Sandy silt a problem?
#1
old newbie
Thread Starter
Join Date: Nov 2009
Location: Fort Worth, Texas
Posts: 866
Bikes: Specialized Roubaix
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 541 Post(s)
Liked 359 Times
in
182 Posts
Sandy silt a problem?
I was riding a local paved trail at a small lake. There is construction around part of it. Besides some water seeping across the path there was a stretch about 40-50 feet along the path with a wet fine silt. It splashed all over the bike. I figure some must have got in the chain.
I hosed it off when I got home. Is that good enough? When it dries I will re-lube it.
I really don’t know all of the places it could get that can cause problems, if it is a problem.
I hosed it off when I got home. Is that good enough? When it dries I will re-lube it.
I really don’t know all of the places it could get that can cause problems, if it is a problem.
#2
Habitual User
Join Date: Jan 2020
Location: Altadena, CA
Posts: 7,997
Bikes: 2023 Niner RLT 9 RDO, 2018 Trek Procaliber 9.9 RSL, 2018 Storck Fascenario.3 Platinum, 2003 Time VX Special Pro, 2001 Colnago VIP, 1999 Trek 9900 singlespeed, 1977 Nishiki ONP
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 4957 Post(s)
Liked 8,099 Times
in
3,833 Posts
Time for a new bike, obviously.
Or, you're probably fine. I ride my gravel bike and MTB through some pretty dirty/mucky conditions on a regular basis. After I ride, I hose it off, wipe it down, and re-lube the chain. All good. My road bike gets the same treatment when it needs it. The components of a road bike aren't significantly more delicate than those of a gravel bike or MTB. Actually, my first gravel bike was all road components (Ultegra).
Or, you're probably fine. I ride my gravel bike and MTB through some pretty dirty/mucky conditions on a regular basis. After I ride, I hose it off, wipe it down, and re-lube the chain. All good. My road bike gets the same treatment when it needs it. The components of a road bike aren't significantly more delicate than those of a gravel bike or MTB. Actually, my first gravel bike was all road components (Ultegra).
__________________
"Swedish fish. They're protein shaped." - livedarklions
"Swedish fish. They're protein shaped." - livedarklions
Likes For Eric F:
#3
old newbie
Thread Starter
Join Date: Nov 2009
Location: Fort Worth, Texas
Posts: 866
Bikes: Specialized Roubaix
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 541 Post(s)
Liked 359 Times
in
182 Posts
Time for a new bike, obviously.
Or, you're probably fine. I ride my gravel bike and MTB through some pretty dirty/mucky conditions on a regular basis. After I ride, I hose it off, wipe it down, and re-lube the chain. All good. My road bike gets the same treatment when it needs it. The components of a road bike aren't significantly more delicate than those of a gravel bike or MTB. Actually, my first gravel bike was all road components (Ultegra).
Or, you're probably fine. I ride my gravel bike and MTB through some pretty dirty/mucky conditions on a regular basis. After I ride, I hose it off, wipe it down, and re-lube the chain. All good. My road bike gets the same treatment when it needs it. The components of a road bike aren't significantly more delicate than those of a gravel bike or MTB. Actually, my first gravel bike was all road components (Ultegra).
Likes For pepperbelly:
#4
Senior Member
Join Date: Jul 2008
Location: 25 miles northwest of Boston
Posts: 29,552
Bikes: Bottecchia Sprint, GT Timberline 29r, Marin Muirwoods 29er, Trek FX Alpha 7.0
Mentioned: 112 Post(s)
Tagged: 0 Thread(s)
Quoted: 5224 Post(s)
Liked 3,585 Times
in
2,344 Posts
sometimes I ride sandy areas & it can get kicked up on everything. a few years ago I added straw brushes to my cleaning kit. the kind of brushes ppl uses to clean their water bottle straws. took a while to find some that fit between the small links in the chains. not something I always do, not even annually. but when the needs arises, they are handy to have. when the chain gets mucky I dip the straw brushes in mineral spirits. I'm not going to spray a hose directly onto my chain links. a little splashing is OK
#5
I'm good to go!
