homemade rim strip easy
#1
Full Member
Thread Starter
Join Date: Dec 2006
Posts: 428
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 6 Post(s)
Likes: 0
Liked 4 Times
in
4 Posts
homemade rim strip easy
I was rehabbing a really old bike yesterday and was out of rim strips and didn't feel like running to the bike store so I made one. Took about 10 minutes. I took and old innertube which most people have or can get free from any bike shop. I hooked it to my vise so I could easily stretch it out and cut it. Then I cut a long skinny strip from it being careful to follow the seam lines so it was straight. Then I stretched the strip along the wheel to get correct length allowing 1" extra. I took some thread and sewed the overlapping one inch with a few quick stitches and punched a valve hole with my paper punch. Voila worked fine and stronger than the flimsy usual rim strips.
Likes For cmcanulty:
#2
Senior Member
Join Date: Apr 2009
Location: New Rochelle, NY
Posts: 38,725
Bikes: too many bikes from 1967 10s (5x2)Frejus to a Sumitomo Ti/Chorus aluminum 10s (10x2), plus one non-susp mtn bike I use as my commuter
Mentioned: 140 Post(s)
Tagged: 1 Thread(s)
Quoted: 5792 Post(s)
Liked 2,582 Times
in
1,432 Posts
I guess we all define easy differently.
If I need rim strips or tape, I make the effort to hike upstairs to the bathroom, open the cabinet and swipe the roll of cloth surgical tape from the first aid supply.
The hardest part is remembering to replace it.
If I need rim strips or tape, I make the effort to hike upstairs to the bathroom, open the cabinet and swipe the roll of cloth surgical tape from the first aid supply.
The hardest part is remembering to replace it.
__________________
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
Likes For FBinNY:
#3
Senior Member
Join Date: Dec 2010
Location: northern Deep South
Posts: 8,904
Bikes: Fuji Touring, Novara Randonee
Mentioned: 36 Post(s)
Tagged: 0 Thread(s)
Quoted: 2604 Post(s)
Liked 1,933 Times
in
1,213 Posts
I'll give O.P. cheap, but I have to agree with FBinNY on easy.
Really easy would be having the spare rim tape float up to the top of my spare parts box when I need it.
Really easy would be having the spare rim tape float up to the top of my spare parts box when I need it.
Likes For pdlamb:
#4
señor miembro
Join Date: Dec 2018
Location: Pac NW
Posts: 6,625
Bikes: '70s - '80s Campagnolo
Mentioned: 92 Post(s)
Tagged: 0 Thread(s)
Quoted: 3889 Post(s)
Liked 6,488 Times
in
3,211 Posts
Rubber is too bulky for some tight fitting tires. I use two layers of 10mm kapton tape from eBay. Super inexpensive.
Likes For SurferRosa:
#5
Senior Member
Join Date: Jul 2013
Location: Missouri
Posts: 2,690
Bikes: Giant Propel, Cannondale SuperX, Univega Alpina Ultima
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 672 Post(s)
Liked 417 Times
in
249 Posts
Rim strips are cheap to begin with. I'd rather spring for an extra bick or two, be able to thrown them on in 10 seconds and not worry about flatting because my homemade strip gave up the ghost at an inopportune time.
__________________
Formerly fastest rider in the grupetto, currently slowest guy in the peloton
Formerly fastest rider in the grupetto, currently slowest guy in the peloton
Likes For bbbean:
#6
Senior Member
Join Date: Jul 2015
Location: NW Oregon
Posts: 2,975
Bikes: !982 Trek 930R Custom, Diamondback ascent with SERIOUS updates, Fuji Team Pro CF and a '09 Comencal Meta 5.5
Mentioned: 15 Post(s)
Tagged: 1 Thread(s)
Quoted: 1299 Post(s)
Liked 739 Times
in
534 Posts
one problem with using an inner tube as a rim band... Spokes poke holes in INNER TUBES, which is why we should all install Actual Rim strips.... or Medical bandage tape...
Likes For maddog34:
#7
Senior Member
Join Date: Mar 2022
Location: Missoula MT
Posts: 1,767
Bikes: Handsome xoxo, Serotta atx, Canyon Endurace CF8
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 904 Post(s)
Liked 1,899 Times
in
849 Posts
back in my day we used packing tape. I still am using a wheel from the early 90's that has had the same piece of packing tape on it since probably 1993.
#8
bOsscO
Join Date: May 2006
Location: Vancouver
Posts: 746
Bikes: 2024 Spec Crux, 2015 Norco Search S1, 93 Mongoose IBOC COMP
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 296 Post(s)
Liked 355 Times
in
212 Posts
I've used red electricians tape with good success. Not sure if it's stronger than standard black electricians tape...
#9
Senior Member
Join Date: Apr 2011
Location: Maryland, USA
Posts: 2,442
Bikes: Drysdale/Gitane/Zeus/Masi/Falcon/Palo Alto/Raleigh/Legnano
Mentioned: 34 Post(s)
Tagged: 0 Thread(s)
Quoted: 987 Post(s)
Liked 641 Times
in
407 Posts
+1 but I now have three different widths of Kapton tape for various rims... it adds up. Works great, however.
