Seized fixed BB cup....AND stuck cotter
#1
Senior Member
Thread Starter
Join Date: Jul 2006
Location: Oakland, CA
Posts: 1,300
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Seized fixed BB cup....AND stuck cotter
Well, I seem pretty screwed
Trying to strip a Raleigh Grand Prix down to frame. All the parts are junk and will go straight in the trash, doesn't matter if I screw them up.
Driveside cotter won't budge, cotter is now bent, mushroomed, not likely to come out. Only solution I can think of is to drill it out.
I thought maybe I could remove the fixed BB cup without taking off the cotter. The fixed cup is the old style with 16mm flats identical to the adjustable cup side (ie STUPID!). The fixed cup is completely rusted and seized in place and trying to get a grip on the piddly little 16mm flats with a cone wrench just isn't doing it. The flats are already getting damaged.
My only thought is drill out the cotter then start drilling out the fixed cup in several spots and try to get some leverage on it..
Any input?
Trying to strip a Raleigh Grand Prix down to frame. All the parts are junk and will go straight in the trash, doesn't matter if I screw them up.
Driveside cotter won't budge, cotter is now bent, mushroomed, not likely to come out. Only solution I can think of is to drill it out.
I thought maybe I could remove the fixed BB cup without taking off the cotter. The fixed cup is the old style with 16mm flats identical to the adjustable cup side (ie STUPID!). The fixed cup is completely rusted and seized in place and trying to get a grip on the piddly little 16mm flats with a cone wrench just isn't doing it. The flats are already getting damaged.
My only thought is drill out the cotter then start drilling out the fixed cup in several spots and try to get some leverage on it..
Any input?
#2
.
Join Date: Aug 2005
Location: Rocket City, No'ala
Posts: 12,764
Bikes: 2014 Trek Domane 5.2, 1985 Pinarello Treviso, 1990 Gardin Shred, 2006 Bianchi San Jose
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 62 Post(s)
Likes: 0
Liked 29 Times
in
14 Posts
And what will you do when the cups are removed and completely unusable? If you have replacement cups, good for you. If not, your options are limited but still present. My LBS simply used their 68mm 24tpi tap to cut new threads and install a Shimano cartridge bottom bracket for my Sprite.
Drilling out cotters is certainly do able. I've taken an old nail punch and used it with a sledge hammer to remove stubborn cotters. If you can get one cotter off and the cup, you can remove the crankset.
If you are so inclined, drill two holes opposite each other in the cup, insert screws or nails. Use the screws/nails as leverage points for a long screwdriver and unscrew the cup. If that doesn't work, get a longer screwdriver. Have the frame fully immobilized in a workstand or vise. If this doesn't work, take sledgehammer and bash to a pulp the object of your frustration.
Have you considered shopping around for another Grand Prix bicycle that's in far better condition?
Perhaps this project has personal overtones and if so, carry on. If not, perhaps the scrap heap is the next stop for this bicycle. (so says the idiot with five frames awaiting buildup in the garage)
Drilling out cotters is certainly do able. I've taken an old nail punch and used it with a sledge hammer to remove stubborn cotters. If you can get one cotter off and the cup, you can remove the crankset.
If you are so inclined, drill two holes opposite each other in the cup, insert screws or nails. Use the screws/nails as leverage points for a long screwdriver and unscrew the cup. If that doesn't work, get a longer screwdriver. Have the frame fully immobilized in a workstand or vise. If this doesn't work, take sledgehammer and bash to a pulp the object of your frustration.
Have you considered shopping around for another Grand Prix bicycle that's in far better condition?
Perhaps this project has personal overtones and if so, carry on. If not, perhaps the scrap heap is the next stop for this bicycle. (so says the idiot with five frames awaiting buildup in the garage)
#3
Senior Member
Thread Starter
Join Date: Jul 2006
Location: Oakland, CA
Posts: 1,300
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Wait, what BB threading does this thing currently have if its not the standard 68mm diameter with 1.37" x 24tpi thread?
#4
Super Course fan
Join Date: Sep 2006
Location: Lost on the windswept plains of the Great Black Swamp
Posts: 2,720
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 6 Post(s)
Likes: 0
Liked 8 Times
in
8 Posts
If it's a Nottingham made G.P. it's Raleigh 26tpi threaded.
Canadian and most Carlton made G.P.'s are also 26tpi.
If it's a 80's Raleigh USA G.P. it's 24tpi.
Canadian and most Carlton made G.P.'s are also 26tpi.
If it's a 80's Raleigh USA G.P. it's 24tpi.
__________________
I have a white PX-10, a Green Dawes Galaxy and an Orange Falcon, now I'm done.
I have a white PX-10, a Green Dawes Galaxy and an Orange Falcon, now I'm done.
