Two likely stupid questions...
#1
Edumacator
Thread Starter
Join Date: Jan 2018
Location: Goose Creek, SC
Posts: 6,812
Bikes: '87 Crestdale, '87 Basso Gap, '92 Rossin Performance EL-OS, 1990 VanTuyl, 1980s Losa, 1985 Trek 670, 1982 AD SLE, 1987 PX10, etc...
Mentioned: 59 Post(s)
Tagged: 0 Thread(s)
Quoted: 2440 Post(s)
Liked 3,130 Times
in
1,969 Posts
Two likely stupid questions...
One, on Neco and some Shimano hubs, they have this annoying band on the drive side. I assume it is to hold the bearing cartridge or something. But not much space for the crank tapers.
And two, how do you get the axle unit back into the SPD-SL pedals? Or take them out?
And two, how do you get the axle unit back into the SPD-SL pedals? Or take them out?
__________________
1987 Crest Cannondale, 1987 Basso Gap, 1992 Rossin Performance EL, 1990ish Van Tuyl, 1985 Trek 670, 1982 AD SLE, 2003 Pinarello Surprise, 1990ish MBK Atlantique, 1987 Peugeot Competition, 1987 Nishiki Tri-A, 1981 Faggin, 1996 Cannondale M500, 1984 Mercian, 1982 AD SuperLeicht, 1985 Massi (model unknown), 1988 Daccordi Griffe , 1989 Fauxsin MTB, 1981 Ciocc Mockba, 1992 Bianchi Giro, 1977 Colnago Super
1987 Crest Cannondale, 1987 Basso Gap, 1992 Rossin Performance EL, 1990ish Van Tuyl, 1985 Trek 670, 1982 AD SLE, 2003 Pinarello Surprise, 1990ish MBK Atlantique, 1987 Peugeot Competition, 1987 Nishiki Tri-A, 1981 Faggin, 1996 Cannondale M500, 1984 Mercian, 1982 AD SuperLeicht, 1985 Massi (model unknown), 1988 Daccordi Griffe , 1989 Fauxsin MTB, 1981 Ciocc Mockba, 1992 Bianchi Giro, 1977 Colnago Super
#2
Bianchi Goddess
Join Date: Apr 2009
Location: Shady Pines Retirement Fort Wayne, In
Posts: 27,860
Bikes: Too many to list here check my signature.
Mentioned: 192 Post(s)
Tagged: 2 Thread(s)
Quoted: 2930 Post(s)
Liked 2,928 Times
in
1,493 Posts
I think you need one of these. But it's been so long I don't remember if there a set of flats between this nut and the body or you just hold the body
__________________
“One morning you wake up, the girl is gone, the bikes are gone, all that's left behind is a pair of old tires and a tube of tubular glue, all squeezed out"
Sugar "Kane" Kowalczyk
“One morning you wake up, the girl is gone, the bikes are gone, all that's left behind is a pair of old tires and a tube of tubular glue, all squeezed out"
Sugar "Kane" Kowalczyk
#3
Senior Member
Join Date: Feb 2008
Location: Peoria, IL
Posts: 4,476
Mentioned: 86 Post(s)
Tagged: 0 Thread(s)
Quoted: 1829 Post(s)
Liked 3,376 Times
in
1,580 Posts
There's a fairly cheap tool for SPD pedals of that sort, the TL-PD40.
I got mine from the local shop for a few bucks. Works nicely with a bench vise.
also.. it took me a bit to learn that "overhauling" such a SPD pedal is usually done by pulling the axle assembly, injecting some new grease into the bottom of the body, and reinstalling the axle assembly. The old grease will ooze out around the seal during the axle re-installation.
Steve in Peoria
I got mine from the local shop for a few bucks. Works nicely with a bench vise.
also.. it took me a bit to learn that "overhauling" such a SPD pedal is usually done by pulling the axle assembly, injecting some new grease into the bottom of the body, and reinstalling the axle assembly. The old grease will ooze out around the seal during the axle re-installation.
Steve in Peoria
Likes For steelbikeguy:
#4
Edumacator
Thread Starter
Join Date: Jan 2018
Location: Goose Creek, SC
Posts: 6,812
Bikes: '87 Crestdale, '87 Basso Gap, '92 Rossin Performance EL-OS, 1990 VanTuyl, 1980s Losa, 1985 Trek 670, 1982 AD SLE, 1987 PX10, etc...
