Campy Record ti 9 speed Ergo shifter
#1
Senior Member
Thread Starter
Join Date: Nov 2013
Location: Southern California
Posts: 1,470
Mentioned: 14 Post(s)
Tagged: 0 Thread(s)
Quoted: 802 Post(s)
Liked 759 Times
in
413 Posts
Campy Record ti 9 speed Ergo shifter
I've never owned Campy, so before I take them apart potentially needlessly for service....are the downshifts for these older style brifters especially 'hard'? The upshifts are much easier to push.
#2
Senior Member
I may be biased because 9 speed Ergos are my favorite type of brifter, but no the downshifts are not particularly "hard". I find them to precise and easy to shift, while being comfortable in the hand.
__________________
Check out www.djcatnap.com for articles on vintage Japanese & French bicycle restorations, components and history.
Check out www.djcatnap.com for articles on vintage Japanese & French bicycle restorations, components and history.
#3
Senior Member
Thread Starter
Join Date: Nov 2013
Location: Southern California
Posts: 1,470
Mentioned: 14 Post(s)
Tagged: 0 Thread(s)
Quoted: 802 Post(s)
Liked 759 Times
in
413 Posts
Though, thinking more now, I guess that's to be expected because the thumb shifts will be aided by the cable tension...perhaps once setup on the bike this will make sense.
#4
Ride, Wrench, Swap, Race
Join Date: Jan 2010
Location: Northern California
Posts: 9,197
Bikes: Cheltenham-Pedersen racer, Boulder F/S Paris-Roubaix, Varsity racer, '52 Christophe, '62 Continental, '92 Merckx, '75 Limongi, '76 Presto, '72 Gitane SC, '71 Schwinn SS, etc.
Mentioned: 132 Post(s)
Tagged: 0 Thread(s)
Quoted: 1566 Post(s)
Liked 1,300 Times
in
867 Posts
It's definitely precise, nothing mushy about it, just I'm surprised by how much more effort is required to push the thumb.
Though, thinking more now, I guess that's to be expected because the thumb shifts will be aided by the cable tension...perhaps once setup on the bike this will make sense.
Though, thinking more now, I guess that's to be expected because the thumb shifts will be aided by the cable tension...perhaps once setup on the bike this will make sense.
If there was a way to add lube with a needle-point applicator to the indexing ring and indexing springs I would put a squirt of motorcycle chain lube in, but only if this could be done without making a mess or with lube getting under the rubber hood which would be a disaster.
#5
Senior Member
Join Date: Aug 2007
Location: Evanston, IL
Posts: 5,126
Bikes: many
Mentioned: 63 Post(s)
Tagged: 0 Thread(s)
Quoted: 1455 Post(s)
Liked 1,404 Times
in
768 Posts
Yes, the shifting force will be dramatically reduced!
If there was a way to add lube with a needle-point applicator to the indexing ring and indexing springs I would put a squirt of motorcycle chain lube in, but only if this could be done without making a mess or with lube getting under the rubber hood which would be a disaster.
If there was a way to add lube with a needle-point applicator to the indexing ring and indexing springs I would put a squirt of motorcycle chain lube in, but only if this could be done without making a mess or with lube getting under the rubber hood which would be a disaster.
#6
Senior Member
Join Date: Jan 2008
Location: Beaverton, OR
Posts: 14,752
Bikes: Yes
Mentioned: 525 Post(s)
Tagged: 0 Thread(s)
Quoted: 3236 Post(s)
Liked 3,883 Times
in
1,443 Posts
Yes, the Campy Ergo design attempts to balance the forces so that both upshifts and downshifts feel the same on the road. When they're not installed, it acts very weird, often skipping over gears in one direction, because the forces are out of balance without the derailleur pulling on the cable.
__________________
My Bikes
My Bikes
#7
Senior Member
Join Date: Aug 2015
Location: Kingdom of Hawai'i
Posts: 1,211
Bikes: Peugeot, Legnano, Fuji, Zunow, De Rosa, Miyata, Bianchi, Pinarello, Specialized, Bridgestone, Cinelli, Merckx
Mentioned: 17 Post(s)
Tagged: 0 Thread(s)
Quoted: 433 Post(s)
Liked 517 Times
in
223 Posts
Likes For billytwosheds: