Repair of 90's Rapidfire shifters
#1
Senior Member
Thread Starter
Repair of 90's Rapidfire shifters
Hello Everyone,
I am a long time volunteer at a local non-profit that repairs and gives away bikes. We receive quite a few 90's era ATB's with Shimano Rapidfire shifters that are gummed up and do not operate. I am looking for suggestions of what solution(s) to soak the shifters in (off the bike) that will dissolve the hardened beeswax -like old Shimano grease. So far I have been pretty successful soaking them for about 2 days in gasoline but I am not crazy about the residue left (or flammability). I have heard of using mineral spirits, acetone, brake fluid, etc... I would like to use something safe and if possible non harsh chemicals, I am open to any and all suggestions to solve this problem ! Thanks in advance.
I am a long time volunteer at a local non-profit that repairs and gives away bikes. We receive quite a few 90's era ATB's with Shimano Rapidfire shifters that are gummed up and do not operate. I am looking for suggestions of what solution(s) to soak the shifters in (off the bike) that will dissolve the hardened beeswax -like old Shimano grease. So far I have been pretty successful soaking them for about 2 days in gasoline but I am not crazy about the residue left (or flammability). I have heard of using mineral spirits, acetone, brake fluid, etc... I would like to use something safe and if possible non harsh chemicals, I am open to any and all suggestions to solve this problem ! Thanks in advance.
Likes For jacksbike:
#2
Mad bike riding scientist
Join Date: Nov 2004
Location: Denver, CO
Posts: 27,378
Bikes: Some silver ones, a red one, a black and orange one, and a few titanium ones
Mentioned: 152 Post(s)
Tagged: 1 Thread(s)
Quoted: 6225 Post(s)
Liked 4,228 Times
in
2,372 Posts
Hello Everyone,
I am a long time volunteer at a local non-profit that repairs and gives away bikes. We receive quite a few 90's era ATB's with Shimano Rapidfire shifters that are gummed up and do not operate. I am looking for suggestions of what solution(s) to soak the shifters in (off the bike) that will dissolve the hardened beeswax -like old Shimano grease. So far I have been pretty successful soaking them for about 2 days in gasoline but I am not crazy about the residue left (or flammability). I have heard of using mineral spirits, acetone, brake fluid, etc... I would like to use something safe and if possible non harsh chemicals, I am open to any and all suggestions to solve this problem ! Thanks in advance.
I am a long time volunteer at a local non-profit that repairs and gives away bikes. We receive quite a few 90's era ATB's with Shimano Rapidfire shifters that are gummed up and do not operate. I am looking for suggestions of what solution(s) to soak the shifters in (off the bike) that will dissolve the hardened beeswax -like old Shimano grease. So far I have been pretty successful soaking them for about 2 days in gasoline but I am not crazy about the residue left (or flammability). I have heard of using mineral spirits, acetone, brake fluid, etc... I would like to use something safe and if possible non harsh chemicals, I am open to any and all suggestions to solve this problem ! Thanks in advance.
Direct lubrication to the pin that the pawl is on and make sure it can move back and forth freely. Light oil will do to lubricate it.
Here's the
__________________
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
#3
Senior Member
Join Date: Jan 2010
Location: se MIch.
Posts: 2,316
Bikes: 1938 claud butler,1983 Basso,teledyne titan,teocali super,nrs,1993 stumpjumper fsr,Paramountain,Paramount Buell(sold),4 banger,Zaskar LE,Colnago Master Ibex MTB,1987ish,.etc....
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 805 Post(s)
Liked 2,990 Times
in
1,502 Posts
rapidfires/
if above video isn't fixing the issue you can further dismantle the unit.there are 3 spring attachment devises that all need to line up on reassembly.when apart you can physically remove the pawl off the shaft & thoroughly clean the gunk off.you may get lucky by using a fast drying spray solvent like carb gumout with the precise nozzle but there may still be gunk within.my '94 stx shifters have needed 3 cleanings-the gunk is very stubborn at times.
#4
Bad example
Join Date: Nov 2015
Location: Seattle and Reims
Posts: 3,095
Bikes: Peugeot: AO-8 1973, PA-10 1971, PR-10 1973, Sante 1988; Masi Gran Criterium 1975, Stevenson Tourer 1980, Stevenson Criterium 1981, Schwinn Paramount 1972, Rodriguez 2006, Gitane Federal ~1975, Holdsworth Pro, Follis 172 ~1973, Bianchi '62
Mentioned: 36 Post(s)
Tagged: 0 Thread(s)
Quoted: 838 Post(s)
Liked 241 Times
in
108 Posts
Soaking the whole shifter isn't the way to fix the problem. You need a more targeted approach. The problem is that the pawl that moves a gear forward tends to get sticky. Spraying lubricant into the shifter housing may fix the problem but if you take the cover off the shifter you should be able to see the pawl that is the problem.