Mentioned: 59 Post(s)
Tagged: 0 Thread(s)
Quoted: 2440 Post(s)
Liked 3,130 Times
in
1,969 Posts
There's a fairly cheap tool for SPD pedals of that sort, the TL-PD40.
I got mine from the local shop for a few bucks. Works nicely with a bench vise.
also.. it took me a bit to learn that "overhauling" such a SPD pedal is usually done by pulling the axle assembly, injecting some new grease into the bottom of the body, and reinstalling the axle assembly. The old grease will ooze out around the seal during the axle re-installation.
Steve in Peoria
I got mine from the local shop for a few bucks. Works nicely with a bench vise.
also.. it took me a bit to learn that "overhauling" such a SPD pedal is usually done by pulling the axle assembly, injecting some new grease into the bottom of the body, and reinstalling the axle assembly. The old grease will ooze out around the seal during the axle re-installation.
Steve in Peoria
__________________
1987 Crest Cannondale, 1987 Basso Gap, 1992 Rossin Performance EL, 1990ish Van Tuyl, 1985 Trek 670, 1982 AD SLE, 2003 Pinarello Surprise, 1990ish MBK Atlantique, 1987 Peugeot Competition, 1987 Nishiki Tri-A, 1981 Faggin, 1996 Cannondale M500, 1984 Mercian, 1982 AD SuperLeicht, 1985 Massi (model unknown), 1988 Daccordi Griffe , 1989 Fauxsin MTB, 1981 Ciocc Mockba, 1992 Bianchi Giro, 1977 Colnago Super
1987 Crest Cannondale, 1987 Basso Gap, 1992 Rossin Performance EL, 1990ish Van Tuyl, 1985 Trek 670, 1982 AD SLE, 2003 Pinarello Surprise, 1990ish MBK Atlantique, 1987 Peugeot Competition, 1987 Nishiki Tri-A, 1981 Faggin, 1996 Cannondale M500, 1984 Mercian, 1982 AD SuperLeicht, 1985 Massi (model unknown), 1988 Daccordi Griffe , 1989 Fauxsin MTB, 1981 Ciocc Mockba, 1992 Bianchi Giro, 1977 Colnago Super
#5
Senior Member
Join Date: Feb 2008
Location: Peoria, IL
Posts: 4,476
Mentioned: 86 Post(s)
Tagged: 0 Thread(s)
Quoted: 1829 Post(s)
Liked 3,376 Times
in
1,580 Posts
No idea whether there is a metal version. I imagine that @Bianchigirll's TL-PD30 is the shop version.
It did occur to me that a properly sized socket might do the job too... until I counted the splines and realized that there were 10. I'm pretty sure that I don't have a set of 10 point sockets.
Steve in Peoria
Likes For steelbikeguy:
#6
Bianchi Goddess
Join Date: Apr 2009
Location: Shady Pines Retirement Fort Wayne, In
Posts: 27,860
Bikes: Too many to list here check my signature.
Mentioned: 192 Post(s)
Tagged: 2 Thread(s)
Quoted: 2930 Post(s)
Liked 2,928 Times
in
1,493 Posts
steelbikeguy OH I forgot about that one.
__________________
“One morning you wake up, the girl is gone, the bikes are gone, all that's left behind is a pair of old tires and a tube of tubular glue, all squeezed out"
Sugar "Kane" Kowalczyk
“One morning you wake up, the girl is gone, the bikes are gone, all that's left behind is a pair of old tires and a tube of tubular glue, all squeezed out"
Sugar "Kane" Kowalczyk
#7
Edumacator
Thread Starter
Join Date: Jan 2018
Location: Goose Creek, SC
Posts: 6,812
Bikes: '87 Crestdale, '87 Basso Gap, '92 Rossin Performance EL-OS, 1990 VanTuyl, 1980s Losa, 1985 Trek 670, 1982 AD SLE, 1987 PX10, etc...
Mentioned: 59 Post(s)
Tagged: 0 Thread(s)
Quoted: 2440 Post(s)
Liked 3,130 Times
in
1,969 Posts
steelbikeguy OH I forgot about that one.