Join Date: Jul 2017
Location: Mississippi
Posts: 15,002
Bikes: Tarmac Disc Comp Di2 - 2020
Mentioned: 51 Post(s)
Tagged: 0 Thread(s)
Quoted: 6198 Post(s)
Liked 4,814 Times
in
3,321 Posts
What's the worry? You might have to get a chain a hundred or so miles sooner? Even if you had to get one tomorrow, would that be a problem?
Likes For Iride01:
#6
Full Member
Join Date: Nov 2022
Location: California's capital
Posts: 467
Bikes: Litespeed Firenze, Spot Acme, Specialzed S Works Pro Race, Davidson Stiletto, Colnago Superissimo
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 133 Post(s)
Liked 304 Times
in
174 Posts
Seems like removing the chain, putting it in a closed container of cleaner, shaking the daylights out of it, rinsing and drying, lubing and replacing would rid it of any particles. Not knowing what minerals comprise the silt it's hard to guess if it would cause accelerated wear.
But it's not as though you were swamping for hours, and mtn bikers deal with this routinely and probably don't do more than a scrub and hose-off. OTOH now that we're in an era of $80 chains and $400 clusters I'm less of a mind to "use it up and toss it" and intermittently give my chains a complete clean off the bike. I appreciate the silence of a clean, lubed chain.
But it's not as though you were swamping for hours, and mtn bikers deal with this routinely and probably don't do more than a scrub and hose-off. OTOH now that we're in an era of $80 chains and $400 clusters I'm less of a mind to "use it up and toss it" and intermittently give my chains a complete clean off the bike. I appreciate the silence of a clean, lubed chain.
Likes For Rick_D:
#7
Senior Member
Join Date: Apr 2007
Posts: 6,764
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 1110 Post(s)
Liked 1,204 Times
in
761 Posts
sometimes I ride sandy areas & it can get kicked up on everything. a few years ago I added straw brushes to my cleaning kit. the kind of brushes ppl uses to clean their water bottle straws. took a while to find some that fit between the small links in the chains. not something I always do, not even annually. but when the needs arises, they are handy to have. when the chain gets mucky I dip the straw brushes in mineral spirits. I'm not going to spray a hose directly onto my chain links. a little splashing is OK
The ShelBroCo Bicycle Chain Cleaning System (sheldonbrown.com)
#8
Commuter
Join Date: Jun 2022
Location: SE Wisconsin, USA
Posts: 541
Bikes: Main Bikes: 2023 Trek Domane AL3, 2022 Aventon Level.2 eBike, 1972 Schwinn Varsity, 2024 Priority Apollo 11
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 238 Post(s)
Liked 323 Times
in
196 Posts
Yep, you're fine
That's all you can reasonably do.
One comment though, I wouldn't wait for it to dry from the hose-down, or you might find it rusty when you get back to oil it. Wipe the water off with a dry rag or paper towel and re-lube it on the spot.
You may want to hose off the pedal bearings too.
One comment though, I wouldn't wait for it to dry from the hose-down, or you might find it rusty when you get back to oil it. Wipe the water off with a dry rag or paper towel and re-lube it on the spot.
You may want to hose off the pedal bearings too.
#9
Cheerfully low end
Join Date: Jun 2020
Posts: 1,978
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 646 Post(s)
Liked 1,044 Times
in
667 Posts
I ride almost exclusively on crushed stone trails. They are either dusty, muddy or some of both. My bikes are always covered with dust or mud and stuff gets on the chain with every ride. Brush off the dirt and crud or wipe with a paper towel. Add some lube. It’ll be fine! 👍
Otto
Otto
Likes For ofajen:
#10
old newbie
Thread Starter
Join Date: Nov 2009
Location: Fort Worth, Texas
Posts: 866
Bikes: Specialized Roubaix
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 541 Post(s)
Liked 359 Times
in
182 Posts
That's all you can reasonably do.
One comment though, I wouldn't wait for it to dry from the hose-down, or you might find it rusty when you get back to oil it. Wipe the water off with a dry rag or paper towel and re-lube it on the spot.