__________________
Keeping Seattle’s bike shops in business since 1978
Keeping Seattle’s bike shops in business since 1978
#5
Bike Sorceress
Join Date: Apr 2008
Location: MPLS
Posts: 761
Bikes: Yes
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 62 Post(s)
Liked 116 Times
in
66 Posts
Typically I start by removing any covers that can be removed, spray in some Clean-Streak, isopropyl alcohol, or other degreaser into the shifter, find the stuck pawls and move them back and forth till they start working properly, use an air gun to spray out the degreaser and bits of old grease, then relubricate with Tri-Flow or Dri-Slide. Gets most shifters working fine again.
There are a few models that might not be worth the time, either because the above method hasn't had a great success rate on them, like 7 speed Deore LX M560, and any of the early 90's models that have two tiny finger-like pawls right next to each other, or because they work so poorly even when they aren't gummed up, such as Acera X ST-M290 or Nexave ST-T300.
There are a few models that might not be worth the time, either because the above method hasn't had a great success rate on them, like 7 speed Deore LX M560, and any of the early 90's models that have two tiny finger-like pawls right next to each other, or because they work so poorly even when they aren't gummed up, such as Acera X ST-M290 or Nexave ST-T300.
#6
SE Wis
Join Date: Apr 2005
Location: Milwaukee, WI
Posts: 10,524
Bikes: '68 Raleigh Sprite, '02 Raleigh C500, '84 Raleigh Gran Prix, '91 Trek 400, 2013 Novara Randonee, 1990 Trek 970
Mentioned: 40 Post(s)
Tagged: 0 Thread(s)
Quoted: 2750 Post(s)
Liked 3,406 Times
in
2,061 Posts
#7
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,102
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4214 Post(s)
Liked 3,891 Times
in
2,322 Posts
Typically I start by removing any covers that can be removed, spray in some Clean-Streak, isopropyl alcohol, or other degreaser into the shifter, find the stuck pawls and move them back and forth till they start working properly, use an air gun to spray out the degreaser and bits of old grease, then relubricate with Tri-Flow or Dri-Slide. Gets most shifters working fine again.
There are a few models that might not be worth the time, either because the above method hasn't had a great success rate on them, like 7 speed Deore LX M560, and any of the early 90's models that have two tiny finger-like pawls right next to each other, or because they work so poorly even when they aren't gummed up, such as Acera X ST-M290 or Nexave ST-T300.
There are a few models that might not be worth the time, either because the above method hasn't had a great success rate on them, like 7 speed Deore LX M560, and any of the early 90's models that have two tiny finger-like pawls right next to each other, or because they work so poorly even when they aren't gummed up, such as Acera X ST-M290 or Nexave ST-T300.
I do much the same cleaning, sometimes working the pawls with a pick to help the dissolving of the gummy grease in the pivot. Where i differ is in the lube after free pawl movement. I like oils with a swipe of grease on top after working in the thin then thick oils. Andy
__________________
AndrewRStewart
AndrewRStewart
Likes For Andrew R Stewart:
#8
Senior Member
Join Date: Mar 2021
Location: SoCal
Posts: 2,339
Bikes: Cuevas Custom, Cimmaron, 1988 "Pinalized Rockma", 1984 Trek 510, Moulton custom touring, Raleigh Competition GS, Bridgestone Mb-2 & 3, 1980's Peugeot - US, City, & Canyon Express (6)
Mentioned: 27 Post(s)
Tagged: 0 Thread(s)
Quoted: 1120 Post(s)
Liked 3,810 Times
in
1,866 Posts
#9
Cantilever believer
Join Date: Nov 2021
Location: Phoenix, AZ
Posts: 1,594
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 545 Post(s)
Liked 1,877 Times
in
847 Posts
Thanks for the tag.
My experience has been that WD-40 and Clean Streak are only temporary fixes. If you really want to get those types of shifters working again, here is the method I use for rather good success:https://www.bikeforums.net/bicycle-m...l#post23196306
My experience has been that WD-40 and Clean Streak are only temporary fixes. If you really want to get those types of shifters working again, here is the method I use for rather good success:https://www.bikeforums.net/bicycle-m...l#post23196306
__________________
Richard C. Moeur, PE - Phoenix AZ, USA
https://www.richardcmoeur.com/bikestuf.html
Richard C. Moeur, PE - Phoenix AZ, USA
https://www.richardcmoeur.com/bikestuf.html
Likes For RCMoeur:
#10
Senior Member
Join Date: Dec 2008
Location: Pioneer Valley
Posts: 1,040
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 342 Post(s)
Liked 766 Times
in
399 Posts
All good advice above. One thing I’ll sometimes do before degreaser and lubricant is to flush the shifter with boiling water. This can work wonders for loosening up that hardened grease.
#11
Senior Member
Join Date: Feb 2012
Location: Golden, CO and Tucson, AZ
Posts: 2,842
Bikes: 2012 Specialized Elite Disc, 1983 Trek 520
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 678 Post(s)
Liked 744 Times
in
433 Posts
Ditto all the above. Dental picks are a big help--my dentist gives me his old ones when I ask. And I'll add, definitely stay away from the gasoline!
