Garmin Cadence Sensor Rubber Rubbing Bootie
#1
Grupetto Bob
Thread Starter
Join Date: Sep 2020
Location: Seattle-ish
Posts: 6,215
Bikes: Bikey McBike Face
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 2581 Post(s)
Liked 5,638 Times
in
2,921 Posts
Garmin Cadence Sensor Rubber Rubbing Bootie
There is just no way to write the title without it sounding a bit off.
Since the weather in the Seattle hinterlands is getting cool - 40s and raining, it was time to don the neoprene booties. The rubber retaining strap, no matter where I move it on the crank rubs against the bootie (keep it clean) creating a wear spot. Was thinking instead of using the rubber strap, perhaps use something lower profile like the black twist-ties which come with electronic accessories. Not an elegant solution so am putting out to the brain trust on suggestions. Gracias
Since the weather in the Seattle hinterlands is getting cool - 40s and raining, it was time to don the neoprene booties. The rubber retaining strap, no matter where I move it on the crank rubs against the bootie (keep it clean) creating a wear spot. Was thinking instead of using the rubber strap, perhaps use something lower profile like the black twist-ties which come with electronic accessories. Not an elegant solution so am putting out to the brain trust on suggestions. Gracias
__________________
Road 🚴🏾♂️ & Mountain 🚵🏾♂️
Road 🚴🏾♂️ & Mountain 🚵🏾♂️
#2
Expired Member
Join Date: Jun 2007
Location: TN
Posts: 11,543
Mentioned: 37 Post(s)
Tagged: 0 Thread(s)
Quoted: 3672 Post(s)
Liked 5,430 Times
in
2,759 Posts
The Wahoo can be mounted directly to the crank arm with double sided tape. Maybe that would work for the Garmin? Tape comes in a range of hold strengths.
Likes For shelbyfv:
#3
Super Modest
Join Date: Jun 2002
Location: Central Illinois
Posts: 23,466
Bikes: Trek Emonda, Giant Propel, Colnago V3, Co-Motion Supremo, ICE VTX WC
Mentioned: 107 Post(s)
Tagged: 1 Thread(s)
Quoted: 10963 Post(s)
Liked 4,620 Times
in
2,123 Posts
I've used Gorilla double-sided tape before and it held well.
__________________
Keep the chain tight!
Likes For Trsnrtr:
#4
Full Member
I use a bit of the 3m tape. I didn't trust it to stay and based off a video I saw I put about an inch of mountain bike tube over the top. Holds it securely.
Likes For ratell:
#5
Thread Killer
Join Date: Aug 2008
Location: Ann Arbor, MI
Posts: 12,440
Bikes: 15 Kinesis Racelight 4S, 76 Motebecane Gran Jubilée, 17 Dedacciai Gladiatore2, 12 Breezer Venturi, 09 Dahon Mariner, 12 Mercier Nano, 95 DeKerf Team SL, 19 Tern Rally, 21 Breezer Doppler Cafe+, 19 T-Lab X3, 91 Serotta CII, 23 3T Strada
Mentioned: 30 Post(s)
Tagged: 0 Thread(s)
Quoted: 3143 Post(s)
Liked 1,707 Times
in
1,031 Posts
You might try some 3M Dual Lock for the ease of removal and re-installation. Probably the low-pro SJ4580 is the way to go for maximum chainstay clearance.
Likes For chaadster:
#6
Grupetto Bob
Thread Starter
Join Date: Sep 2020
Location: Seattle-ish
Posts: 6,215
Bikes: Bikey McBike Face
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 2581 Post(s)
Liked 5,638 Times
in
2,921 Posts
My only concern about double sided tape is when it comes time to replace the battery which means scraping the tape off the door. Not a problem?
__________________
Road 🚴🏾♂️ & Mountain 🚵🏾♂️
Road 🚴🏾♂️ & Mountain 🚵🏾♂️
#7
Super Modest
Join Date: Jun 2002
Location: Central Illinois
Posts: 23,466
Bikes: Trek Emonda, Giant Propel, Colnago V3, Co-Motion Supremo, ICE VTX WC
Mentioned: 107 Post(s)
Tagged: 1 Thread(s)
Quoted: 10963 Post(s)
Liked 4,620 Times
in
2,123 Posts
I have just used electrical tape. The tape doesn't look any worse than the rubber strap.
__________________
Keep the chain tight!
#8
Advocatus Diaboli
Join Date: Feb 2015
Location: Wherever I am
Posts: 8,635
Bikes: Merlin Cyrene, Nashbar steel CX
Mentioned: 14 Post(s)
Tagged: 1 Thread(s)
Quoted: 4733 Post(s)
Liked 1,532 Times
in
1,003 Posts
Sounds like a good excuse to get a Stages or some other type of power meter with built-in cadence.