Plus or minus suggested size
#1
Banned.
Thread Starter
Plus or minus suggested size
Hello I've been building bikes for kin and myself for years. just recently I've got into knowing about sizes of bikes. Before I used to set up the handle bars seat height and angle to positions that I thought just looked cool but not anymore.
I believe I'm putting this in the correct section because I'm not asking about components or techniques. I've measured my inseam length to be just under 33" so about 83cm
Some road bike size calculators suggest me a frame size of 55 to 55.5cm
As I am still building and shopping for bikes or frames to build. My question is how far higher or lower can I go from my suggested size. Considering I am 6ft tall and probably won't grow anymore at my 35 years of age.
my theory is that I can go a bit lower and find the sweet spot by raising the seat post incrementally but I shouldn't go higher bc I can't do the opposite if it's too high.
I believe I'm putting this in the correct section because I'm not asking about components or techniques. I've measured my inseam length to be just under 33" so about 83cm
Some road bike size calculators suggest me a frame size of 55 to 55.5cm
As I am still building and shopping for bikes or frames to build. My question is how far higher or lower can I go from my suggested size. Considering I am 6ft tall and probably won't grow anymore at my 35 years of age.
my theory is that I can go a bit lower and find the sweet spot by raising the seat post incrementally but I shouldn't go higher bc I can't do the opposite if it's too high.
#2
blahblahblah chrome moly
Join Date: Apr 2009
Location: Seattle
Posts: 1,994
Mentioned: 92 Post(s)
Tagged: 0 Thread(s)
Quoted: 1181 Post(s)
Liked 2,576 Times
in
1,076 Posts
How important is standover height to you? It's more important to some people, but I say don't build a bike for standing over, build it for riding. Not to the extreme where you actually can't stand over it without injuring yourself, but I bet you can lift your current bike while straddling it, right? Lift both wheels off the ground and see how high it goes before getting uncomfortable. That's how much larger you can go.
Handlebar height is the main reason for "frame size" (seat tube length) anyway, for traditional level-toptube frames. If you like the bars higher than a racer, you can get it on a small frame with a long up-jutting stem, but those are structurally inefficient and look ugly. Designing the top of the head tube based on desired handlebar height, and the top of the seat tube by standover, you might end up with a sloping toptube. That used to be something bikies shunned because their favorite racer had a level TT, but nowadays practically all the pros have a sloping TT.
So design the frame around the contact points with your body: hbars, saddle and pedals, maybe middle of the TT if standover clearance is a must. I recommend drawing a frame full-size on paper, at least until you get a handle on the process. Or do it on the computer if you're an expert CAD-jockey. I haven't drawn a frame on paper since the '70s but I'm glad I did, it taught me stuff.
Framebuilders shouldn't be paying any attention to what someone else "recommends" as your frame size. Try different things until you know what works for you. Generalizing that to other people is tricky and can take years or decades to get good at even for a full-timer, so getting ideas from other brands is acceptable, but don't be afraid to diverge from the designs others are using. Definitely don't slavishly follow what racers are doing. Unless you're actually pinning a number on your jersey, you probably shouldn't be riding in that position.
Handlebar height is the main reason for "frame size" (seat tube length) anyway, for traditional level-toptube frames. If you like the bars higher than a racer, you can get it on a small frame with a long up-jutting stem, but those are structurally inefficient and look ugly. Designing the top of the head tube based on desired handlebar height, and the top of the seat tube by standover, you might end up with a sloping toptube. That used to be something bikies shunned because their favorite racer had a level TT, but nowadays practically all the pros have a sloping TT.
So design the frame around the contact points with your body: hbars, saddle and pedals, maybe middle of the TT if standover clearance is a must. I recommend drawing a frame full-size on paper, at least until you get a handle on the process. Or do it on the computer if you're an expert CAD-jockey. I haven't drawn a frame on paper since the '70s but I'm glad I did, it taught me stuff.
Framebuilders shouldn't be paying any attention to what someone else "recommends" as your frame size. Try different things until you know what works for you. Generalizing that to other people is tricky and can take years or decades to get good at even for a full-timer, so getting ideas from other brands is acceptable, but don't be afraid to diverge from the designs others are using. Definitely don't slavishly follow what racers are doing. Unless you're actually pinning a number on your jersey, you probably shouldn't be riding in that position.
Last edited by bulgie; 02-11-24 at 01:43 PM.
Likes For bulgie:
#4
Senior Member
Join Date: May 2010
Location: Bastrop Texas
Posts: 4,490
Bikes: Univega, Peu P6, Peu PR-10, Ted Williams, Peu UO-8, Peu UO-18 Mixte, Peu Dolomites
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 970 Post(s)
Liked 1,635 Times
in
1,049 Posts
I found my sweet spot for bicycle size by trail and error. Over the years it has slowly changed so I now keep detailed specs on what feels comfortable for me. If you have been riding regularly you should be able to find your sweet spot pretty easy. Once found take those measurements and keep them close.
Note that at 70 years my bikes are not set up anything like they were 50 years ago... Ha
Note that at 70 years my bikes are not set up anything like they were 50 years ago... Ha
__________________
No matter where you're at... There you are... Δf:=f(1/2)-f(-1/2)
No matter where you're at... There you are... Δf:=f(1/2)-f(-1/2)
Likes For zandoval:
#5
blahblahblah chrome moly
Join Date: Apr 2009
Location: Seattle
Posts: 1,994
Mentioned: 92 Post(s)
Tagged: 0 Thread(s)
Quoted: 1181 Post(s)
Liked 2,576 Times
in
1,076 Posts
Likes For bulgie:
#6
Randomhead
Join Date: Aug 2008
Location: Happy Valley, Pennsylvania
Posts: 24,402
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
Liked 3,702 Times
in
2,522 Posts
There is a forum about fitting.
Likes For unterhausen:
#7
Senior Member
Join Date: May 2010
Location: Bastrop Texas
Posts: 4,490
Bikes: Univega, Peu P6, Peu PR-10, Ted Williams, Peu UO-8, Peu UO-18 Mixte, Peu Dolomites
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 970 Post(s)
Liked 1,635 Times
in
1,049 Posts