Had a weird chain/chainring issue
#1
Full Member
Thread Starter
Had a weird chain/chainring issue
I have a 'new to me' 2021 Norco Bigfoot 2. When I got it I gave it a quick once over and everything seemed in perfect order, very minimal wear, and didn't even need to tweak the indexing... worked perfect. We finally got some snow and I took it for 2 leasurely 10km rides this last weekend, again all worked perfect. Getting back to the parking lot at the end of the second ride the chain dropped off the chainring. No reason for it to, it was flat and smooth. I put the chain back on (yes I'm aware of needing to line up the narrow/wide) and it dropped off in half a revolution of the crank. Tried again, I had to give the chain a good press to fully seat all around the chainring, but it immediately rode right off the chainring. Tried a third time and same thing.
Thankfully we were back at the parking lot so I walked the bike back to the truck. It was driving me nuts trying to figure out why it would be doing that. When I got the bike home and on the work stand it was doing the same thing. It was like the chainring is designed for the typical 0.500" pitch but the chain was 0.490". To try to observe better what was going on I used my fingers to guide the chain to keep it riding on the chain ring. It was riding on top of the teeth, not really meshing as before. After about 3 revolutions of the crank the chain just fell onto the chain ring and worked as it should. Now I can't make it work anyway but properly. Good that it works, Bad that I now have trust issues.
WTF happened? Anyone seen this before?
Thankfully we were back at the parking lot so I walked the bike back to the truck. It was driving me nuts trying to figure out why it would be doing that. When I got the bike home and on the work stand it was doing the same thing. It was like the chainring is designed for the typical 0.500" pitch but the chain was 0.490". To try to observe better what was going on I used my fingers to guide the chain to keep it riding on the chain ring. It was riding on top of the teeth, not really meshing as before. After about 3 revolutions of the crank the chain just fell onto the chain ring and worked as it should. Now I can't make it work anyway but properly. Good that it works, Bad that I now have trust issues.
WTF happened? Anyone seen this before?
Likes For Camilo:
#3
Full Member
Thread Starter
Likes For Ryan_M:
#4
Senior Member
Join Date: May 2008
Location: Fredericksburg, Va
Posts: 9,579
Bikes: '65 Frejus TDF, '73 Bottecchia Giro d'Italia, '83 Colnago Superissimo, '84 Trek 610, '84 Trek 760, '88 Pinarello Veneto, '88 De Rosa Pro, '89 Pinarello Montello, '94 Burley Duet, 97 Specialized RockHopper, 2010 Langster, Tern Link D8
Mentioned: 73 Post(s)
Tagged: 0 Thread(s)
Quoted: 1609 Post(s)
Liked 2,216 Times
in
1,103 Posts
Check chain "stretch."
how clean/dirty is the chain and associated parts?
how clean/dirty is the chain and associated parts?
__________________
Bikes don't stand alone. They are two tired.
Bikes don't stand alone. They are two tired.
#5
Senior Member
Join Date: Apr 2009
Location: New Rochelle, NY
Posts: 38,726
Bikes: too many bikes from 1967 10s (5x2)Frejus to a Sumitomo Ti/Chorus aluminum 10s (10x2), plus one non-susp mtn bike I use as my commuter
Mentioned: 140 Post(s)
Tagged: 1 Thread(s)
Quoted: 5793 Post(s)
Liked 2,592 Times
in
1,436 Posts
Not clear. Is the chain falling off when riding, or only.when you're off the bike?
If the latter, consider that a certain amount of upper loop tension keeps the chain tugged down on sprockets. Absent that a chain, possibly stiffened by cold lube can start riding high leading, to it falling off.
If the latter, consider that a certain amount of upper loop tension keeps the chain tugged down on sprockets. Absent that a chain, possibly stiffened by cold lube can start riding high leading, to it falling off.
Likes For FBinNY:
#6
aged to perfection
Join Date: Jun 2009
Location: PacNW
Posts: 1,820
Bikes: Dinucci Allez 2.0, Richard Sachs, Alex Singer, Serotta, Masi GC, Raleigh Pro Mk.1, Hetchins, etc
Mentioned: 24 Post(s)
Tagged: 0 Thread(s)
Quoted: 840 Post(s)
Liked 1,262 Times
in
667 Posts
you may have a bent tooth on the chainring
/markp
/markp
#7
Senior Member
Join Date: Oct 2013
Location: Mich
Posts: 7,397
Bikes: RSO E-tire dropper fixie brifter
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 6 Post(s)
Liked 2,981 Times
in
1,921 Posts
is the rear axle pivoting around. Check that the wheel stays consistent within the stays, both side to side & front to back.
