Re riveting a cassette
#1
Senior Member
Thread Starter
Join Date: Dec 2004
Posts: 1,102
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 567 Post(s)
Liked 660 Times
in
389 Posts
Re riveting a cassette
I was mis shifting and thought I bent a ring.
Upon inspection I notice one ring was completely loose of a rivet.
I guess I could re rivet the whole damn thing.
Is there any obvious reason I should not?
Upon inspection I notice one ring was completely loose of a rivet.
I guess I could re rivet the whole damn thing.
Is there any obvious reason I should not?
#2
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,106
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4215 Post(s)
Liked 3,892 Times
in
2,323 Posts
Yes. You might not have the tooling or skills. or you might not be able to create a rivet with the minimal heads that the common cassette ones have. (Specific rivets for the application using distinct anvil and die for forming the heads just so. These are no pop rivets. Andy
__________________
AndrewRStewart
AndrewRStewart
Likes For Andrew R Stewart:
#3
Senior Member
Join Date: Dec 2016
Location: Long Island, NY
Posts: 2,119
Bikes: Trek 800 x 2, Schwinn Heavy Duti, Schwinn Traveler, Schwinn Le Tour Luxe, Schwinn Continental, Cannondale M400 and Lambert, Schwinn Super Sport
Mentioned: 14 Post(s)
Tagged: 0 Thread(s)
Quoted: 812 Post(s)
Liked 1,028 Times
in
668 Posts
The rivets are to keep the assembly together at the factory. You don't really need the rivets and I have removed them when I clean a cassette. All the cogs must be flat. If one of them is bent or otherwise out of shape, it might be easiest to get a new cassette.
Likes For Velo Mule:
#4
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,106
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4215 Post(s)
Liked 3,892 Times
in
2,323 Posts
Unless the rivet in question is joining the cog with a spyder/carrier. Andy
__________________
AndrewRStewart
AndrewRStewart
Likes For Andrew R Stewart:
#5
Senior Member
Join Date: Dec 2016
Location: Long Island, NY
Posts: 2,119
Bikes: Trek 800 x 2, Schwinn Heavy Duti, Schwinn Traveler, Schwinn Le Tour Luxe, Schwinn Continental, Cannondale M400 and Lambert, Schwinn Super Sport
Mentioned: 14 Post(s)
Tagged: 0 Thread(s)
Quoted: 812 Post(s)
Liked 1,028 Times
in
668 Posts
So, @CrimsonEclipse, can you get a picture. Everything works better with pictures.
#6
Senior Member
Thread Starter
Join Date: Dec 2004
Posts: 1,102
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 567 Post(s)
Liked 660 Times
in
389 Posts
Ahh, good point. I was thinking straight through rivets. I didn't think about those spider rivets.
So, @CrimsonEclipse, can you get a picture. Everything works better with pictures.
So, @CrimsonEclipse, can you get a picture. Everything works better with pictures.
Rivet pulled out.
There's room for a standard solid rivet head between the cogs and won't interfere with the chain.
Yeah, it's a carrier connecting the 3 largest cogs.
None of the cogs look bent, just the third one pulled loose.
edit:
Steel rivet, 4.3mm or 5/32 diameter.
Not sure I want to replace a solid steel rivet with an aluminum one.
Last edited by CrimsonEclipse; 04-12-24 at 08:54 PM.
#7
Senior Member
Join Date: Nov 2010
Location: Sacramento, CA
Posts: 22,990
Bikes: old ones
Mentioned: 304 Post(s)
Tagged: 0 Thread(s)
Quoted: 26441 Post(s)
Liked 10,406 Times
in
7,225 Posts
.
...McMaster Carr sells solid steel rivets, and it's not that hard to do a not so neat job of ponding one in there, and doming the insertion side.
But I'm not sure of the minimum quantity, which might cost you more than a new cassette. I would try my local commercial fasteners place, where they sell stuff like this in whatever quantity I request.
...McMaster Carr sells solid steel rivets, and it's not that hard to do a not so neat job of ponding one in there, and doming the insertion side.
But I'm not sure of the minimum quantity, which might cost you more than a new cassette. I would try my local commercial fasteners place, where they sell stuff like this in whatever quantity I request.
#8
Senior Member
Join Date: Apr 2011
Posts: 7,136
Mentioned: 41 Post(s)
Tagged: 0 Thread(s)
Quoted: 4450 Post(s)
Liked 1,587 Times
in
1,046 Posts
I doubt an aluminum rivet will fail before the cassette is worn out.