post(s)
Liked 3,878 Times
in
2,315 Posts
That era usually had crank arm retaining bolts torqued to around 30ft/lb. Did you check out the Park torque spec chart? Andy
__________________
AndrewRStewart
AndrewRStewart
#4
Senior Member
Join Date: Apr 2009
Location: New Rochelle, NY
Posts: 38,725
Bikes: too many bikes from 1967 10s (5x2)Frejus to a Sumitomo Ti/Chorus aluminum 10s (10x2), plus one non-susp mtn bike I use as my commuter
Mentioned: 140 Post(s)
Tagged: 1 Thread(s)
Quoted: 5793 Post(s)
Liked 2,585 Times
in
1,433 Posts
Back when those cranks were made, nobody spoke torque spec.
Do it the old fashioned way, tightening until the torque ramps up toward the wall.
Do it the old fashioned way, tightening until the torque ramps up toward the wall.
__________________
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
Likes For FBinNY:
#5
Really Old Senior Member
IF you have a torque wrench, 30-35 Ft-Lb.
Else, good & tight.
BTW, the first time I torqued one, it was more force than I expected. Possibly from a more awkward position?
Else, good & tight.
BTW, the first time I torqued one, it was more force than I expected. Possibly from a more awkward position?
#6
SE Wis
Join Date: Apr 2005
Location: Milwaukee, WI
Posts: 10,517
Bikes: '68 Raleigh Sprite, '02 Raleigh C500, '84 Raleigh Gran Prix, '91 Trek 400, 2013 Novara Randonee, 1990 Trek 970
Mentioned: 40 Post(s)
Tagged: 0 Thread(s)
Quoted: 2747 Post(s)
Liked 3,401 Times
in
2,058 Posts
By feel. Check tightness again after first ride
#7
Senior Member
Join Date: Apr 2009
Location: New Rochelle, NY
Posts: 38,725
Bikes: too many bikes from 1967 10s (5x2)Frejus to a Sumitomo Ti/Chorus aluminum 10s (10x2), plus one non-susp mtn bike I use as my commuter
Mentioned: 140 Post(s)
Tagged: 1 Thread(s)
Quoted: 5793 Post(s)
Liked 2,585 Times
in
1,433 Posts
One guide to proper torque is the length of the tool used.
BITD cranks were tightened with the "peanut butter" wrench. This was about 7" long, just clearing the pedal. Tighten with something shy of the max force you can muster.
BITD cranks were tightened with the "peanut butter" wrench. This was about 7" long, just clearing the pedal. Tighten with something shy of the max force you can muster.
Last edited by FBinNY; 03-26-24 at 08:22 PM.
#8
I'm good to go!
Join Date: Jul 2017
Location: Mississippi
Posts: 14,992
Bikes: Tarmac Disc Comp Di2 - 2020
Mentioned: 51 Post(s)
Tagged: 0 Thread(s)
Quoted: 6196 Post(s)
Liked 4,811 Times
in
3,319 Posts
You couldn't find any documentation? You must not have gone to Shimano's Technical Document Site.
They still have the old SI's that were used back then. All you need to know is the part number. Which you can use the cranks PN which is around the hole for the pedal on the inboard side.
Here is the SI for a early 80's Deore crank FC-M730... https://si.shimano.com/en/pdfs/si/T-...000-00-ENG.pdf
I usually go by feel for all the bolts and nuts on my bike. Very occasionally, I'll double check myself with a torque wrench to see if I'm in the ball park.
They still have the old SI's that were used back then. All you need to know is the part number. Which you can use the cranks PN which is around the hole for the pedal on the inboard side.
Here is the SI for a early 80's Deore crank FC-M730... https://si.shimano.com/en/pdfs/si/T-...000-00-ENG.pdf
I usually go by feel for all the bolts and nuts on my bike. Very occasionally, I'll double check myself with a torque wrench to see if I'm in the ball park.
Last edited by Iride01; 03-27-24 at 08:01 AM.
#9
aged to perfection
Join Date: Jun 2009
Location: PacNW
Posts: 1,817
Bikes: Dinucci Allez 2.0, Richard Sachs, Alex Singer, Serotta, Masi GC, Raleigh Pro Mk.1, Hetchins, etc
Mentioned: 24 Post(s)
Tagged: 0 Thread(s)
Quoted: 839 Post(s)
Liked 1,258 Times
in
663 Posts
I recommend 260 - 300 in lb.
Less for classic campagnolo. Even less for Stronglight.
/markp
Less for classic campagnolo. Even less for Stronglight.
/markp
#10
Senior Member
Join Date: Jan 2019
Location: Toledo Ohio
Posts: 1,496
Bikes: 1964 Huffy Sportsman, 1972 Fuji Newest, 1973 Schwinn Super Sport (3), 1982 Trek 412, 1983 Trek 700, 1989 Miyata 1000LT, 1991 Bianchi Boardwalk, plus others
Mentioned: 21 Post(s)
Tagged: 0 Thread(s)
Quoted: 583 Post(s)
Liked 699 Times
in
394 Posts
I’m with Mark here or even slightly less. I’ve not done loads, but when my beam type torque wrench starts getting to 250 inch/lbs it just seems tight. Things almost feel like the aluminum is going to split going more. I used to just torque pretty darn tight with a 1/2” socket wrench. Putting on the torque wrench was a surprise as I needed a lot more to even get to 250. It scares me going higher, but I am not a strong rider. I do recheck just once with the ratchet after a couple rides.
Likes For sd5782: