Rear Wheel Hub Design Question
#1
Senior Member
Thread Starter
Rear Wheel Hub Design Question
Wouldn't it make sense to have a slightly larger flange on the non-drive side of a rear hub, in order to make the spokes the same length for both sides? Then you could just use spokes of the same length rather than needing two different sets of spokes. Am I missing something, or is it just that it's not a real concern because spoke breakage isn't a very common failure?
I'm looking at the VO touring hub that can be broken down without tools, so you can replace spokes, etc. If companies don't worry about spoke breakage because it isn't a real issue, wouldn't that mean a hub like this isn't really necessary to begin with? Would I be wasting my money for something that isn't really a problem?
I'm looking at the VO touring hub that can be broken down without tools, so you can replace spokes, etc. If companies don't worry about spoke breakage because it isn't a real issue, wouldn't that mean a hub like this isn't really necessary to begin with? Would I be wasting my money for something that isn't really a problem?
Last edited by 3speed; 10-22-17 at 05:18 AM.
#2
Senior Member
Yep! Phil Wood does exactly that on their rear touring hubs. 57.8 mm on non drive side flange, 54.5 on drive side flange. Here are the results for my wheel on a spoke length calculator...
EDIT: Apparently the flange size difference is only on the older Phil Wood hubs. See posts 17 & 18 below.
EDIT: Apparently the flange size difference is only on the older Phil Wood hubs. See posts 17 & 18 below.
Last edited by BobG; 10-26-17 at 03:46 AM.
#3
Senior Member
Join Date: Mar 2008
Posts: 8,688
Mentioned: 46 Post(s)
Tagged: 0 Thread(s)
Quoted: 1074 Post(s)
Liked 295 Times
in
222 Posts
It would make sense from the home mechanic’s perspective.
But its not as beneficial for the wheel building factory. They’re already set up to cope with plenty of different spoke length. Having two sent to the build station is no big deal.
Spoke breakage DOES happen. But not that often. And even if both sides take the same length spokes, you still need to have that length available.
But its not as beneficial for the wheel building factory. They’re already set up to cope with plenty of different spoke length. Having two sent to the build station is no big deal.
Spoke breakage DOES happen. But not that often. And even if both sides take the same length spokes, you still need to have that length available.
#4
Senior Member
Join Date: Feb 2012
Location: Golden, CO and Tucson, AZ
Posts: 2,837
Bikes: 2012 Specialized Elite Disc, 1983 Trek 520
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 676 Post(s)
Liked 741 Times
in
430 Posts
I don't have personal experience with that hub, but the video I just saw looks like you have to remove the cassette before you can service the hub "without tools." So you'll still need a cassette removal tool to change spokes.
#5
Senior Member
I presume you are referring to the VO hub mentioned by the OP. FWIW, my PW rear hub does not need a tool to take the rear cassette off the hub. Nice and handy, but then I have not had any spokes break on that 48 spoke hub while riding - only once in an "accident" when the RD went into the wheel after the black idler wheel came off (screw unscrewed.
#6
Banned
Dish still is required to get the cluster of all those cogs in, and so an IGH, Dishless, still makes a stronger wheel .
that being said I got a lot of tours done with an old Phil 48 spoke rear freewheel hub, had a couple spare spokes in all 3 lengths ,
in my panniers , only ever needed one, , drive side, naturally ..
only needed to bring freewheel remover, borrowed the Big wrench from a local, then we went to the Pub for pints.
...
that being said I got a lot of tours done with an old Phil 48 spoke rear freewheel hub, had a couple spare spokes in all 3 lengths ,
in my panniers , only ever needed one, , drive side, naturally ..
only needed to bring freewheel remover, borrowed the Big wrench from a local, then we went to the Pub for pints.
...
#7
Senior Member
Join Date: Aug 2010
Location: Madison, WI
Posts: 11,212
Bikes: 1961 Ideor, 1966 Perfekt 3 Speed AB Hub, 1994 Bridgestone MB-6, 2006 Airnimal Joey, 2009 Thorn Sherpa, 2013 Thorn Nomad MkII, 2015 VO Pass Hunter, 2017 Lynskey Backroad, 2017 Raleigh Gran Prix, 1980s Bianchi Mixte on a trainer. Others are now gone.
Mentioned: 48 Post(s)
Tagged: 0 Thread(s)
Quoted: 3462 Post(s)
Liked 1,468 Times
in
1,145 Posts
I agree with dabac, a wheel manufacturer that builds up lots of wheels has no incentive to pressure the hub manufacturers to do that. A wheel builder that only makes a small number of wheels is unlikely to get the attention of a company like Shimano.