And kudos for volunteering at the nonprofit. Keep up the great work. It's how I enjoy spending a good part of my time. Freeing up stuck shifters is a big part of the work, and the reason many of them get donated.
And kudos for volunteering at the nonprofit. Keep up the great work. It's how I enjoy spending a good part of my time. Freeing up stuck shifters is a big part of the work, and the reason many of them get donated.
#12
Droid on a mission
Join Date: May 2018
Location: Palm Coast, FL
Posts: 1,006
Bikes: Diamondback Wildwood Classic
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 317 Post(s)
Liked 281 Times
in
195 Posts
Our tried and true method is to remove the covers, saturate the mechanisms with PB Blaster, working the shifter and pawls for a few minutes. Finally follow up with a squirt or two of the 3-IN-One lightweight penetrating oil. Work the shifter again and magic. This stuff is gold for these shifters.
Available at Home Depot https://www.homedepot.com/p/3-IN-ONE...0015/300719551
Available at Home Depot https://www.homedepot.com/p/3-IN-ONE...0015/300719551
__________________
JoeTBM (The Bike Man) - I'm a black & white type of guy, the only gray in my life is the hair on my head
www.TheBikeMenOfFlaglerCounty.com
JoeTBM (The Bike Man) - I'm a black & white type of guy, the only gray in my life is the hair on my head
www.TheBikeMenOfFlaglerCounty.com
Last edited by JoeTBM; 04-12-24 at 03:33 AM.
#13
Droid on a mission
Join Date: May 2018
Location: Palm Coast, FL
Posts: 1,006
Bikes: Diamondback Wildwood Classic
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 317 Post(s)
Liked 281 Times
in
195 Posts
Hello Everyone,
I am a long time volunteer at a local non-profit that repairs and gives away bikes. We receive quite a few 90's era ATB's with Shimano Rapidfire shifters that are gummed up and do not operate. I am looking for suggestions of what solution(s) to soak the shifters in (off the bike) that will dissolve the hardened beeswax -like old Shimano grease. So far I have been pretty successful soaking them for about 2 days in gasoline but I am not crazy about the residue left (or flammability). I have heard of using mineral spirits, acetone, brake fluid, etc... I would like to use something safe and if possible non harsh chemicals, I am open to any and all suggestions to solve this problem ! Thanks in advance.
I am a long time volunteer at a local non-profit that repairs and gives away bikes. We receive quite a few 90's era ATB's with Shimano Rapidfire shifters that are gummed up and do not operate. I am looking for suggestions of what solution(s) to soak the shifters in (off the bike) that will dissolve the hardened beeswax -like old Shimano grease. So far I have been pretty successful soaking them for about 2 days in gasoline but I am not crazy about the residue left (or flammability). I have heard of using mineral spirits, acetone, brake fluid, etc... I would like to use something safe and if possible non harsh chemicals, I am open to any and all suggestions to solve this problem ! Thanks in advance.
__________________
JoeTBM (The Bike Man) - I'm a black & white type of guy, the only gray in my life is the hair on my head
www.TheBikeMenOfFlaglerCounty.com
JoeTBM (The Bike Man) - I'm a black & white type of guy, the only gray in my life is the hair on my head
www.TheBikeMenOfFlaglerCounty.com
#14
Junior Member
Join Date: Mar 2024
Location: San Diego
Posts: 153
Bikes: Paramount Track Bike, Colnago Super, Santana Tandems (1995 & 2007), Gary Fisher Piranha, Trek Wahoo, Bianchi Track Bike, a couple of Honda mountain bikes
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 73 Post(s)
Liked 32 Times
in
21 Posts
Hello Everyone,
I am a long time volunteer at a local non-profit that repairs and gives away bikes. We receive quite a few 90's era ATB's with Shimano Rapidfire shifters that are gummed up and do not operate. I am looking for suggestions of what solution(s) to soak the shifters in (off the bike) that will dissolve the hardened beeswax -like old Shimano grease. So far I have been pretty successful soaking them for about 2 days in gasoline but I am not crazy about the residue left (or flammability). I have heard of using mineral spirits, acetone, brake fluid, etc... I would like to use something safe and if possible non harsh chemicals, I am open to any and all suggestions to solve this problem ! Thanks in advance.
I am a long time volunteer at a local non-profit that repairs and gives away bikes. We receive quite a few 90's era ATB's with Shimano Rapidfire shifters that are gummed up and do not operate. I am looking for suggestions of what solution(s) to soak the shifters in (off the bike) that will dissolve the hardened beeswax -like old Shimano grease. So far I have been pretty successful soaking them for about 2 days in gasoline but I am not crazy about the residue left (or flammability). I have heard of using mineral spirits, acetone, brake fluid, etc... I would like to use something safe and if possible non harsh chemicals, I am open to any and all suggestions to solve this problem ! Thanks in advance.
__________________
Cheers, Mike
Cheers, Mike