You may want to hose off the pedal bearings too.
One comment though, I wouldn't wait for it to dry from the hose-down, or you might find it rusty when you get back to oil it. Wipe the water off with a dry rag or paper towel and re-lube it on the spot.
You may want to hose off the pedal bearings too.
If chain wear accelerates I will replace it sooner than expected. I was worried more about the sprockets.
Likes For pepperbelly:
#11
Senior Member
Join Date: May 2022
Location: USA - Southwest PA
Posts: 3,100
Bikes: Cannondale - Gary Fisher - Giant - Litespeed - Schwinn Paramount - Schwinn (lugged steel) - Trek OCLV
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 1401 Post(s)
Liked 1,886 Times
in
1,085 Posts
I ride almost exclusively on crushed stone trails. They are either dusty, muddy or some of both. My bikes are always covered with dust or mud and stuff gets on the chain with every ride. Brush off the dirt and crud or wipe with a paper towel. Add some lube. It’ll be fine! 👍
Otto
Otto
Swiffer cloth works great to remove the fine dry dust from the crushed stone trails and similar - much better than paper towel
like riding the crushed stone trails - but the dust can be a turnoff - so much that we avoid the crushed stone trails during dry periods … prefer to ride those types of trails when damp / not long after rain - as opposed to when dry / dusty and then just about everything is covered with fine dust after a ride
Last edited by t2p; 03-21-24 at 12:05 AM.
#12
Cheerfully low end
Join Date: Jun 2020
Posts: 1,978
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 646 Post(s)
Liked 1,044 Times
in
667 Posts
Swiffer cloth works great to remove the fine dry dust from the crushed stone trails and similar - much better than paper towel
like riding the crushed stone trails - but the dust can be a turnoff - so much that we avoid the crushed stone trails during dry periods … prefer to ride those types of trails when damp / not long after rain - as opposed to when dry / dusty and then just about everything is covered with fine dust after a ride
I only ride those trails (and connecting routes), to the point that my frame color preference is now based on how well a color matches the trail dust color. 😊
Otto
Likes For ofajen:
#13
SE Wis
Join Date: Apr 2005
Location: Milwaukee, WI
Posts: 10,517
Bikes: '68 Raleigh Sprite, '02 Raleigh C500, '84 Raleigh Gran Prix, '91 Trek 400, 2013 Novara Randonee, 1990 Trek 970
Mentioned: 40 Post(s)
Tagged: 0 Thread(s)
Quoted: 2747 Post(s)
Liked 3,401 Times
in
2,058 Posts
My experience with sandy silt where our river often overflows the trail is that stuff is slicker than ice when wet
Likes For dedhed:
#14
Senior Member
Join Date: May 2022
Location: USA - Southwest PA
Posts: 3,100
Bikes: Cannondale - Gary Fisher - Giant - Litespeed - Schwinn Paramount - Schwinn (lugged steel) - Trek OCLV
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 1401 Post(s)
Liked 1,886 Times
in
1,085 Posts
Likes For t2p:
#15
old newbie
Thread Starter
Join Date: Nov 2009
Location: Fort Worth, Texas
Posts: 866
Bikes: Specialized Roubaix
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 541 Post(s)
Liked 359 Times
in
182 Posts
It was wet very fine silt from nearby construction.
#16
Senior Member
In my experience, slippery mud is clay. Sand is small quartz grains. Crushed stone may be soft limestone, or hard granite. Clay and limestone are soft enough for the chain and gears to handle. Quartz and granite, on the contrary will eat the drive train.
YMMV
YMMV
Likes For Pratt:
#17
old newbie
Thread Starter
Join Date: Nov 2009
Location: Fort Worth, Texas
Posts: 866
Bikes: Specialized Roubaix
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 541 Post(s)
Liked 359 Times
in
182 Posts
This stuff was wet and light tan colored. It washed down from a construction site uphill from the trail. It was just fine silt. I managed to clean most of it but I missed some that had been sprayed up under the seat.