Handlebar question regarding length
#1
Junior Member
Thread Starter
Join Date: Apr 2023
Location: 33.85485, -78.53622
Posts: 99
Bikes: A Janky Schwinn
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 59 Post(s)
Likes: 0
Liked 17 Times
in
14 Posts
Handlebar question regarding length
Are the markings I see on higher quality bars near the ends there as 'cut' marks if you choose to shorten them?
Thanks,
Aaron
Thanks,
Aaron
#2
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,100
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4212 Post(s)
Liked 3,883 Times
in
2,318 Posts
I suspect they are guide line markings. I would not trust a cut's location based on a applied marking and prefer to measure. Just last week a fellow wrench was installing a new bar on a bike that had been in for a fitting. The bar's central stem clamping markings were off center by about 8-10mm. Andy
__________________
AndrewRStewart
AndrewRStewart
Likes For Andrew R Stewart:
#3
Junior Member
Thread Starter
Join Date: Apr 2023
Location: 33.85485, -78.53622
Posts: 99
Bikes: A Janky Schwinn
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 59 Post(s)
Likes: 0
Liked 17 Times
in
14 Posts
I have ordered 800mm bars which I am guessing will be wider than I need. I will carefully cut them to the width I need.
NOW. I am finding that you need to do the same with a fork steering tube.
I have no issues with doing this. I have the tools and knowledge and I quite like it.
NOW. I am finding that you need to do the same with a fork steering tube.
I have no issues with doing this. I have the tools and knowledge and I quite like it.
#4
Clark W. Griswold
Join Date: Mar 2014
Location: ,location, location
Posts: 13,558
Bikes: Foundry Chilkoot Ti W/Ultegra Di2, Salsa Timberjack Ti, Cinelli Mash Work RandoCross Fun Time Machine, 1x9 XT Parts Hybrid, Co-Motion Cascadia, Specialized Langster, Phil Wood Apple VeloXS Frame (w/DA 7400), R+M Supercharger2 Rohloff, Habanero Ti 26
Mentioned: 54 Post(s)
Tagged: 0 Thread(s)
Quoted: 4365 Post(s)
Liked 4,006 Times
in
2,675 Posts
Yes those lines are cutting guides and you do not want to go below them as the bars are reinforced in certain places for all the controls so going too far in could cause issues. Steerer tubes may or may not need to be cut depending on the fit you are looking to achieve.
HoweAndrew R Stewart said it is always good to measure. As they say measure twice cut once.
HoweAndrew R Stewart said it is always good to measure. As they say measure twice cut once.
#6
Senior Member
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656
Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!
Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,096 Times
in
742 Posts
If there are symmetrical markings near the bar's center, they are for centering it in the stem and for setting rotation. If the markings are near the bar's ends, they are for trimming to length. In either case measure to be sure the markings are properly positioned.
#7
I'm good to go!
Join Date: Jul 2017
Location: Mississippi
Posts: 15,002
Bikes: Tarmac Disc Comp Di2 - 2020
Mentioned: 51 Post(s)
Tagged: 0 Thread(s)
Quoted: 6199 Post(s)
Liked 4,816 Times
in
3,323 Posts
I expect that different bars and bars from different manufacturers might have marks on them for different reasons.
#9
Junior Member
Thread Starter
Join Date: Apr 2023
Location: 33.85485, -78.53622
Posts: 99
Bikes: A Janky Schwinn
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 59 Post(s)
Likes: 0
Liked 17 Times
in
14 Posts
Yes those lines are cutting guides and you do not want to go below them as the bars are reinforced in certain places for all the controls so going too far in could cause issues. Steerer tubes may or may not need to be cut depending on the fit you are looking to achieve.
HoweAndrew R Stewart said it is always good to measure. As they say measure twice cut once.
HoweAndrew R Stewart said it is always good to measure. As they say measure twice cut once.
#10
Clark W. Griswold
Join Date: Mar 2014
Location: ,location, location
Posts: 13,558
Bikes: Foundry Chilkoot Ti W/Ultegra Di2, Salsa Timberjack Ti, Cinelli Mash Work RandoCross Fun Time Machine, 1x9 XT Parts Hybrid, Co-Motion Cascadia, Specialized Langster, Phil Wood Apple VeloXS Frame (w/DA 7400), R+M Supercharger2 Rohloff, Habanero Ti 26
Mentioned: 54 Post(s)
Tagged: 0 Thread(s)
Quoted: 4365 Post(s)
Liked 4,006 Times
in
2,675 Posts
If you are buying that expensive of a handlebar you are probably buying the wrong bar. Buying a very expensive handlebar is for someone who knows the position they need and has everything dialed. If you aren't dialed get something decent enough but not expensive and in the case of my old 90s mountain bike build the cheaper handlebars were actually A LOT lighter than the Sakae PowerBulge bars I had put on it but the bike was ti and so why shouldn't the handlebars?
#11
Senior Member
Join Date: Feb 2022
Location: GMT-5
Posts: 944
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 540 Post(s)
Liked 416 Times
in
274 Posts
If it isn't going to be used for downhill enduro, cut it as you see fit. The markers are just to help you cut equally.
Note: Keep about an inch more than what you think you prefer. After a few rides, then you can go ahead and cut off the extra. Because you can't do for the opposite.