I used to buy spokes from a local bike shop, they had a good price on the spokes to build one wheel plus they threw in a few spares. But they moved out of town, other local bike shops want a fortune for enough spokes for a wheel. So now I buy in bulk on line when I build up a wheel. I use Wheelsmith spokes, that means buying a bag of 50 for each length.
I used Sapim nipples for my last two pairs of wheels. On the most recent rear wheel that I built, I used these nipple washers on the drive side. They add about 0.7mm to the length of the spoke that you need.
Round PolyAx (HM) Washers (20 pieces)
By using those nipple washers on the drive side, I could use the same spoke length on both sides. I am not saying that they will always save you from needing two lengths, but in my case they did.
I used to buy spokes from a local bike shop, they had a good price on the spokes to build one wheel plus they threw in a few spares. But they moved out of town, other local bike shops want a fortune for enough spokes for a wheel. So now I buy in bulk on line when I build up a wheel. I use Wheelsmith spokes, that means buying a bag of 50 for each length.
I used Sapim nipples for my last two pairs of wheels. On the most recent rear wheel that I built, I used these nipple washers on the drive side. They add about 0.7mm to the length of the spoke that you need.
Round PolyAx (HM) Washers (20 pieces)
By using those nipple washers on the drive side, I could use the same spoke length on both sides. I am not saying that they will always save you from needing two lengths, but in my case they did.
Last edited by Tourist in MSN; 10-22-17 at 04:19 PM.
#8
-
It would be nice if only one length spoke was required for a bike but it's not that big a deal to carry spares in 2 or 3 lengths. More important would be to design rear hub spacing/diameter to minimize dish, to increase wheel longevity for loaded touring use. AFAIK the only cassette hub that offers zero dish is the 145mm DT Swiss 540, used by CoMotion for touring singles, which is a $310 hub on sale. Phil Wood used to make the FSA hub with very little dish (in the 7s freewheel version), a custom version sold by Rivendell, which has been discontinued.
The only advantage of the VO GC hub over a Shimano XT is it's replaceable sealed bearings with no possibility of bearing cup wear, so potentially a longevity advantage - but also consider that the VO hub costs as much as 3-4 XT hubs.
AFAIK the only truly dishless IGH is Rohloff Speedhub (29mm flange spacing/100mm PCD both L&R). IGHs generally do reduce dish over cassette hubs but the only one that has symmetric flange spacing and diameter is Speedhub.
You can build with asymmetrically-drilled rims to reduce dish, Velocity sells a couple models (A23 and Synergy, discontinued).
The only advantage of the VO GC hub over a Shimano XT is it's replaceable sealed bearings with no possibility of bearing cup wear, so potentially a longevity advantage - but also consider that the VO hub costs as much as 3-4 XT hubs.
You can build with asymmetrically-drilled rims to reduce dish, Velocity sells a couple models (A23 and Synergy, discontinued).
Last edited by seeker333; 10-22-17 at 03:03 PM.
#9
Senior Member
Join Date: Apr 2009
Location: New Rochelle, NY
Posts: 38,725
Bikes: too many bikes from 1967 10s (5x2)Frejus to a Sumitomo Ti/Chorus aluminum 10s (10x2), plus one non-susp mtn bike I use as my commuter
Mentioned: 140 Post(s)
Tagged: 1 Thread(s)
Quoted: 5793 Post(s)
Liked 2,585 Times
in
1,433 Posts
To start with the effect of flange size varies either the number of spokes and crosses. It's greatest with a radial pattern where all the spokes go to the edge of the flange. It's least, approaching zero, on a full tangent build, ie. 36h x4 where all the spokes come down to the line of the axle. Everything else is in between, but what matters is that actual line the spokes take.
That said, the main goal isn't about spoke length, but bracing angle which determines the tension right and left. In that vein, you'd want to make the right flange bigger, to increase that bracing on that side. Making the left would be counterproductive, make things worse, or at best, having little effect.
That said, the main goal isn't about spoke length, but bracing angle which determines the tension right and left. In that vein, you'd want to make the right flange bigger, to increase that bracing on that side. Making the left would be counterproductive, make things worse, or at best, having little effect.
__________________
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
#10
Senior Member
Thread Starter
No, you can remove the freehub with cassette attached without tools. The point of the hub is largely that you can replace spokes in a pinch without having to use a cassette tool.
#11
Senior Member
Join Date: Mar 2008
Posts: 8,688
Mentioned: 46 Post(s)
Tagged: 0 Thread(s)
Quoted: 1074 Post(s)
Liked 295 Times
in
222 Posts
That said, the main goal isn't about spoke length, but bracing angle which determines the tension right and left. In that vein, you'd want to make the right flange bigger, to increase that bracing on that side. Making the left would be counterproductive, make things worse, or at best, having little effect.
