How much am I over oiling?
#1
Full Member
Thread Starter
How much am I over oiling?
I have two White freewheel’s now.
I am always worried about getting them shark toothed, so I oil every time I ride. I use that wet lube that comes in a black bottle with a green label. Forget it’s name but you see it everywhere. Finish line, that’s it.
After a while, my bike started to look like one of those old cars with bad gaskets. The whole bottom frame was greasy.
I do my healthy 20 miles a day, not fast , but lots of hills. How much should I be oiling? What amount of drops and how often?
I am always worried about getting them shark toothed, so I oil every time I ride. I use that wet lube that comes in a black bottle with a green label. Forget it’s name but you see it everywhere. Finish line, that’s it.
After a while, my bike started to look like one of those old cars with bad gaskets. The whole bottom frame was greasy.
I do my healthy 20 miles a day, not fast , but lots of hills. How much should I be oiling? What amount of drops and how often?
Likes For Colorado Kid:
#3
Zip tie Karen
Join Date: Aug 2009
Location: Fair Oaks Ranch, TX
Posts: 7,004
Bikes: '13 Motobecane Fantom29 HT, '16 Motobecane Turino Pro Disc, '18 Velobuild VB-R-022, '21 Tsunami SNM-100
Mentioned: 26 Post(s)
Tagged: 0 Thread(s)
Quoted: 1465 Post(s)
Liked 1,542 Times
in
806 Posts
Both your chain and your freewheel should appear clean and dry. So, after you lubricate each link and work the lube in a bit, you must wipe down the chain thoroughly. That means no visible lubricant on the outer plates, on the rollers, on your chainring or on your freewheel teeth. Spend 5% of your time applying the drop-by-drop lube to the roller/pin/plate joint and 95% of your time wiping clean afterwards.
And you don't need to lubricate every time that you ride. Think about what you are doing. Want to prevent wear? Then don't create a slurry of oil and grit through which you run your chain and cogs. What do you think that is accomplishing? Accelerating wear? Most likely.
Keep it clean and keep it quiet. The rest is irrational.
And you don't need to lubricate every time that you ride. Think about what you are doing. Want to prevent wear? Then don't create a slurry of oil and grit through which you run your chain and cogs. What do you think that is accomplishing? Accelerating wear? Most likely.
Keep it clean and keep it quiet. The rest is irrational.
Likes For Phil_gretz:
#4
Senior Member
I agree with Phil Gretz. Generally less is best. Precision application versus slobber it all over the chain is better.
#5
Cheerfully low end
Join Date: Jun 2020
Posts: 1,978
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 646 Post(s)
Liked 1,044 Times
in
667 Posts
Both your chain and your freewheel should appear clean and dry. So, after you lubricate each link and work the lube in a bit, you must wipe down the chain thoroughly. That means no visible lubricant on the outer plates, on the rollers, on your chainring or on your freewheel teeth. Spend 5% of your time applying the drop-by-drop lube to the roller/pin/plate joint and 95% of your time wiping clean afterwards.
And you don't need to lubricate every time that you ride. Think about what you are doing. Want to prevent wear? Then don't create a slurry of oil and grit through which you run your chain and cogs. What do you think that is accomplishing? Accelerating wear? Most likely.
Keep it clean and keep it quiet. The rest is irrational.
And you don't need to lubricate every time that you ride. Think about what you are doing. Want to prevent wear? Then don't create a slurry of oil and grit through which you run your chain and cogs. What do you think that is accomplishing? Accelerating wear? Most likely.
Keep it clean and keep it quiet. The rest is irrational.
Otto
Likes For ofajen:
#6
Old fart
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,790
Bikes: Several, mostly not name brands.
Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3590 Post(s)
Liked 3,401 Times
in
1,935 Posts
An over-oiled drivetrain collects grit and can actually accelerate wear. As others mentioned, less can be better. A precision oiler, with a small drop on each chain roller (but not the side plates) followed by a wipe-down to get rid of excess works for me. Don't clean/reoil until the chain/sprockets are noticeably dirty, or when the chain gets noisy.
Likes For JohnDThompson:
#7
Super-duper Genius
Join Date: Aug 2016
Location: Muskrat Springs, Utah
Posts: 1,713
Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
Quoted: 768 Post(s)
Liked 984 Times
in
508 Posts
I like to clean my chainrings and cogs fairly often too. I don't use any special brushes or machines for this, usually just an old cotton t-shirt. Friends often comment on my sparkling drivetrain. I tell them "It's like a sickness, I can't help it."
#8
Guest
Join Date: Sep 2020
Posts: 2,888
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 1346 Post(s)
Liked 3,270 Times
in
1,439 Posts
Clean the chain regularly and well, and you can use less lube. +1 on the Boeshield.
#9
Zip tie Karen
Join Date: Aug 2009
Location: Fair Oaks Ranch, TX
Posts: 7,004
Bikes: '13 Motobecane Fantom29 HT, '16 Motobecane Turino Pro Disc, '18 Velobuild VB-R-022, '21 Tsunami SNM-100
Mentioned: 26 Post(s)
Tagged: 0 Thread(s)
Quoted: 1465 Post(s)
Liked 1,542 Times
in
806 Posts
Premature Wear From Overoiling
Close up of FD-4703 Cage Wear (pencil point)
This was today's customer who frequently oils his chain, but rides on trail and in dirt. The oily sludge helped his chain to cut through his FD cage in only 3 years. I had warned him last year (and the year prior ) to keep the chain drier and wiped clean. Oh well.
Likes For Phil_gretz:
#10
Senior Member
Don't treat your drive chain like the Tin Man. It just gets dirtier a lot faster.