Correct distance between top of threaded headset and fork steerer?
#1
Senior Member
Thread Starter
Correct distance between top of threaded headset and fork steerer?
Planning a quill setup. Have read about 1inch threaded headsets and their stack height vs fork steerer length minus head tube length.
Q. When the headset top/lock-nut? is screwed down properly, do you ideally want the top edge of the fork to be sitting a mm or so below the headset top face?
Q. When the headset top/lock-nut? is screwed down properly, do you ideally want the top edge of the fork to be sitting a mm or so below the headset top face?
#2
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,160
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4236 Post(s)
Liked 3,963 Times
in
2,359 Posts
Not sure of the specifics of the question but if the top nut/lock nut has a lip (and most do) that covers the top edge of the steerer than that steerer has to be at least short enough to clear the underside of that lip. By how much is not the issue as long there's enough thread overlap and the steerer doesn't contact that lip. This usually has a couple/three mm range.
What is meant by "headset top face"? Andy
What is meant by "headset top face"? Andy
__________________
AndrewRStewart
AndrewRStewart
Likes For Andrew R Stewart:
#3
Senior Member
Join Date: Jan 2009
Location: San Diego, CA
Posts: 3,738
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 862 Post(s)
Liked 1,105 Times
in
770 Posts
And if the steerer is a few millimeters too long then add some spacers between the adjuster nut and the lock nut for future proofing for headsets with taller stack heights rather than cut the steerer to fit your current HS.
#4
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,160
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4236 Post(s)
Liked 3,963 Times
in
2,359 Posts
Unless you are dealing with a CK GripNut design which has no allowance for added spacers... Andy
__________________
AndrewRStewart
AndrewRStewart
Likes For Andrew R Stewart:
#5
cowboy, steel horse, etc
Join Date: Sep 2008
Location: The hot spot.
Posts: 45,166
Bikes: everywhere
Mentioned: 74 Post(s)
Tagged: 1 Thread(s)
Quoted: 12970 Post(s)
Liked 7,888 Times
in
4,194 Posts
I like about 20mm to an inch of spacers between locknut and cup/cone because I like fairly high bars.
And if you're asking if top of locknut should be above the top of the steerer, yes. Even if the locknut doesn't have an interior flange I'll leave a couple of threads on the locknut unused.
Someday I'll paint this spacer (cut from threadless steel 1-1/8" steerer) and top cup...
And if you're asking if top of locknut should be above the top of the steerer, yes. Even if the locknut doesn't have an interior flange I'll leave a couple of threads on the locknut unused.
Someday I'll paint this spacer (cut from threadless steel 1-1/8" steerer) and top cup...
Last edited by LesterOfPuppets; 09-30-23 at 06:24 PM.
Likes For LesterOfPuppets:
#6
Senior Member
Thread Starter
Not sure of the specifics of the question but if the top nut/lock nut has a lip (and most do) that covers the top edge of the steerer than that steerer has to be at least short enough to clear the underside of that lip. By how much is not the issue as long there's enough thread overlap and the steerer doesn't contact that lip. This usually has a couple/three mm range.
What is meant by "headset top face"? Andy
What is meant by "headset top face"? Andy
#7
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,160
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4236 Post(s)
Liked 3,963 Times
in
2,359 Posts
I like about 20mm to an inch of spacers between locknut and cup/cone because I like fairly high bars.
And if you're asking if top of locknut should be above the top of the steerer, yes. Even if the locknut doesn't have an interior flange I'll leave a couple of threads on the locknut unused.
Someday I'll paint this spacer (cut from threadless steel 1-1/8" steerer) and top cup...
And if you're asking if top of locknut should be above the top of the steerer, yes. Even if the locknut doesn't have an interior flange I'll leave a couple of threads on the locknut unused.
Someday I'll paint this spacer (cut from threadless steel 1-1/8" steerer) and top cup...
__________________
AndrewRStewart
AndrewRStewart
Likes For Andrew R Stewart:
#8
Senior Member
Join Date: Aug 2009
Posts: 1,884
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 525 Post(s)
Liked 691 Times
in
404 Posts
I like about 20mm to an inch of spacers between locknut and cup/cone because I like fairly high bars.
And if you're asking if top of locknut should be above the top of the steerer, yes. Even if the locknut doesn't have an interior flange I'll leave a couple of threads on the locknut unused.
Someday I'll paint this spacer (cut from threadless steel 1-1/8" steerer) and top cup...
And if you're asking if top of locknut should be above the top of the steerer, yes. Even if the locknut doesn't have an interior flange I'll leave a couple of threads on the locknut unused.
Someday I'll paint this spacer (cut from threadless steel 1-1/8" steerer) and top cup...
#9
aged to perfection
Join Date: Jun 2009
Location: PacNW
Posts: 1,871
Bikes: Dinucci Allez 2.0, Richard Sachs, Alex Singer, Serotta, Masi GC, Raleigh Pro Mk.1, Hetchins, etc
Mentioned: 24 Post(s)
Tagged: 0 Thread(s)
Quoted: 863 Post(s)
Liked 1,298 Times
in
686 Posts
I think he means - if the stem is removed, is there a gap between the top of the steerer tube and the inside of the top nut.
you want full engagement on the threads. If the nut and upper cup are tightly locked together and there's no play, look for about a 1 mm gap inside the nut. You do not want the nut bottomed out on the steerer.
/markp
you want full engagement on the threads. If the nut and upper cup are tightly locked together and there's no play, look for about a 1 mm gap inside the nut. You do not want the nut bottomed out on the steerer.
/markp
Likes For mpetry912:
#10
señor miembro
Join Date: Dec 2018
Location: Pac NW
Posts: 6,687
Bikes: '70s - '80s Campagnolo
Mentioned: 93 Post(s)
Tagged: 0 Thread(s)
Quoted: 3936 Post(s)
Liked 6,618 Times
in
3,275 Posts
#11
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,160
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4236 Post(s)
Liked 3,963 Times
in
2,359 Posts
Because life is not perfect and the spacers needed to get 2mm VS 1mm of gap might not be at hand. Since both achieve the same mechanical result...Andy
__________________
AndrewRStewart
AndrewRStewart