Do XT cassettes last longer?
#1
Newbie
Thread Starter
Join Date: Feb 2009
Posts: 74
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 33 Post(s)
Likes: 0
Liked 12 Times
in
9 Posts
Do XT cassettes last longer?
I run nine speed triple on a road bike. I'm keen to future proof my set up, so have bought spare derailleurs, shifters. What I haven't stocked up on is spare cassettes (or chains). There are still some XT M770 cassettes available. They are about double the price of available Sora (HG50?) cassettes. Will they last twice as long? Or are there any other reasons to pay the extra? My rear shifts are perfect at the moment, on a Sora cassette with M772 RD.
Thanks.
Thanks.
#2
Senior Member
Join Date: Jan 2009
Location: San Diego, CA
Posts: 3,673
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 837 Post(s)
Liked 1,061 Times
in
745 Posts
I run nine speed triple on a road bike. I'm keen to future proof my set up, so have bought spare derailleurs, shifters. What I haven't stocked up on is spare cassettes (or chains). There are still some XT M770 cassettes available. They are about double the price of available Sora (HG50?) cassettes. Will they last twice as long? Or are there any other reasons to pay the extra? My rear shifts are perfect at the moment, on a Sora cassette with M772 RD.
Thanks.
Thanks.
Last edited by Crankycrank; 10-11-21 at 12:37 PM.
Likes For Crankycrank:
#3
Senior Member
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656
Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!
Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,096 Times
in
742 Posts
A quick Google search turned up dozens of listings for 9-speed cassettes from Shimano, SRAM and a couple of lesser known brands in a variety of quality levels from HG50 up to Ultegra. Even Amazon lists them so I wouldn't worry about future supply problems. For that matter, even 7 and 8-speed cassettes are still fairly easy to find.
As to 9-speed chains, if you have problems finding them, 10-speed chains will work just fine on a 9-speed cassette. I've used 10-speed chains on an 8-speed cassette and it worked perfectly.
As to 9-speed chains, if you have problems finding them, 10-speed chains will work just fine on a 9-speed cassette. I've used 10-speed chains on an 8-speed cassette and it worked perfectly.
#4
Newbie
Thread Starter
Join Date: Feb 2009
Posts: 74
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 33 Post(s)
Likes: 0
Liked 12 Times
in
9 Posts
A quick Google search turned up dozens of listings for 9-speed cassettes from Shimano, SRAM and a couple of lesser known brands in a variety of quality levels from HG50 up to Ultegra. Even Amazon lists them so I wouldn't worry about future supply problems. For that matter, even 7 and 8-speed cassettes are still fairly easy to find.
As to 9-speed chains, if you have problems finding them, 10-speed chains will work just fine on a 9-speed cassette. I've used 10-speed chains on an 8-speed cassette and it worked perfectly.
As to 9-speed chains, if you have problems finding them, 10-speed chains will work just fine on a 9-speed cassette. I've used 10-speed chains on an 8-speed cassette and it worked perfectly.
#5
Guest
Join Date: Sep 2020
Posts: 2,888
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 1346 Post(s)
Liked 3,270 Times
in
1,439 Posts
That depends entirely on how you use and maintain it, but there's nothing inherently more durable about XT. They do claim that the pins behind the biggest cog can help prevent spoke damage in the event of an overshift.
#6
Method to My Madness
Join Date: Nov 2020
Location: Orange County, California
Posts: 3,662
Bikes: Trek FX 2, Cannondale Synapse, Cannondale CAAD4, Santa Cruz Stigmata GRX
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 1947 Post(s)
Liked 1,469 Times
in
1,018 Posts
#8
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,084
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4205 Post(s)
Liked 3,863 Times
in
2,311 Posts
Some basic understandings are due here. The steels used for cogs are chosen for their manufacturing ease and cost before any wear rate. For any significantly longer wear the steel in a specific cassette will need to be hardened and I don't know of any claim of this from any brand. What I do hear a lot is about the coatings on the steel. Oxide/bluing type finishes on the low cost and various harder coatings on the better stuff. These coatings are still softer then the grit that a chain gets coated with in time. And that's the heart of the issue. The abrasives that are grit and grime will wear any coating or base steel given enough neglect or miles. Think about using sand paper on the various cogs and name one that won't be scratched by that. The better cog coatings will aid the chain's smoothness a tiny bit, reduce engagement friction slightly until the coating is worn through. BTW these coatings are only scant ten thousandths to a a few thousandths thick and tend to be brittle so they can break down and flake off off with stress.
