No Schrader to Presta adaptor
#1
Senior Member
Thread Starter
Join Date: May 2016
Posts: 3,947
Bikes: Trek 1100 road bike, Roadmaster gravel/commuter/beater mountain bike
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 2281 Post(s)
Liked 1,710 Times
in
936 Posts
No Schrader to Presta adaptor
The rim on my rear wheel started cracking apart, so I got a new wheel. Unfortunately the new wheel is drilled for Schrader valve stems instead of the Presta stems which I use. I know they make adapters to fit in the holes, but I won't be able to get back to the bike shop for a while. So what I did was screw one of the flat Presta nuts all the way down on the stem before inserting it through the hole, then another one on the outside like normal. Is there any issue in doing this, if even temporarily? I think this is a better solution than not putting anything on the inside part of the stem. I run 90 PSI in my tires so I would be afraid the stems would blow out if I didn't have anything holding them back.
#2
Senior Member
Join Date: Mar 2011
Posts: 3,096
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 1034 Post(s)
Liked 1,292 Times
in
744 Posts
Then have them delivered to your door.
https://www.amazon.com/Quad-Wheels-M...-23&th=1&psc=1
Or rubber grommet style: https://www.amazon.com/Pack-Schrader...%3D%3D&sr=8-21
https://www.amazon.com/Quad-Wheels-M...-23&th=1&psc=1
Or rubber grommet style: https://www.amazon.com/Pack-Schrader...%3D%3D&sr=8-21
Likes For phughes:
#3
Senior Member
Join Date: Jan 2009
Location: San Diego, CA
Posts: 3,677
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 839 Post(s)
Liked 1,064 Times
in
747 Posts
So what I did was screw one of the flat Presta nuts all the way down on the stem before inserting it through the hole, then another one on the outside like normal. Is there any issue in doing this, if even temporarily? I think this is a better solution than not putting anything on the inside part of the stem. I run 90 PSI in my tires so I would be afraid the stems would blow out if I didn't have anything holding them back.
#4
Senior Member
Join Date: Oct 2017
Location: NJ
Posts: 627
Bikes: 68 SS, 72 Fuji Finest, 72 PX-10, 77 Pana Pro 7000, 84 Pinnarello Treviso NR, 84 Trek 520, 88 Project KOM, 90 Trek 750, 91 Trek 930
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 184 Post(s)
Liked 204 Times
in
142 Posts
Continental presta tubes have a shoulder on the locknut that sits in a Schrader hole to secure the presta valve.
Likes For dmark:
#5
Senior Member
Join Date: Oct 2013
Location: Mich
Posts: 7,397
Bikes: RSO E-tire dropper fixie brifter
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 6 Post(s)
Liked 2,981 Times
in
1,921 Posts
A short piece of thick heat shrink [marine grade] is what I did for a rim I used in the past. I pre-installed the spare tubes I carried once I found the ideal length needed.
__________________
-Oh Hey!
-Oh Hey!
#6
Senior Member
Join Date: Oct 2014
Location: Portland, OR
Posts: 12,909
Bikes: (2) ti TiCycles, 2007 w/ triple and 2011 fixed, 1979 Peter Mooney, ~1983 Trek 420 now fixed and ~1973 Raleigh Carlton Competition gravel grinder
Mentioned: 129 Post(s)
Tagged: 0 Thread(s)
Quoted: 4806 Post(s)
Liked 3,932 Times
in
2,557 Posts
We used to use thin washers bent to the curvature of the rim. That was before the narrow center channels. Now I'd probably do the same, then grind flats on the sides of the washers so they fit in the channel. (I never did this. I was a sewup only guy.)
#7
Happy With My Bikes
Join Date: Sep 2020
Location: Oklahoma
Posts: 2,187
Bikes: Hi-Ten bike boomers, a Trek Domane and some projects
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 884 Post(s)
Liked 2,308 Times
in
1,118 Posts
The rim on my rear wheel started cracking apart, so I got a new wheel. Unfortunately the new wheel is drilled for Schrader valve stems instead of the Presta stems which I use. I know they make adapters to fit in the holes, but I won't be able to get back to the bike shop for a while. So what I did was screw one of the flat Presta nuts all the way down on the stem before inserting it through the hole, then another one on the outside like normal. Is there any issue in doing this, if even temporarily? I think this is a better solution than not putting anything on the inside part of the stem. I run 90 PSI in my tires so I would be afraid the stems would blow out if I didn't have anything holding them back.
__________________
"It is the unknown around the corner that turns my wheels." -- Heinz Stücke
"It is the unknown around the corner that turns my wheels." -- Heinz Stücke
#8
Senior Member
Join Date: Feb 2012
Location: Golden, CO and Tucson, AZ
Posts: 2,837
Bikes: 2012 Specialized Elite Disc, 1983 Trek 520
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 676 Post(s)
Liked 741 Times
in
430 Posts
Or don't worry about it. My wife's bike has had Presta tubes in Schrader rims for decades without an issue, with high pressure road tires.