__________________
Larry:1958 Drysdale, 1961 Gitane Gran Sport, 1974 Zeus track, 1988 Masi Gran Corsa, 1974 Falcon, 1980 Palo Alto, 1973 Raleigh Gran Sport, 1974 Legnano. Susan: 1976 Windsor Profesional.
Larry:1958 Drysdale, 1961 Gitane Gran Sport, 1974 Zeus track, 1988 Masi Gran Corsa, 1974 Falcon, 1980 Palo Alto, 1973 Raleigh Gran Sport, 1974 Legnano. Susan: 1976 Windsor Profesional.
Likes For tiger1964:
#10
Sr Member on Sr bikes
Likes For _ForceD_:
#11
Senior Member
Join Date: Apr 2011
Posts: 7,067
Mentioned: 41 Post(s)
Tagged: 0 Thread(s)
Quoted: 4409 Post(s)
Liked 1,566 Times
in
1,028 Posts
I cover every spoke hole with a Tricot-Mesh Band Aid™.
#12
Senior Member
Join Date: May 2010
Location: Bastrop Texas
Posts: 4,481
Bikes: Univega, Peu P6, Peu PR-10, Ted Williams, Peu UO-8, Peu UO-18 Mixte, Peu Dolomites
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 967 Post(s)
Liked 1,631 Times
in
1,047 Posts
That's allot of work. Its gonna work well...
I use High Temp Wiring Loom Harness Self-Adhesive Felt Cloth Electrical Tape (Amazon). Its cheap. I keep several rolls in the beer frig and no longer worry about having the right size rim strip.
It also works good for Bar Tape.
Man... I am such a cheap bastard too...
I use High Temp Wiring Loom Harness Self-Adhesive Felt Cloth Electrical Tape (Amazon). Its cheap. I keep several rolls in the beer frig and no longer worry about having the right size rim strip.
It also works good for Bar Tape.
Man... I am such a cheap bastard too...
__________________
No matter where you're at... There you are... Δf:=f(1/2)-f(-1/2)
No matter where you're at... There you are... Δf:=f(1/2)-f(-1/2)
#13
Senior Member
Join Date: Jan 2013
Posts: 2,681
Bikes: too many sparkly Italians, some sweet Americans and a couple interesting Japanese
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 569 Post(s)
Liked 584 Times
in
410 Posts
Never had a problem with two layers of cheap 10mm kapton tape which stays in my bike tool box.
#14
Senior Member
Join Date: Jul 2006
Location: San Jose (Willow Glen) Ca
Posts: 9,847
Bikes: Kirk Custom JK Special, '84 Team Miyata,(dura ace old school) 80?? SR Semi-Pro 600 Arabesque
Mentioned: 106 Post(s)
Tagged: 0 Thread(s)
Quoted: 2338 Post(s)
Liked 2,827 Times
in
1,543 Posts
I am still a velox cloth tape only guy for tubed setups
__________________
Life is too short not to ride the best bike you have, as much as you can
(looking for Torpado Super light frame/fork or for Raleigh International frame fork 58cm)
Life is too short not to ride the best bike you have, as much as you can
(looking for Torpado Super light frame/fork or for Raleigh International frame fork 58cm)
Likes For squirtdad:
#15
Expired Member
Join Date: Jun 2007
Location: TN
Posts: 11,547
Mentioned: 37 Post(s)
Tagged: 0 Thread(s)
Quoted: 3674 Post(s)
Liked 5,437 Times
in
2,763 Posts
I'm with maddog on this. The inner tube might look the part but there's nothing to keep it from poking into the spoke hole like ... an inner tube.
Likes For shelbyfv:
#16
Senior Member
Join Date: May 2005
Location: SFBay
Posts: 2,334
Bikes: n, I would like n+1
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 127 Post(s)
Likes: 0
Liked 133 Times
in
108 Posts
While I don’t prefer them, I’ve used a lot of rubber rim strips in the past. They aren’t much different than a tube section. They also fail for the same reason, but take several years to do so unless your spokes are too long. Other than Velox I’ve used several kinds of tape, generally without issue. It’s even easier on double walled rims where you just have to bridge the holes.
#18
Hello
Fiberglass Filament tape
To the OP, Kudos, for a low/no budget solution, and making things worth, with what you got.
#19
Rhapsodic Laviathan
I've had wheels where the previous owner used duct tape. I usually use electrical tape in a quick need of a rim strip. I was at the co-op last month and they didn't have any, so I used a rubber rim strip on top of the rubber rim strip on one wheel.
#20
Senior Member
Join Date: Jan 2009
Location: San Diego, CA
Posts: 3,674
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 839 Post(s)
Liked 1,062 Times
in
746 Posts
Yes to packing tape (with fiberglass filament). It has no stretch. Is, latitudinally tear resistant. Buy a wide roll as it is easy to tear straight longitudinally, so that one roll serves different rim bed widths (perfect custom width every time).
To the OP, Kudos, for a low/no budget solution, and making things worth, with what you got.
To the OP, Kudos, for a low/no budget solution, and making things worth, with what you got.
#21
Cantilever believer
Join Date: Nov 2021
Location: Phoenix, AZ
Posts: 1,565
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 536 Post(s)
Liked 1,839 Times
in
832 Posts
At Recycle Your Bicycle, we go through rim strips by the hundreds in just one weekend, and we just heard our distributor is out of stock on some sizes UFN.
I've tried making rim strips out of old (next size down) tubes, but my experience in trying to cut or punch a Schrader-size hole without creating a plane of weakness that eventually tears has not been good. We can go to the ol' "3 loops of inexpensive electrician's tape", but were hoping there might be a better option. And no, our budget is nowhere near that which would allow the use of "real" cloth rim tape for hundreds of bikes.
Do you use the 3/5", 3/4", or 1" width? The 3/4" (18 mm) looks like it would be the most useful width. By my calculations, we could do about eight 26" rims per roll.
I've tried making rim strips out of old (next size down) tubes, but my experience in trying to cut or punch a Schrader-size hole without creating a plane of weakness that eventually tears has not been good. We can go to the ol' "3 loops of inexpensive electrician's tape", but were hoping there might be a better option. And no, our budget is nowhere near that which would allow the use of "real" cloth rim tape for hundreds of bikes.
Do you use the 3/5", 3/4", or 1" width? The 3/4" (18 mm) looks like it would be the most useful width. By my calculations, we could do about eight 26" rims per roll.
__________________
Richard C. Moeur, PE - Phoenix AZ, USA
https://www.richardcmoeur.com/bikestuf.html
Richard C. Moeur, PE - Phoenix AZ, USA
https://www.richardcmoeur.com/bikestuf.html
Likes For JanMM:
#23
Passista
Join Date: Jul 2005
Posts: 7,599
Bikes: 1998 Pinarello Asolo, 1992 KHS Montaña pro, 1980 Raleigh DL-1, IGH Hybrid, IGH Utility
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 868 Post(s)
Liked 721 Times
in
396 Posts
BITD we used to make rim strips with inner tubes, gluing the ends instead of sewing. Worked OK on single wall rims/low pressure tires, but not on double wall/high pressure, as the tube would force the strip into the spoke holes.
#24
Friendship is Magic
Join Date: Nov 2010
Location: Sacramento, CA
Posts: 22,985
Bikes: old ones
Mentioned: 304 Post(s)
Tagged: 0 Thread(s)
Quoted: 26425 Post(s)
Liked 10,381 Times
in
7,209 Posts
At Recycle Your Bicycle, we go through rim strips by the hundreds in just one weekend, and we just heard our distributor is out of stock on some sizes UFN.
I've tried making rim strips out of old (next size down) tubes, but my experience in trying to cut or punch a Schrader-size hole without creating a plane of weakness that eventually tears has not been good. We can go to the ol' "3 loops of inexpensive electrician's tape", but were hoping there might be a better option. And no, our budget is nowhere near that which would allow the use of "real" cloth rim tape for hundreds of bikes.
Do you use the 3/5", 3/4", or 1" width? The 3/4" (18 mm) looks like it would be the most useful width. By my calculations, we could do about eight 26" rims per roll.
I've tried making rim strips out of old (next size down) tubes, but my experience in trying to cut or punch a Schrader-size hole without creating a plane of weakness that eventually tears has not been good. We can go to the ol' "3 loops of inexpensive electrician's tape", but were hoping there might be a better option. And no, our budget is nowhere near that which would allow the use of "real" cloth rim tape for hundreds of bikes.
Do you use the 3/5", 3/4", or 1" width? The 3/4" (18 mm) looks like it would be the most useful width. By my calculations, we could do about eight 26" rims per roll.
...Kapton tape is pretty cheap, and it comes in various widths, in bulk rolls. I used to use Velox, but Kapton tape is cheaper, and it works a little better.
__________________
Likes For 3alarmer:
#25
Senior Member
Join Date: Oct 2014
Location: Portland, OR
Posts: 12,906
Bikes: (2) ti TiCycles, 2007 w/ triple and 2011 fixed, 1979 Peter Mooney, ~1983 Trek 420 now fixed and ~1973 Raleigh Carlton Competition gravel grinder
Mentioned: 129 Post(s)
Tagged: 0 Thread(s)
Quoted: 4806 Post(s)
Liked 3,932 Times
in
2,557 Posts
That inner tube strip might expand into the spoke holes in box section rims. I thought the rim strip's job was to prevent that. (Big fan of the Velox strips and their shelf life seems to be near forever so I have no excuse for not being stocked up. Except during COVID, choices were so slim I bought wide rolls knowing I was going to slice them to size with a sharp knife.)