I consider cogs, like chains, rings, pads, and bar tape to be consumables (and rims too but others spend so much for their wheels that they can't get past the investment aspects). Sometimes I get lower cost stuff for myself and sometimes I splurge and get the fancy and lighter weight expensive stuff. But My eyes are open to what I am expecting. Andy
I consider cogs, like chains, rings, pads, and bar tape to be consumables (and rims too but others spend so much for their wheels that they can't get past the investment aspects). Sometimes I get lower cost stuff for myself and sometimes I splurge and get the fancy and lighter weight expensive stuff. But My eyes are open to what I am expecting. Andy
__________________
AndrewRStewart
AndrewRStewart
Last edited by Andrew R Stewart; 10-08-21 at 07:59 PM. Reason: late evening keyboard challenges
Likes For Andrew R Stewart:
#9
Newbie
Thread Starter
Join Date: Feb 2009
Posts: 74
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 33 Post(s)
Likes: 0
Liked 12 Times
in
9 Posts
Some basic understandings are due here. The steels used for cogs are chosen for their manufacturing ease and cost before any wear rate. For any significantly longer wear the steel in a specific cassette will need to be hardened and I don't know of any claim of this from any brand. What I do hear a lot is about the coatings on the steel. Oxide/bluing type finishes on the low cost and various harder coatings on the better stuff. These coatings are still softer then the grit that a chain gets coated with in time. And that's the heart of the issue. The abrasives that are grit and grime will wear any coating or base steel given enough neglect or miles. Think about using sand paper on the various cogs and name one that won't be scratched by that. The better cog coatings will aid the chain's smoothness a tiny bit, reduce engagement friction slightly and until the coating is worn through BTW these coatings are only scant ten thousandths to a a few thousandths thick and tens to be brittle so they can break down and flake off off with stress.
I consider cogs, like chains, rings, pads, and bar tape to be consumables (and rims too but others spend so much for their wheels that they can't get past the investment aspects). Sometimes I get lower cost stuff for myself and sometimes I splurge and get the fancy and lighter weight expensive stuff. But My eyes are open to what I am expecting. Andy
I consider cogs, like chains, rings, pads, and bar tape to be consumables (and rims too but others spend so much for their wheels that they can't get past the investment aspects). Sometimes I get lower cost stuff for myself and sometimes I splurge and get the fancy and lighter weight expensive stuff. But My eyes are open to what I am expecting. Andy
#10
Senior Member
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656
Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!
Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,096 Times
in
742 Posts
#11
Method to My Madness
Join Date: Nov 2020
Location: Orange County, California
Posts: 3,662
Bikes: Trek FX 2, Cannondale Synapse, Cannondale CAAD4, Santa Cruz Stigmata GRX
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 1947 Post(s)
Liked 1,469 Times
in
1,018 Posts
Doubtful.
When I went 1X conversion on my hybrid bike, I decided to replace my 8 speed 11-32 Altus CS-HG31 cassette to get the slightly different 11-30 gearing, and paid a few more dollars for an Alivio CS-HG51 which has a shinier finish than an Acera CS-HG41.
When I went 1X conversion on my hybrid bike, I decided to replace my 8 speed 11-32 Altus CS-HG31 cassette to get the slightly different 11-30 gearing, and paid a few more dollars for an Alivio CS-HG51 which has a shinier finish than an Acera CS-HG41.
Last edited by SoSmellyAir; 10-08-21 at 09:25 PM.
#12
Occam's Rotor
Join Date: Jul 2013
Posts: 7,248
Mentioned: 61 Post(s)
Tagged: 0 Thread(s)
Quoted: 2366 Post(s)
Liked 2,331 Times
in
1,164 Posts
#13
Occam's Rotor
Join Date: Jul 2013
Posts: 7,248
Mentioned: 61 Post(s)
Tagged: 0 Thread(s)
Quoted: 2366 Post(s)
Liked 2,331 Times
in
1,164 Posts
#14
working on my sandal tan
Join Date: Aug 2011
Location: CID
Posts: 22,629
Bikes: 1991 Bianchi Eros, 1964 Armstrong, 1988 Diamondback Ascent, 1988 Bianchi Premio, 1987 Bianchi Sport SX, 1980s Raleigh mixte (hers), All-City Space Horse (hers)
Mentioned: 98 Post(s)
Tagged: 0 Thread(s)
Quoted: 3871 Post(s)
Liked 2,568 Times
in
1,579 Posts
I run nine speed triple on a road bike. I'm keen to future proof my set up, so have bought spare derailleurs, shifters. What I haven't stocked up on is spare cassettes (or chains). There are still some XT M770 cassettes available. They are about double the price of available Sora (HG50?) cassettes. Will they last twice as long? Or are there any other reasons to pay the extra? My rear shifts are perfect at the moment, on a Sora cassette with M772 RD.
Thanks.
Thanks.
#15
Occam's Rotor
Join Date: Jul 2013
Posts: 7,248
Mentioned: 61 Post(s)
Tagged: 0 Thread(s)
Quoted: 2366 Post(s)
Liked 2,331 Times
in
1,164 Posts
I don't know if this is true for 9 speed, but for some of the 11 and 12 speed cassettes, the largest cogs are aluminum, so they are likely to be shorter lived.
#17
Disco Infiltrator
Join Date: May 2013
Location: Folsom CA
Posts: 13,446
Bikes: Stormchaser, Paramount, Tilt, Samba tandem
Mentioned: 72 Post(s)
Tagged: 0 Thread(s)
Quoted: 3126 Post(s)
Liked 2,105 Times
in
1,369 Posts
The coatings Andy mentioned aren’t really there for wear, for the most part. They are rust prevention, and gunk doesn’t stick as hard to glossy surfaces. So in that sense, yes, they help. They’re also prettier.
The best way to future proof your bike is… not to worry about that, it’s doomed. Premium 9 speed is a snapshot of 15-20 years ago.
The best way to future proof your bike is… not to worry about that, it’s doomed. Premium 9 speed is a snapshot of 15-20 years ago.
Last edited by Darth Lefty; 10-08-21 at 10:54 PM.
Likes For Darth Lefty: