Bent chain stay - possible to bend back?
#1
Member
Thread Starter
Bent chain stay - possible to bend back?
Hello,
This is being sold and was wondering how safe this would be to try and fix/bend back - it is a 531 steel frame, and the bend was not from impact, but from a coaster brake (gone wrong, I guess)?
Cheers.
This is being sold and was wondering how safe this would be to try and fix/bend back - it is a 531 steel frame, and the bend was not from impact, but from a coaster brake (gone wrong, I guess)?
Cheers.
#2
Senior Member
Join Date: Oct 2017
Location: Chapel Hill NC
Posts: 1,683
Bikes: 2000 Litespeed Vortex Chorus 10, 1995 DeBernardi Cromor S/S
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 645 Post(s)
Liked 797 Times
in
446 Posts
given that’s it’s steel, if the price was right I’d certainly take a swing at it. Should be doable with a little forethought, a bench vise and some wood blocks. Looks like both the chain- and seat stay are bent, so I would alternate between the two to slowly rotate the dropout back down. Might need some tweaking to ensure correct wheel alignment. And a second pair of hands might be useful
Last edited by Litespud; 03-20-21 at 06:29 AM.
#3
I'm good to go!
Join Date: Jul 2017
Location: Mississippi
Posts: 15,002
Bikes: Tarmac Disc Comp Di2 - 2020
Mentioned: 51 Post(s)
Tagged: 0 Thread(s)
Quoted: 6198 Post(s)
Liked 4,814 Times
in
3,321 Posts
Unless the frame was being sold for less than $10 USD, I'd pass. Even then I consider how easy I could find another frame with no issues..
However if it were mine, and steel, I'd try bending it back into whatever it took to make the dropouts aligned. I wouldn't try for perfection.
However if it were mine, and steel, I'd try bending it back into whatever it took to make the dropouts aligned. I wouldn't try for perfection.
#4
Senior Member
Join Date: Jul 2014
Location: socal
Posts: 4,266
Mentioned: 9 Post(s)
Tagged: 0 Thread(s)
Quoted: 883 Post(s)
Liked 824 Times
in
623 Posts
Should be safe afterwards, and at least with steel you should be able to see evidence before it fails. I would think you could use a framebuilders jig and get it able to be ridden if not looking perfect.
#5
Full Member
My lbs has the park tool SS-1 stay straightener and has straightened a chain stay for me. That bend is very close to the dropout but it would still probably work. Your lbs could also give you an opinion on the repair.
Likes For mitchmellow62:
#6
Senior Member
Join Date: Jul 2005
Location: Boulder County, CO
Posts: 4,398
Bikes: '80 Masi Gran Criterium, '12 Trek Madone, early '60s Frejus track
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 514 Post(s)
Liked 451 Times
in
339 Posts
I had bent seatstays that were worse than that. I had it straightened and rode the bike three more years, until the brazing at the seat lug cracked. That's when I sprung for replacement and a respray.
The chainstay is bent too, but I would certainly have this straightened and keep riding it, or sell it. If the tubes aren't creased, they is still stronger than the joints it's brazed to, and there's a lot of joint contact at the dropout, unlike a standard seat lug.
The chainstay is bent too, but I would certainly have this straightened and keep riding it, or sell it. If the tubes aren't creased, they is still stronger than the joints it's brazed to, and there's a lot of joint contact at the dropout, unlike a standard seat lug.
#7
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,098
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4211 Post(s)
Liked 3,881 Times
in
2,316 Posts
Some good and less good advice here. I would not use a builder's jig, that's not the jig's purpose and there are faster methods to check alignment as the bending is going along that cost MUCH less. I would do some of the chain stay then some of the seat stay and back a few times to "walk up to" the best final outcome. Fr the best visuals you want to focus the bending focal point to where it is now. The Park tool really won't do this as well as clamped boards will, I have done a combo before though with metal channel clamped to the stays to better locate the bending point. Andy
__________________
AndrewRStewart
AndrewRStewart
#8
Full Member
Join Date: Sep 2012
Location: Palm Springs, California
Posts: 462
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 206 Post(s)
Liked 460 Times
in
176 Posts
It doesn't look like too difficult of a fix. A large C-clamp and some strategically placed blocks of wood, and you could have that straightened out in no time.
#9
Senior Member
Join Date: Jan 2009
Location: San Diego, CA
Posts: 3,677
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 839 Post(s)
Liked 1,064 Times
in
747 Posts
I'm looking at this and thinking it's a little more complicated than just straightening the chain stay as the seat stay is also bent at the dropout and maybe the CS is bent at the BB shell too. Personally I would take it to a pro for an estimate before making a worse mess of this mess. Might not be hugely expensive and well worth the money spent.
#10
Passista
Join Date: Jul 2005
Posts: 7,600
Bikes: 1998 Pinarello Asolo, 1992 KHS Montaña pro, 1980 Raleigh DL-1, IGH Hybrid, IGH Utility
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 868 Post(s)
Liked 721 Times
in
396 Posts
I've straightened worse stays than those using 2 wooden blocks under the stay, 1 on top of it and a lever, with the frame on the floor and using a heavy workbench as a stop, and they came out well.