#5
Senior Member
Thread Starter
Join Date: Jul 2006
Location: Oakland, CA
Posts: 1,300
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Well it just gets worse then haha
This is a mid to late 70s GP with the wrap around seat stay. I guess that would make it 26tpi
This is a mid to late 70s GP with the wrap around seat stay. I guess that would make it 26tpi
#6
Senior Member
Thread Starter
Join Date: Jul 2006
Location: Oakland, CA
Posts: 1,300
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Well how about this though
https://www.sheldonbrown.com/raleigh26.html
My GP has its fender eyelet above the dropout
The easiest way to identify Raleigh-built bikes is by looking at the rear dropouts. Almost all Raleigh-threaded bikes have the rear fender eyelets located directly behind the axle, instead of above it. (This doesn't apply to roadsters, which don't generally have dropouts nor fender eyelets.
My GP has its fender eyelet above the dropout
#7
Senior Member
Thread Starter
Join Date: Jul 2006
Location: Oakland, CA
Posts: 1,300
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Well instead of mucking around on the internet about the BB I went downstairs and tried to thread an English 24tpi cup into the frame and what do you know, it works So thats good at least
That still leaves me with the matter then of getting the fixed cup off (now with destruction as a valid option)
That still leaves me with the matter then of getting the fixed cup off (now with destruction as a valid option)
#8
Super Course fan
Join Date: Sep 2006
Location: Lost on the windswept plains of the Great Black Swamp
Posts: 2,720
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 6 Post(s)
Likes: 0
Liked 8 Times
in
8 Posts
Well how about this though
https://www.sheldonbrown.com/raleigh26.html
My GP has its fender eyelet above the dropout
https://www.sheldonbrown.com/raleigh26.html
My GP has its fender eyelet above the dropout
My three G.P's have conventionaly placed eyelets also.
wrap around stays pretty much make it certain you have 26tpi.
Edit: you got real lucky, get us the serial number when you have a chance.
I'll bet it starts with W.
__________________
I have a white PX-10, a Green Dawes Galaxy and an Orange Falcon, now I'm done.
I have a white PX-10, a Green Dawes Galaxy and an Orange Falcon, now I'm done.
#9
Senior Member
Join Date: Mar 2007
Location: Saskatchewan
Posts: 2,465
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 3 Post(s)
Likes: 0
Liked 6 Times
in
5 Posts
Drill out the cotter. They are a soft steel and easy to drill out. I drilled out a pair on my Twenty a few weeks ago.
I use a monster size crescent wrench on fixed side BB's. Its about 3 1/2 feet long and massive.
One crank and out it comes.
This can be done in about 20 minutes.
I use a monster size crescent wrench on fixed side BB's. Its about 3 1/2 feet long and massive.
One crank and out it comes.
This can be done in about 20 minutes.
#10
Still moving forward.
Join Date: Jul 2007
Location: S.F. Peninsula
Posts: 177
Bikes: BF NWT
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I successfully removed a BB very similar to yours from a '74 Raleigh Twenty(26tpi) using Sheldon's fixed cup remover. It consists of a short bolt, washers and a nut. It worked beautifully! You can find it here. BTW, I also tried threading in a 24tpi cup into my BB. It worked fine till about halfway in, and then it stopped dead. So be sure to run it all the way in before deciding that it is a good fit. Good luck!
#11
Senior Member
Thread Starter
Join Date: Jul 2006
Location: Oakland, CA
Posts: 1,300
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I successfully removed a BB very similar to yours from a '74 Raleigh Twenty(26tpi) using Sheldon's fixed cup remover. It consists of a short bolt, washers and a nut. It worked beautifully! You can find it here. BTW, I also tried threading in a 24tpi cup into my BB. It worked fine till about halfway in, and then it stopped dead. So be sure to run it all the way in before deciding that it is a good fit. Good luck!
I don't understand Sheldon's fixed cup removal tool though. It only works with the spindle out, correct? But I can't get the spindle out....
edit: Doh! I can once I get that stupid cotter out
Last edited by BikeManDan; 03-29-08 at 12:20 AM.
#12
Bicycle Repair Man !!!
If the cotter pin is screwed and you will NOT be re-using the cottered axle and crankarm a cut off wheel will remove it in about a minute as all you have to do is cut through the axle.
A hacksaw would also work.
I ran into the same problem when I was upgrading the bb on my Peugeot...the cranks were crap and the cotter pin was toast and after getting frustrated with trying to drive out the pin I just opted to cut it off.
You can still get new 26 tpi cups via Freeman's Cycles in London and finding a tapered axle should not be all that difficult... they also carry these.
A hacksaw would also work.
