Drivetrain Advice
#26
Banned
most replacement freewheels these days have the hyperglide tooth profile,
the side ramps and shortened tooth makes early shifting..
tall teeth and late shifting and friction levers depended on the hand skills of the rider ..
I like the way tall tooth freewheels dont autoshift , like the new ones do, when the lever is not indexed.
..and the index stuff all in alignment and adjustment, becomes a separate complication..
980 is the lower consumer part, GS and Record priced above it.
the side ramps and shortened tooth makes early shifting..
tall teeth and late shifting and friction levers depended on the hand skills of the rider ..
I like the way tall tooth freewheels dont autoshift , like the new ones do, when the lever is not indexed.
..and the index stuff all in alignment and adjustment, becomes a separate complication..
980 is the lower consumer part, GS and Record priced above it.
#27
working on my sandal tan
Join Date: Aug 2011
Location: CID
Posts: 22,629
Bikes: 1991 Bianchi Eros, 1964 Armstrong, 1988 Diamondback Ascent, 1988 Bianchi Premio, 1987 Bianchi Sport SX, 1980s Raleigh mixte (hers), All-City Space Horse (hers)
Mentioned: 98 Post(s)
Tagged: 0 Thread(s)
Quoted: 3871 Post(s)
Liked 2,568 Times
in
1,579 Posts
It could be that the 15T now behaves like a cog that's seen elogated chains because of the grinding. After some more wear near the bottom of the tooth, it may start to behave normally...
They make 13-14-15-17-19-21-23 HyperGlide cassettes, too -- something to consider if you find yourself with a 7-speed cassette wheel. It's my gearing of choice now.
They make 13-14-15-17-19-21-23 HyperGlide cassettes, too -- something to consider if you find yourself with a 7-speed cassette wheel. It's my gearing of choice now.
#28
Ride, Wrench, Swap, Race
Join Date: Jan 2010
Location: Northern California
Posts: 9,194
Bikes: Cheltenham-Pedersen racer, Boulder F/S Paris-Roubaix, Varsity racer, '52 Christophe, '62 Continental, '92 Merckx, '75 Limongi, '76 Presto, '72 Gitane SC, '71 Schwinn SS, etc.
Mentioned: 132 Post(s)
Tagged: 0 Thread(s)
Quoted: 1565 Post(s)
Liked 1,296 Times
in
866 Posts
Can't tell from the photo, other than that the bevels look more than adequate.
In the case of not grinding enough, the chain usually will wear in to a solid engagement with the sprocket in a couple or few hundred miles.
If you took too much off, possibly you could find someone with the one 15t sprocket.
Glad to hear the bike is running well.
EDIT: Seeing ThermionicScott's post just now, sounds like a possibility it'll wear into perfection either way.
In the case of not grinding enough, the chain usually will wear in to a solid engagement with the sprocket in a couple or few hundred miles.
If you took too much off, possibly you could find someone with the one 15t sprocket.
Glad to hear the bike is running well.
EDIT: Seeing ThermionicScott's post just now, sounds like a possibility it'll wear into perfection either way.
#29
Senior Member
Join Date: Nov 2012
Location: Seattle
Posts: 1,085
Bikes: Frejus/Bertin/Cannondale
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
I like the Cyclone stuff a lot, but for the absolute best, find a XC Pro front & a Superbe Pro rear. The Super Bee handles a 28t in the back easily, but I only use 5 gears in back. I'm 90% sure the XC Pro will handle a tricky triple up front too. Right now I'm running a 50/34 double setup, on a triple Race Face crank, and it "looks" like it'll handle a little 24t granny gear I have too, once I find the right chainring washers/spacers. The thing is, it's on a BB spindle that clearly says "for doubles only" on the web, so it shouldn't work.
#30
The Brutally Handsome
Thread Starter
Join Date: Jun 2007
Location: Siberia
Posts: 508
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 2 Times
in
2 Posts
Sounds like a good combo. I actually had some Superbe Pro shifters but I stored them very poorly and lost some of the critical small-parts.
#31
Extraordinary Magnitude
Join Date: Aug 2009
Location: Waukesha WI
Posts: 13,648
Bikes: 1978 Trek TX700; 1978/79 Trek 736; 1984 Specialized Stumpjumper Sport; 1984 Schwinn Voyageur SP; 1985 Trek 620; 1985 Trek 720; 1986 Trek 400 Elance; 1987 Schwinn High Sierra; 1990 Miyata 1000LT
Mentioned: 84 Post(s)
Tagged: 0 Thread(s)
Quoted: 2608 Post(s)
Liked 1,703 Times
in
937 Posts
I like the Cyclone stuff a lot, but for the absolute best, find a XC Pro front & a Superbe Pro rear. The Super Bee handles a 28t in the back easily, but I only use 5 gears in back. I'm 90% sure the XC Pro will handle a tricky triple up front too. Right now I'm running a 50/34 double setup, on a triple Race Face crank, and it "looks" like it'll handle a little 24t granny gear I have too, once I find the right chainring washers/spacers. The thing is, it's on a BB spindle that clearly says "for doubles only" on the web, so it shouldn't work.
The Superbe Pro- I think one of the prettiest pieces of bike hardware evAr- doesn't handle a 30- from my experience. It won't adjust far enough down to clear the 30- so it grinds. The XC Pro and Comp do. Marvelously. For whatever it's worth- I have had a medium cage Pro and a long cage Comp working on either 32 or 34 (I should count those teeth one of these days).
Although much of that is out of what Sizzle-Chest needs.
__________________
*Recipient of the 2006 Time Magazine "Person Of The Year" Award*
Commence to jigglin’ huh?!?!
"But hey, always love to hear from opinionated amateurs." -says some guy to Mr. Marshall.
Commence to jigglin’ huh?!?!
"But hey, always love to hear from opinionated amateurs." -says some guy to Mr. Marshall.
Last edited by The Golden Boy; 12-21-13 at 10:31 AM.
Thread
Thread Starter
Forum
Replies
Last Post
zukahn1
Classic and Vintage Bicycles: Whats it Worth? Appraisals.
2
08-05-16 10:19 AM
jjames1452
Classic and Vintage Bicycles: Whats it Worth? Appraisals.
18
10-13-13 05:21 AM