Im not sure why Shimano changed that collar fitting for the Dura Ace one to the current one.
__________________
1987 Crest Cannondale, 1987 Basso Gap, 1992 Rossin Performance EL, 1990ish Van Tuyl, 1985 Trek 670, 1982 AD SLE, 2003 Pinarello Surprise, 1990ish MBK Atlantique, 1987 Peugeot Competition, 1987 Nishiki Tri-A, 1981 Faggin, 1996 Cannondale M500, 1984 Mercian, 1982 AD SuperLeicht, 1985 Massi (model unknown), 1988 Daccordi Griffe , 1989 Fauxsin MTB, 1981 Ciocc Mockba, 1992 Bianchi Giro, 1977 Colnago Super
1987 Crest Cannondale, 1987 Basso Gap, 1992 Rossin Performance EL, 1990ish Van Tuyl, 1985 Trek 670, 1982 AD SLE, 2003 Pinarello Surprise, 1990ish MBK Atlantique, 1987 Peugeot Competition, 1987 Nishiki Tri-A, 1981 Faggin, 1996 Cannondale M500, 1984 Mercian, 1982 AD SuperLeicht, 1985 Massi (model unknown), 1988 Daccordi Griffe , 1989 Fauxsin MTB, 1981 Ciocc Mockba, 1992 Bianchi Giro, 1977 Colnago Super
#8
Senior Member
Join Date: Feb 2008
Location: Peoria, IL
Posts: 4,476
Mentioned: 86 Post(s)
Tagged: 0 Thread(s)
Quoted: 1829 Post(s)
Liked 3,376 Times
in
1,580 Posts
Why does Shimano do this sort of nonsense??
Steve in Peoria
Likes For oneclick:
#10
Senior Member
Join Date: Apr 2011
Posts: 7,067
Mentioned: 41 Post(s)
Tagged: 0 Thread(s)
Quoted: 4409 Post(s)
Liked 1,566 Times
in
1,028 Posts
Where are the threads on the right pedal assembly?
That BB with the collar is for a particular crank.
That BB with the collar is for a particular crank.
#11
Edumacator
Thread Starter
Join Date: Jan 2018
Location: Goose Creek, SC
Posts: 6,812
Bikes: '87 Crestdale, '87 Basso Gap, '92 Rossin Performance EL-OS, 1990 VanTuyl, 1980s Losa, 1985 Trek 670, 1982 AD SLE, 1987 PX10, etc...
Mentioned: 59 Post(s)
Tagged: 0 Thread(s)
Quoted: 2440 Post(s)
Liked 3,130 Times
in
1,969 Posts
I assume 9/16? Haven't tried it yet in a crankset, but I don't think it is a 1/2 inch (I assume that was what you were asking?)
Poop. Must be a thin one of sorts. I was hoping to use it for a build for sale.
Poop. Must be a thin one of sorts. I was hoping to use it for a build for sale.
__________________
1987 Crest Cannondale, 1987 Basso Gap, 1992 Rossin Performance EL, 1990ish Van Tuyl, 1985 Trek 670, 1982 AD SLE, 2003 Pinarello Surprise, 1990ish MBK Atlantique, 1987 Peugeot Competition, 1987 Nishiki Tri-A, 1981 Faggin, 1996 Cannondale M500, 1984 Mercian, 1982 AD SuperLeicht, 1985 Massi (model unknown), 1988 Daccordi Griffe , 1989 Fauxsin MTB, 1981 Ciocc Mockba, 1992 Bianchi Giro, 1977 Colnago Super
1987 Crest Cannondale, 1987 Basso Gap, 1992 Rossin Performance EL, 1990ish Van Tuyl, 1985 Trek 670, 1982 AD SLE, 2003 Pinarello Surprise, 1990ish MBK Atlantique, 1987 Peugeot Competition, 1987 Nishiki Tri-A, 1981 Faggin, 1996 Cannondale M500, 1984 Mercian, 1982 AD SuperLeicht, 1985 Massi (model unknown), 1988 Daccordi Griffe , 1989 Fauxsin MTB, 1981 Ciocc Mockba, 1992 Bianchi Giro, 1977 Colnago Super
#12
Ride, Wrench, Swap, Race
Join Date: Jan 2010
Location: Northern California
Posts: 9,194
Bikes: Cheltenham-Pedersen racer, Boulder F/S Paris-Roubaix, Varsity racer, '52 Christophe, '62 Continental, '92 Merckx, '75 Limongi, '76 Presto, '72 Gitane SC, '71 Schwinn SS, etc.