Moving the flange a few mm inwards would retain the spoke path and lateral bracing angle with few to none consequences.
#12
Senior Member
Join Date: Apr 2009
Location: New Rochelle, NY
Posts: 38,725
Bikes: too many bikes from 1967 10s (5x2)Frejus to a Sumitomo Ti/Chorus aluminum 10s (10x2), plus one non-susp mtn bike I use as my commuter
Mentioned: 140 Post(s)
Tagged: 1 Thread(s)
Quoted: 5793 Post(s)
Liked 2,585 Times
in
1,433 Posts
Still, if someone wanted to make a hubset that use all identical spoke lengths, it’d be easy enough to compensate the geometry for the larger diameter NDS flange.
Moving the flange a few mm inwards would retain the spoke path and lateral bracing angle with few to none consequences.
Moving the flange a few mm inwards would retain the spoke path and lateral bracing angle with few to none consequences.
It same length spokes are desired for some reason, it might be possible by reducing the number of crosses on the right, or on both flanges, then tweaking the flange size.
In any case, the goal of a lower tension different right and left should trump all others. That's done by increasing the right side bracing angle, a goal achieved with a larger right flange combined with reduced cross, ie. The larger flange also mitigates the torsional effects of reduced cross since the spokes pine of action is moved out.
__________________
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
#13
Banned
[QUOTE=seeker333;19945465. You can build with asymmetrically-drilled rims to reduce dish [/QUOTE]
Though, if rim is narrow all you have is at most is half its width in shifting the holes,
drilling an asymmetric rim extrusion...
(Like drilling a 45mm wide rim, Fairbanks AK, Snow Cats, off center, or the even wider 4" fat bike rims )
Though, if rim is narrow all you have is at most is half its width in shifting the holes,
drilling an asymmetric rim extrusion...
(Like drilling a 45mm wide rim, Fairbanks AK, Snow Cats, off center, or the even wider 4" fat bike rims )
#14
Senior Member
Join Date: Aug 2010
Location: Madison, WI
Posts: 11,212
Bikes: 1961 Ideor, 1966 Perfekt 3 Speed AB Hub, 1994 Bridgestone MB-6, 2006 Airnimal Joey, 2009 Thorn Sherpa, 2013 Thorn Nomad MkII, 2015 VO Pass Hunter, 2017 Lynskey Backroad, 2017 Raleigh Gran Prix, 1980s Bianchi Mixte on a trainer. Others are now gone.
Mentioned: 48 Post(s)
Tagged: 0 Thread(s)
Quoted: 3462 Post(s)
Liked 1,468 Times
in
1,145 Posts
One thing I find a bit frustrating is front hubs, not rear. I built up a new dynohub wheel last spring, planned to use it on a bike with rim brakes but I thought that some day I might want to be able to use that wheel with a disc so I considered using a disc type hub. I understand why SP used a larger diameter flange on the disc side, but why could they not use the same flange diameter also on the other side? It is an undished wheel, but I still would have had to buy two bags of spokes for that wheel because they used different flange diameters.
https://www.sp-dynamo.com/8-series-pic/PD-8-QR-01.pdf
Since it was for a rim brake wheel, I bought the non-disc version of the hub to avoid the extra cost for spokes.
https://www.sp-dynamo.com/8-series-pic/PD-8-QR-01.pdf
Since it was for a rim brake wheel, I bought the non-disc version of the hub to avoid the extra cost for spokes.
#15
Mad bike riding scientist
Join Date: Nov 2004
Location: Denver, CO
Posts: 27,368
Bikes: Some silver ones, a red one, a black and orange one, and a few titanium ones
Mentioned: 152 Post(s)
Tagged: 1 Thread(s)
Quoted: 6220 Post(s)
Liked 4,221 Times
in
2,367 Posts
I'm not sure where you are getting your dimensions. For the ones listed on their website, they are both 59mm. All the ones I've worked with...3 sets...have the same dimensions on both flanges.
__________________
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
#16
Senior Member
Cycco, I'm using the hub dimensions chart at the PW website. Spoke hole diameters (called hub flange diameter at calculator above) of 57.8 and 54.5 on an 8 speed freewheel hub. All things being equal there should be a 3.3 mm difference in flange diameter.
Last edited by BobG; 10-23-17 at 05:48 PM.
#17
Mad bike riding scientist
Join Date: Nov 2004
Location: Denver, CO
Posts: 27,368
Bikes: Some silver ones, a red one, a black and orange one, and a few titanium ones
Mentioned: 152 Post(s)
Tagged: 1 Thread(s)
Quoted: 6220 Post(s)
Liked 4,221 Times
in
2,367 Posts
You are working off some very old information. All of their cassette hubs have the same flange diameter and have for more than 10 years. My 2005 FSC hubs have the same flange diameter.