#9
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,098
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4211 Post(s)
Liked 3,881 Times
in
2,316 Posts
This, unless one is really bad at attaching and removing the pump valve chuck on and off the valve. Then the added support of the valve stem might reduce a valve base issue which would be caused by the wagging or twisting that some do when dealing with a pump chuck. But once aired up the PV in a SV hole needs no added support during riding. Andy
__________________
AndrewRStewart
AndrewRStewart
#10
Senior Member
Join Date: Jan 2005
Location: Baltimore, MD
Posts: 5,382
Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
Quoted: 2490 Post(s)
Liked 2,958 Times
in
1,681 Posts
You can pick up various diameters of rubber grommets for electrical wiring at almost any hardware store. Chances are you can find a size that fits the rim and valve perfectly.
#11
Mad bike riding scientist
Join Date: Nov 2004
Location: Denver, CO
Posts: 27,369
Bikes: Some silver ones, a red one, a black and orange one, and a few titanium ones
Mentioned: 152 Post(s)
Tagged: 1 Thread(s)
Quoted: 6222 Post(s)
Liked 4,222 Times
in
2,368 Posts
Then have them delivered to your door.
https://www.amazon.com/Quad-Wheels-M...-23&th=1&psc=1
Or rubber grommet style: https://www.amazon.com/Pack-Schrader...%3D%3D&sr=8-21
https://www.amazon.com/Quad-Wheels-M...-23&th=1&psc=1
Or rubber grommet style: https://www.amazon.com/Pack-Schrader...%3D%3D&sr=8-21
Or, even better, shouldered presta nuts. I find them easier to use than any other grommet.
__________________
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
Likes For cyccommute:
#12
Old fart
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,792
Bikes: Several, mostly not name brands.
Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3591 Post(s)
Liked 3,401 Times
in
1,935 Posts
This is what to look for:
Likes For JohnDThompson:
#13
Senior Member
Join Date: Dec 2010
Location: northern Deep South
Posts: 8,904
Bikes: Fuji Touring, Novara Randonee
Mentioned: 36 Post(s)
Tagged: 0 Thread(s)
Quoted: 2604 Post(s)
Liked 1,933 Times
in
1,213 Posts
I've been doing this for years, albeit inadvertently. Wore out a rim, rebuilt the wheel with a new one, and didn't notice the new rim was drilled for Shrader. If I'd noticed, I'd have put on a rubber bushing, or cut a hole in the middle of a 1" square of old inner tube. But it's working fine, so if it ain't broke, why fix it?
#14
Senior Member
Join Date: Oct 2013
Location: Mich
Posts: 7,397
Bikes: RSO E-tire dropper fixie brifter
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 6 Post(s)
Liked 2,981 Times
in
1,921 Posts
drill a new port for the presta valve in the rim somewhere else?
__________________
-Oh Hey!
-Oh Hey!
#15
Full Member
Join Date: May 2008
Location: Tampa
Posts: 311
Bikes: Gunnar Sport 105/UDi2, previous: Lambert, Giant FCR3, Cannondale Synapse Carbon 105, Specialized Roubaix SL4 Comp UDi2
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 29 Post(s)
Likes: 0
Liked 18 Times
in
11 Posts
The Continental presta valve tubes that I bought from Amazon came with shouldered presta nuts.
#16
Palmer
Join Date: Mar 2007
Location: Parts Unknown
Posts: 8,627
Bikes: Mike Melton custom, Alex Moulton AM, Dahon Curl
Mentioned: 37 Post(s)
Tagged: 0 Thread(s)
Quoted: 1671 Post(s)
Liked 1,826 Times
in
1,062 Posts
Some 40 years ago I had some Wolber tubes where the presta valve was held onto the rubber tube by a screwed-down nut, rather than being vulcanized/bonded onto the rubber. They would work for a bit, but eventually all became self-flatting as the rubber stressed around the nut.
#17
It's MY mountain
Join Date: Sep 2006
Location: Mt.Diablo
Posts: 10,002
Bikes: Klein, Merckx, Trek
Mentioned: 70 Post(s)
Tagged: 0 Thread(s)
Quoted: 4338 Post(s)
Liked 2,982 Times
in
1,618 Posts
So what I did was screw one of the flat Presta nuts all the way down on the stem before inserting it through the hole, then another one on the outside like normal. Is there any issue in doing this, if even temporarily? I think this is a better solution than not putting anything on the inside part of the stem. I run 90 PSI in my tires so I would be afraid the stems would blow out if I didn't have anything holding them back.
Second option would be to use a nut or washer. Chances are you don't need it... but depends on rim/tube matchup.
If you don't have a rim-cuts-the-valve problem, the grommet won't solve anything.
I ran this setup for years - no problems except some water inside the rim during the puddle season.
Last edited by DiabloScott; 09-26-22 at 02:00 PM.