Mentioned: 132 Post(s)
Tagged: 0 Thread(s)
Quoted: 1565 Post(s)
Liked 1,296 Times
in
866 Posts
The collars came into being mainly because of the oversized frame tubing that started being used for seat tubes, in conjunction with triple chainrings.
If the crankarm settles inward far enough, the front derailer may not retract inward far enough against an oversized seat tube to effect robust shifting down to the smallest chainring, hence the collars came into being to prevent crankarms settling inward and front derailers no longer quite doing their job.
I haven't tried many different crankarms on the collared crank spindles, so I'm not sure how good of an interference fit can be achieved using this or that crankarm from this or that era. You want to achieve probably a bare minimum of 20 ft-lbs of bolt torque though before the crankarm contacts the collar.
Compressing the collar heavily in a good bench vise, alternately against one pair of flats and then the other pair of flats, may loosen it so it can be pried off.
If the crankarm settles inward far enough, the front derailer may not retract inward far enough against an oversized seat tube to effect robust shifting down to the smallest chainring, hence the collars came into being to prevent crankarms settling inward and front derailers no longer quite doing their job.
I haven't tried many different crankarms on the collared crank spindles, so I'm not sure how good of an interference fit can be achieved using this or that crankarm from this or that era. You want to achieve probably a bare minimum of 20 ft-lbs of bolt torque though before the crankarm contacts the collar.
Compressing the collar heavily in a good bench vise, alternately against one pair of flats and then the other pair of flats, may loosen it so it can be pried off.
Last edited by dddd; 03-24-24 at 07:31 PM.
#13
Senior Member
Join Date: Feb 2020
Posts: 2,820
Mentioned: 49 Post(s)
Tagged: 0 Thread(s)
Quoted: 1106 Post(s)
Likes: 0
Liked 1,328 Times
in
784 Posts
If the crankarm settles inward far enough, the front derailer may not retract inward far enough against an oversized seat tube to effect robust shifting down to the smallest chainring, hence the collars came into being to prevent crankarms settling inward and front derailers no longer quite doing their job.
So if it's used (in the situation you describe) to do so, the axle is too short.
#14
Senior Member
Join Date: May 2008
Location: Fredericksburg, Va
Posts: 9,579
Bikes: '65 Frejus TDF, '73 Bottecchia Giro d'Italia, '83 Colnago Superissimo, '84 Trek 610, '84 Trek 760, '88 Pinarello Veneto, '88 De Rosa Pro, '89 Pinarello Montello, '94 Burley Duet, 97 Specialized RockHopper, 2010 Langster, Tern Link D8
Mentioned: 73 Post(s)
Tagged: 0 Thread(s)
Quoted: 1608 Post(s)
Liked 2,216 Times
in
1,103 Posts
FYSA - The TL-PD40 shown in post #4 came with the pedls. I have one I keep in the box to remind me what it is for.
__________________
Bikes don't stand alone. They are two tired.
Bikes don't stand alone. They are two tired.
#15
Ride, Wrench, Swap, Race
Join Date: Jan 2010
Location: Northern California
Posts: 9,194
Bikes: Cheltenham-Pedersen racer, Boulder F/S Paris-Roubaix, Varsity racer, '52 Christophe, '62 Continental, '92 Merckx, '75 Limongi, '76 Presto, '72 Gitane SC, '71 Schwinn SS, etc.
Mentioned: 132 Post(s)
Tagged: 0 Thread(s)
Quoted: 1565 Post(s)
Liked 1,296 Times
in
866 Posts
The black collar on the Shimano cartridge BB's is made of strong, seemingly hardened steel, and as I mentioned, may require quite forceful methods to remove since you can't really just go blasting it with a torch to loosen it.
As it is provided as a crankarm stop, it is fixed quite solidly onto the spindle.
If you found such a piece made of plastic, what purpose could it serve?
The spindle may in some cases act "too short", as you suggest. Those cases are where 1) Hard jump landings leading to the taper fit loosening, requiring further bolt tightening, and 2) use of oversized seat tube, meaning that as the crank walks up the spindle tapers, you will run out of lo-limit adjustment and the frond derailer won't move in far enough.