I ran into the same problem when I was upgrading the bb on my Peugeot...the cranks were crap and the cotter pin was toast and after getting frustrated with trying to drive out the pin I just opted to cut it off.
You can still get new 26 tpi cups via Freeman's Cycles in London and finding a tapered axle should not be all that difficult... they also carry these.
#13
Super Course fan
Join Date: Sep 2006
Location: Lost on the windswept plains of the Great Black Swamp
Posts: 2,720
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 6 Post(s)
Likes: 0
Liked 8 Times
in
8 Posts
That is positively a Raleigh cup, the "N" serial denotes Nottingham production. Everything from Nottingham gets the Raleigh 26tpi cup.
I'd say your bike was made in April of '74
Chart stolen from nlerner (I think),
I'd say your bike was made in April of '74
Chart stolen from nlerner (I think),
__________________
I have a white PX-10, a Green Dawes Galaxy and an Orange Falcon, now I'm done.
I have a white PX-10, a Green Dawes Galaxy and an Orange Falcon, now I'm done.
#14
Senior Member
Thread Starter
Join Date: Jul 2006
Location: Oakland, CA
Posts: 1,300
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Well gents, appreciate the help.
So I think what I'll be doing tomorrow is working to salvage the cups (given that they're not pitted). I'll hacksaw the whole spindle (thanks for that, forgot about that option), and then construct a Sheldon fixed cup remover™
So I think what I'll be doing tomorrow is working to salvage the cups (given that they're not pitted). I'll hacksaw the whole spindle (thanks for that, forgot about that option), and then construct a Sheldon fixed cup remover™
#15
Senior Member
Join Date: Jul 2000
Location: Snowy midwest
Posts: 5,391
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
There are few things as frustrating as frozen cotters. Man, I have been where you are with the mushroomed cotters. Whoever thought of that design was really thinking short-term maintanance.
One thing to consider is that if you mushroomed your cotters, I GUESS that you might not have used a support under the crank while you were whacking the cotters. The preferred method (which Sheldon taught me) is to make a wood block with a "V" cut in it to support the crank arm and to use a hardened punch when smacking the cotter. I used an old pedal axle for a punch and it works more often than not.
Anyway, if you did not use a block under the crank arm, it is quite possible that you damaged the bearing cups in the BB with violently banging on the crank with a hammer. You might consider this as you plan your path forward.
I might have some Raleigh crank spindles if you need one for the project. Drop me a line and I can look if you need one.
One thing to consider is that if you mushroomed your cotters, I GUESS that you might not have used a support under the crank while you were whacking the cotters. The preferred method (which Sheldon taught me) is to make a wood block with a "V" cut in it to support the crank arm and to use a hardened punch when smacking the cotter. I used an old pedal axle for a punch and it works more often than not.
Anyway, if you did not use a block under the crank arm, it is quite possible that you damaged the bearing cups in the BB with violently banging on the crank with a hammer. You might consider this as you plan your path forward.
I might have some Raleigh crank spindles if you need one for the project. Drop me a line and I can look if you need one.
#16
Bike Dealer since 1972
Join Date: Dec 2007
Location: Eastern North Carolina
Posts: 288
Bikes: Some of the bikes I've collected: Raleighs ( about 20), Trek ( oldest 1978 770 Columbus tubes), Mercian, Condor, Bob Jackson, Falcon, Holdsworth, Jacques Anquetil, Bianchi, LeMond, Cannondale, Schwinn, Iver Johnson, Dunelt
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 18 Post(s)
Likes: 0
Liked 71 Times
in
29 Posts
If you can't use the existing cups check with your LBS. See if they have a threadless repair bottom bracket that is made to go in a bb when the the threads are stripped out.
There are several axle lengths. Heres a link
https://74.8.32.132/nondealer/view.ph...ETS%3A+PYRAMID
There are several axle lengths. Heres a link
https://74.8.32.132/nondealer/view.ph...ETS%3A+PYRAMID
#17
Junior Member
Join Date: Jul 2005
Posts: 5
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
If Sheldon's BigBolt method won't get the fixed cup out, this will.
https://www.bikesmithdesign.com/BBTool/
https://www.bikesmithdesign.com/BBTool/
#18
holyrollin'
I'd clamp my big ViseGrip onto the wide (mushroomed) end of the cotter as tightly as possible and proceed to bash it out with a hammer. You've little hope that the bearings have not been damaged, and this percussive therapy may even help to loosen the fixed cup. Penetrating oil a plus.