__________________
-Oh Hey!
-Oh Hey!
#8
Just Pedaling
Join Date: Oct 2021
Location: US West Coast
Posts: 1,016
Bikes: YEP!
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 335 Post(s)
Liked 523 Times
in
349 Posts
I'd start by measuring the chain for wear and then making sure the upper and lower stops are set on the frnt DR. If that all checks out take a really close look at the chainring. Does it jump both or just the large? There's a reason it's not always working properly. Your mission, if you decide to tackle it, is to find out why. Good luck, Nice bike BTW
#9
Senior Member
Join Date: Apr 2019
Location: UK
Posts: 1,404
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 682 Post(s)
Liked 453 Times
in
338 Posts
I'd start by measuring the chain for wear and then making sure the upper and lower stops are set on the frnt DR. If that all checks out take a really close look at the chainring. Does it jump both or just the large? There's a reason it's not always working properly. Your mission, if you decide to tackle it, is to find out why. Good luck, Nice bike BTW
if it was still playing up I was also thinking chain stretch or maybe worn chainring and new chain where the chain was rising up the teeth (or misplaced N-W but he covered that) but the fact it fixed itself is just very odd.
edit: and the other thought I had was maybe an untightened quick link but this was after a ride where it was fine so can’t be
Last edited by choddo; 02-22-24 at 01:46 AM.
Likes For choddo:
#10
Senior Member
Join Date: Oct 2014
Location: Portland, OR
Posts: 12,909
Bikes: (2) ti TiCycles, 2007 w/ triple and 2011 fixed, 1979 Peter Mooney, ~1983 Trek 420 now fixed and ~1973 Raleigh Carlton Competition gravel grinder
Mentioned: 129 Post(s)
Tagged: 0 Thread(s)
Quoted: 4806 Post(s)
Liked 3,932 Times
in
2,557 Posts
New chain on an older chainring? This could cause your 0.490 chain on 0.500" teeth effect only now it's 0.500 chain on 0.510 teeth. Or a bent tooth as mentioned above. Or narrow-wide issues? Perhaps that narrow-wide chainring and that brand/model of chain? (I"ve never done them so that's a pure guess.)
#11
Senior Member
Join Date: Apr 2009
Location: New Rochelle, NY
Posts: 38,726
Bikes: too many bikes from 1967 10s (5x2)Frejus to a Sumitomo Ti/Chorus aluminum 10s (10x2), plus one non-susp mtn bike I use as my commuter
Mentioned: 140 Post(s)
Tagged: 1 Thread(s)
Quoted: 5793 Post(s)
Liked 2,592 Times
in
1,436 Posts
Based on how manually pressing it around the ring solved the problem, I wonder if it might have been partly frozen or at least stiffened by the cold.
__________________
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
Likes For Mtracer:
#13
Just Pedaling
Join Date: Oct 2021
Location: US West Coast
Posts: 1,016
Bikes: YEP!
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 335 Post(s)
Liked 523 Times
in
349 Posts
No front mech, it’s a 1X
if it was still playing up I was also thinking chain stretch or maybe worn chainring and new chain where the chain was rising up the teeth (or misplaced N-W but he covered that) but the fact it fixed itself is just very odd.
edit: and the other thought I had was maybe an untightened quick link but this was after a ride where it was fine so can’t be
if it was still playing up I was also thinking chain stretch or maybe worn chainring and new chain where the chain was rising up the teeth (or misplaced N-W but he covered that) but the fact it fixed itself is just very odd.
edit: and the other thought I had was maybe an untightened quick link but this was after a ride where it was fine so can’t be
Likes For SpedFast:
#14
Senior Member
Join Date: Jul 2005
Location: Boulder County, CO
Posts: 4,398
Bikes: '80 Masi Gran Criterium, '12 Trek Madone, early '60s Frejus track
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 514 Post(s)
Liked 451 Times
in
339 Posts
Suspend the bike (workstand, skyhook, whatever) and watch the chain mesh with the chainring as you turn the crank slowly. The problem should become apparent to the naked eye.
Likes For oldbobcat:
#15
Full Member
Thread Starter
I really hate that I can't find anything wrong. It's going to take some time for me to stop worrying about that every time I go out..