Shift cable splitters without cable stops
#1
Full Member
Thread Starter
Shift cable splitters without cable stops
CLOSED
Cable splitter between cable stops. This is not my bike.
Must a cable splitter be used between cable stops brazed/attached to the frame?
Are there any models of cable splitters that can be used without cable stops? The cable housing will butt against the cable splitter, if used without cable stops.
Cable splitter between cable stops. This is not my bike.
Must a cable splitter be used between cable stops brazed/attached to the frame?
Are there any models of cable splitters that can be used without cable stops? The cable housing will butt against the cable splitter, if used without cable stops.
Last edited by anga; 12-03-22 at 09:39 AM.
#2
Senior Member
Join Date: Jan 2013
Posts: 2,679
Bikes: too many sparkly Italians, some sweet Americans and a couple interesting Japanese
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 569 Post(s)
Liked 581 Times
in
409 Posts
Can't understand what you are asking, "cable housing will butt against the cable splitter" on your bike which is not shown above?
#3
SE Wis
Join Date: Apr 2005
Location: Milwaukee, WI
Posts: 10,515
Bikes: '68 Raleigh Sprite, '02 Raleigh C500, '84 Raleigh Gran Prix, '91 Trek 400, 2013 Novara Randonee, 1990 Trek 970
Mentioned: 40 Post(s)
Tagged: 0 Thread(s)
Quoted: 2747 Post(s)
Liked 3,394 Times
in
2,056 Posts
#4
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,082
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4204 Post(s)
Liked 3,862 Times
in
2,310 Posts
Well, for the splitters shown the inner cables must be exposed. I know of no splitter that can work with an inner cable still inside housing. If the frame has round tubes it's not hard to make (or buy) clamp around housing stops. Andy
__________________
AndrewRStewart
AndrewRStewart
Likes For Andrew R Stewart:
#5
Senior Member
Join Date: Apr 2009
Location: New Rochelle, NY
Posts: 38,713
Bikes: too many bikes from 1967 10s (5x2)Frejus to a Sumitomo Ti/Chorus aluminum 10s (10x2), plus one non-susp mtn bike I use as my commuter
Mentioned: 140 Post(s)
Tagged: 1 Thread(s)
Quoted: 5782 Post(s)
Liked 2,578 Times
in
1,429 Posts
If I read your intent correctly, the answer is a clear NO.
For cables to work there has to be relative movement between the inner wire and the housing. Butting housing up against the splitter would preclude that, thereby disabling the cable.
BTW "cable splitter"can also refer to devices that allow a single lever to control 2 brakes. If you're referring to those, then I believe that there some that will serve your purpose
For cables to work there has to be relative movement between the inner wire and the housing. Butting housing up against the splitter would preclude that, thereby disabling the cable.
BTW "cable splitter"can also refer to devices that allow a single lever to control 2 brakes. If you're referring to those, then I believe that there some that will serve your purpose
Last edited by FBinNY; 12-03-22 at 02:48 PM.
Likes For FBinNY:
#6
Full Member
Thread Starter
Spent some enjoyable time figuring this out.