#19
Senior Member
Thread Starter
Join Date: Jul 2006
Location: Oakland, CA
Posts: 1,300
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
If Sheldon's BigBolt method won't get the fixed cup out, this will.
https://www.bikesmithdesign.com/BBTool/
https://www.bikesmithdesign.com/BBTool/
Tried to hacksaw through the spindle and my measly hacksaw proved inadequate. Dremel with a cut off wheel did a much better job but because of the awkward angle I can't get all the way through it. Wish I had a Sawzall
#20
Dolce far niente
Join Date: Dec 2004
Location: Northern CA
Posts: 10,704
Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
Quoted: 20 Post(s)
Likes: 0
Liked 17 Times
in
14 Posts
Pack the BB with black powder, from the non-drive side. There won't be anything left, but it'll be fun - as well as a bit cathartic.
Then have Stringbreaker send you some of his found beer, and toast your triumph over British engineering.
Then have Stringbreaker send you some of his found beer, and toast your triumph over British engineering.
__________________
"Love is not the dying moan of a distant violin, it’s the triumphant twang of a bedspring."
S. J. Perelman
"Love is not the dying moan of a distant violin, it’s the triumphant twang of a bedspring."
S. J. Perelman
#21
surly old man
Join Date: Sep 2006
Location: Carlisle, PA
Posts: 3,392
Bikes: IRO Mark V, Karate Monkey half fat, Trek 620 IGH, Cannondale 26/24 MTB, Amp Research B3, and more.
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 46 Post(s)
Likes: 0
Liked 42 Times
in
18 Posts
Sheldon's big bolt trick ALWAYS works.
jim
jim
__________________
Cross Check Nexus7, IRO Mark V, Trek 620 Nexus7, Karate Monkey half fat, IRO Model 19 fixed, Amp Research B3, Surly 1x1 half fat fixed, and more...
--------------------------
SB forever
Cross Check Nexus7, IRO Mark V, Trek 620 Nexus7, Karate Monkey half fat, IRO Model 19 fixed, Amp Research B3, Surly 1x1 half fat fixed, and more...
--------------------------
SB forever
#22
Senior Member
Join Date: Jul 2000
Location: Snowy midwest
Posts: 5,391
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
I saw that tool once in my internet travels, thanks for posting it again. Seriously considering purchasing it now...
Tried to hacksaw through the spindle and my measly hacksaw proved inadequate. Dremel with a cut off wheel did a much better job but because of the awkward angle I can't get all the way through it. Wish I had a Sawzall
Tried to hacksaw through the spindle and my measly hacksaw proved inadequate. Dremel with a cut off wheel did a much better job but because of the awkward angle I can't get all the way through it. Wish I had a Sawzall
#23
Senior Member
Join Date: Nov 2006
Posts: 92
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Well, I seem pretty screwed
Trying to strip a Raleigh Grand Prix down to frame. All the parts are junk and will go straight in the trash, doesn't matter if I screw them up.
Driveside cotter won't budge, cotter is now bent, mushroomed, not likely to come out. Only solution I can think of is to drill it out.
I thought maybe I could remove the fixed BB cup without taking off the cotter. The fixed cup is the old style with 16mm flats identical to the adjustable cup side (ie STUPID!). The fixed cup is completely rusted and seized in place and trying to get a grip on the piddly little 16mm flats with a cone wrench just isn't doing it. The flats are already getting damaged.
My only thought is drill out the cotter then start drilling out the fixed cup in several spots and try to get some leverage on it..
Any input?
Trying to strip a Raleigh Grand Prix down to frame. All the parts are junk and will go straight in the trash, doesn't matter if I screw them up.
Driveside cotter won't budge, cotter is now bent, mushroomed, not likely to come out. Only solution I can think of is to drill it out.
I thought maybe I could remove the fixed BB cup without taking off the cotter. The fixed cup is the old style with 16mm flats identical to the adjustable cup side (ie STUPID!). The fixed cup is completely rusted and seized in place and trying to get a grip on the piddly little 16mm flats with a cone wrench just isn't doing it. The flats are already getting damaged.
My only thought is drill out the cotter then start drilling out the fixed cup in several spots and try to get some leverage on it..
Any input?
#24
wheelin in the years
Join Date: Jul 2005
Location: Kansas
Posts: 666
Bikes: Some Schwinns, a Gary Fisher, some vintage lt wts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
I have used Sheldon's removal bolt tool a couple of times, the last time though It slipped. So I used an arc welder and put a couple of spot welds on the bolt to the cup. Then put it in a bench top vice, and used the frame to spin it out. This may be an option if you plan on not re-using the cup,and can get a sopot weld on what is left of your spendel
#25
Senior Member
Thread Starter
Join Date: Jul 2006
Location: Oakland, CA
Posts: 1,300
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Or I can just break out the plasma cutter
Wish I had those kind of toys but nope, no welder, no cutters.
And you're right, 385xza, 5/8th flats, silly Brits
Wish I had those kind of toys but nope, no welder, no cutters.
And you're right, 385xza, 5/8th flats, silly Brits