__________________
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
#18
Senior Member
I don't know what to say Stuart. My hub is at least 25 years old but if you click on "Phil Wood hub dimensions" at the home page of the current website it will show the same dimensions that I posted for an 8 speed freewheel touring hub. The same numbers are listed for the cassette versions.
Phil Wood & Co.
https://www.philwood.com/philpdfs/whe...ding_break.pdf
Spoke length came out perfect entering those figure into the calculator. I don't have a caliper to measure the flanges on the built up wheel but eyeballing with a tape measure the left flange appears to be a few millimeters larger.
edit: I see the problem now. Phil Wood is posting old numbers at the pdf file. When you click on the various hubs on the home page your numbers come up. They should delete the pdf link from their homepage! That said, my old hub has the two flange sizes. You are correct, they have been changed!
Phil Wood & Co.
https://www.philwood.com/philpdfs/whe...ding_break.pdf
Spoke length came out perfect entering those figure into the calculator. I don't have a caliper to measure the flanges on the built up wheel but eyeballing with a tape measure the left flange appears to be a few millimeters larger.
edit: I see the problem now. Phil Wood is posting old numbers at the pdf file. When you click on the various hubs on the home page your numbers come up. They should delete the pdf link from their homepage! That said, my old hub has the two flange sizes. You are correct, they have been changed!
Last edited by BobG; 10-24-17 at 01:35 PM.
#19
Senior Member
Join Date: Feb 2009
Posts: 2,522
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 1422 Post(s)
Likes: 0
Liked 7 Times
in
5 Posts
If you get a few extra bodies, it makes swapping cassettes really easy.
My PowerTaps are like that and they are based on DT hubs which also just pull off.
#20
Mad bike riding scientist
Join Date: Nov 2004
Location: Denver, CO
Posts: 27,368
Bikes: Some silver ones, a red one, a black and orange one, and a few titanium ones
Mentioned: 152 Post(s)
Tagged: 1 Thread(s)
Quoted: 6220 Post(s)
Liked 4,221 Times
in
2,367 Posts
edit: I see the problem now. Phil Wood is posting old numbers at the pdf file. When you click on the various hubs on the home page your numbers come up. They should delete the pdf link from their homepage! That said, my old hub has the two flange sizes. You are correct, they have been changed!
As for the flange sizes, that's what bothered me about the PDF originally. All of the Phils I have are the same size on both flanges.
__________________
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
#21
Senior Member
Join Date: Sep 2008
Posts: 5,201
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 137 Post(s)
Likes: 0
Liked 81 Times
in
64 Posts
Wouldn't it make sense to have a slightly larger flange on the non-drive side of a rear hub, in order to make the spokes the same length for both sides? Then you could just use spokes of the same length rather than needing two different sets of spokes. Am I missing something, or is it just that it's not a real concern because spoke breakage isn't a very common failure?
I'm looking at the VO touring hub that can be broken down without tools, so you can replace spokes, etc. If companies don't worry about spoke breakage because it isn't a real issue, wouldn't that mean a hub like this isn't really necessary to begin with? Would I be wasting my money for something that isn't really a problem?
I'm looking at the VO touring hub that can be broken down without tools, so you can replace spokes, etc. If companies don't worry about spoke breakage because it isn't a real issue, wouldn't that mean a hub like this isn't really necessary to begin with? Would I be wasting my money for something that isn't really a problem?
#22
Banned
One thing I find a bit frustrating is front hubs, not rear. I built up a new dynohub wheel last spring, planned to use it on a bike with rim brakes but I thought that some day I might want to be able to use that wheel with a disc so I considered using a disc type hub. I understand why SP used a larger diameter flange on the disc side, but why could they not use the same flange diameter also on the other side? It is an undished wheel, but I still would have had to buy two bags of spokes for that wheel because they used different flange diameters.
https://www.sp-dynamo.com/8-series-pic/PD-8-QR-01.pdf
Since it was for a rim brake wheel, I bought the non-disc version of the hub to avoid the extra cost for spokes.
https://www.sp-dynamo.com/8-series-pic/PD-8-QR-01.pdf
Since it was for a rim brake wheel, I bought the non-disc version of the hub to avoid the extra cost for spokes.
IDK SP, but Schmidt ,
has a little dish on the front disc 6 bolt *, to make clearance for the disc, but did not use 2 different lengths, per side.
*they call these the 'classic' now .. a black, 32 hole, the left flange is closer to the hub shell center band..
.....
#23
Slow Rider
I use Shimano Deore hubs for my bikes and find, with 559 (26") rims, the lengths on both sides are nearly the same for both front and rear hubs. Lengths vary from about 263mm to 266mm, so I just use, and carry, 265mm spokes.