Use of a longer spindle length as a solution was actually used, before these collars became standard, but caused problems with excess chainline.
The problem was more of an off-road issue, again because of riders landing from jumps or hitting G-outs with the crankarms horizontal, pushing the square-taper interface to it's designed-in torque limits.
#16
Edumacator
Thread Starter
Join Date: Jan 2018
Location: Goose Creek, SC
Posts: 6,812
Bikes: '87 Crestdale, '87 Basso Gap, '92 Rossin Performance EL-OS, 1990 VanTuyl, 1980s Losa, 1985 Trek 670, 1982 AD SLE, 1987 PX10, etc...
Mentioned: 59 Post(s)
Tagged: 0 Thread(s)
Quoted: 2440 Post(s)
Liked 3,130 Times
in
1,969 Posts
Are you referring to the black "collar" on the pedals, the pictured bottom bracket or perhaps the "Nico and Shimano hubs" that I quote the OP as having initially mentioned?
The black collar on the Shimano cartridge BB's is made of strong, seemingly hardened steel, and as I mentioned, may require quite forceful methods to remove since you can't really just go blasting it with a torch to loosen it.
As it is provided as a crankarm stop, it is fixed quite solidly onto the spindle.
If you found such a piece made of plastic, what purpose could it serve?
The spindle may in some cases act "too short", as you suggest. Those cases are where 1) Hard jump landings leading to the taper fit loosening, requiring further bolt tightening, and 2) use of oversized seat tube, meaning that as the crank walks up the spindle tapers, you will run out of lo-limit adjustment and the frond derailer won't move in far enough.
Use of a longer spindle length as a solution was actually used, before these collars became standard, but caused problems with excess chainline.
The problem was more of an off-road issue, again because of riders landing from jumps or hitting G-outs with the crankarms horizontal, pushing the square-taper interface to it's designed-in torque limits.
The black collar on the Shimano cartridge BB's is made of strong, seemingly hardened steel, and as I mentioned, may require quite forceful methods to remove since you can't really just go blasting it with a torch to loosen it.
As it is provided as a crankarm stop, it is fixed quite solidly onto the spindle.
If you found such a piece made of plastic, what purpose could it serve?
The spindle may in some cases act "too short", as you suggest. Those cases are where 1) Hard jump landings leading to the taper fit loosening, requiring further bolt tightening, and 2) use of oversized seat tube, meaning that as the crank walks up the spindle tapers, you will run out of lo-limit adjustment and the frond derailer won't move in far enough.
Use of a longer spindle length as a solution was actually used, before these collars became standard, but caused problems with excess chainline.
The problem was more of an off-road issue, again because of riders landing from jumps or hitting G-outs with the crankarms horizontal, pushing the square-taper interface to it's designed-in torque limits.
Secondly, does this mean that for practical purposes, most cranks are not going to be happy with the bottom bracket assembly?
__________________
1987 Crest Cannondale, 1987 Basso Gap, 1992 Rossin Performance EL, 1990ish Van Tuyl, 1985 Trek 670, 1982 AD SLE, 2003 Pinarello Surprise, 1990ish MBK Atlantique, 1987 Peugeot Competition, 1987 Nishiki Tri-A, 1981 Faggin, 1996 Cannondale M500, 1984 Mercian, 1982 AD SuperLeicht, 1985 Massi (model unknown), 1988 Daccordi Griffe , 1989 Fauxsin MTB, 1981 Ciocc Mockba, 1992 Bianchi Giro, 1977 Colnago Super
1987 Crest Cannondale, 1987 Basso Gap, 1992 Rossin Performance EL, 1990ish Van Tuyl, 1985 Trek 670, 1982 AD SLE, 2003 Pinarello Surprise, 1990ish MBK Atlantique, 1987 Peugeot Competition, 1987 Nishiki Tri-A, 1981 Faggin, 1996 Cannondale M500, 1984 Mercian, 1982 AD SuperLeicht, 1985 Massi (model unknown), 1988 Daccordi Griffe , 1989 Fauxsin MTB, 1981 Ciocc Mockba, 1992 Bianchi Giro, 1977 Colnago Super