High end Alloy Wheelsets w/ Cup and Cone Bearings?
#2
Senior Member
Join Date: Dec 2009
Location: Melbourne, Oz
Posts: 9,547
Bikes: https://weightweenies.starbike.com/forum/viewtopic.php?f=10&t=152015&p=1404231
Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
Quoted: 1529 Post(s)
Liked 718 Times
in
510 Posts
That's it, AFAIK. Sucks, but unfortunately plenty of folks see nothing wrong with cartridge bearings in hubs, so there you go.
Out of the two, Shimano has the best design IMO, due to the cassette body being a stressed member that places the drive side axle bearing next to the dropout where it belongs. Unlike Campy, Shimano also uses cup and cone bearings for the cassette body, which are adjustable via shims, if you can crack open the cassette body (two notches in the bearing cup, left hand thread).
Mavic hubs are only cartridge bearing, and most have a poxy bushing for the inboard cassette body bearing, but at least their drive side axle bearing is towards the dropout.
If you could find a brand that uses angular contact cartridge bearings with adjustable preload, that'd be sign there's been some actual engineering done instead of this cookie cutter crap that passes for hub internals these days... Not sure anybody's bothered though.
BTW, 'high end alloy wheelset' is getting to be a bit of an oxymoron these days. Shimano's ally/carbon rims are pretty damn nice, but I'm not sure if they've got around to doing them wider like everyone wants now.
Out of the two, Shimano has the best design IMO, due to the cassette body being a stressed member that places the drive side axle bearing next to the dropout where it belongs. Unlike Campy, Shimano also uses cup and cone bearings for the cassette body, which are adjustable via shims, if you can crack open the cassette body (two notches in the bearing cup, left hand thread).
Mavic hubs are only cartridge bearing, and most have a poxy bushing for the inboard cassette body bearing, but at least their drive side axle bearing is towards the dropout.
If you could find a brand that uses angular contact cartridge bearings with adjustable preload, that'd be sign there's been some actual engineering done instead of this cookie cutter crap that passes for hub internals these days... Not sure anybody's bothered though.
BTW, 'high end alloy wheelset' is getting to be a bit of an oxymoron these days. Shimano's ally/carbon rims are pretty damn nice, but I'm not sure if they've got around to doing them wider like everyone wants now.
Last edited by Kimmo; 05-27-21 at 03:31 AM.
#4
Senior Member
Join Date: Nov 2014
Location: Eugene, Oregon, USA
Posts: 27,547
Mentioned: 217 Post(s)
Tagged: 0 Thread(s)
Quoted: 18378 Post(s)
Liked 4,512 Times
in
3,354 Posts
Perhaps @Kimmo gave a good answer
Shimano still sells most of their J-Bend hubs as individual hubs. I don't believe their straight-pull hubs are typically sold bare. But, there are options to build your own wheels.
Shimano's new cone lock is kind of cool, although the adjustment takes some getting used to, and they have good Labyrinth seals.
Shimano still sells most of their J-Bend hubs as individual hubs. I don't believe their straight-pull hubs are typically sold bare. But, there are options to build your own wheels.
Shimano's new cone lock is kind of cool, although the adjustment takes some getting used to, and they have good Labyrinth seals.
#5
Senior Member
Join Date: Dec 2009
Location: Melbourne, Oz
Posts: 9,547
Bikes: https://weightweenies.starbike.com/forum/viewtopic.php?f=10&t=152015&p=1404231
Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
Quoted: 1529 Post(s)
Liked 718 Times
in
510 Posts
You could buy a worn out set of Shimano wheels with the 16/20 (or 16/21) straight pull hubs (as long as the cones are still good, replacements can be hard to source, but if they're properly adjusted they should last almost forever) and lace them to whatever rims you like. I've actually never seen this done, but it should be common IMO.
#6
Sunshine
Join Date: Aug 2014
Location: Des Moines, IA
Posts: 16,616
Bikes: '18 class built steel roadbike, '19 Fairlight Secan, '88 Schwinn Premis , Black Mountain Cycles Monstercross V4, '89 Novara Trionfo
Mentioned: 123 Post(s)
Tagged: 0 Thread(s)
Quoted: 10966 Post(s)
Liked 7,493 Times
in
4,189 Posts
The one answer given is what i would have posted. I'm guessing it's what others would have posted too.
No point in a bunch of people posting the same comment over and again.
Get some shimano hubs, choose a quality rim with 32 holes, and use some double butted spokes.
No point in a bunch of people posting the same comment over and again.
Get some shimano hubs, choose a quality rim with 32 holes, and use some double butted spokes.
Likes For mstateglfr:
#7
Senior Member
Join Date: Sep 2017
Posts: 7,887
Mentioned: 38 Post(s)
Tagged: 0 Thread(s)
Quoted: 6972 Post(s)
Liked 10,970 Times
in
4,692 Posts
You could buy a worn out set of Shimano wheels with the 16/20 (or 16/21) straight pull hubs (as long as the cones are still good, replacements can be hard to source, but if they're properly adjusted they should last almost forever) and lace them to whatever rims you like. I've actually never seen this done, but it should be common IMO.
#8
Senior Member
Just for completeness - Fulcrum hubs have cup/cone bearings as well. That said, they're owned by Campagnolo, so while it's a separate brand, not actually a separate company.
(and my Zondas appear to have been stuck in customs for the past week... but at least they were in-stock and appear to have shipped out of PBK's warehouse...)
(and my Zondas appear to have been stuck in customs for the past week... but at least they were in-stock and appear to have shipped out of PBK's warehouse...)
#10
Senior Member
Wheels below the Zonda or Fulcrum racing 3 use cartridge bearings.
#11
Senior Member
They do. One of the sites I looked at (maybe CyclingTips?) did a teardown and showed that the Fulcrum Racing 5 was cartridge bearings, but the Racing 3 and Racing 0 had balls inside.
Edit: Corrected myself - DaveSSS had it right, it's the Racing 3 and Racing 0 that have balls, the Racing 5 is cartridge. Link below:
https://cyclingtips.com/2018/05/fulc...eelset-review/
Edit: Corrected myself - DaveSSS had it right, it's the Racing 3 and Racing 0 that have balls, the Racing 5 is cartridge. Link below:
https://cyclingtips.com/2018/05/fulc...eelset-review/
Last edited by aliasfox; 07-01-21 at 03:51 PM.
#12
Senior Member
Join Date: Apr 2021
Posts: 4,083
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 2333 Post(s)
Liked 2,097 Times
in
1,314 Posts
Only Campy and Shimano do cup and cone.
Cup and cone are less efficient, so, there you go.
Cup and cone are less efficient, so, there you go.
#13
Senior Member
Join Date: Dec 2009
Location: Melbourne, Oz
Posts: 9,547
Bikes: https://weightweenies.starbike.com/forum/viewtopic.php?f=10&t=152015&p=1404231
Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
Quoted: 1529 Post(s)
Liked 718 Times
in
510 Posts
Lolwut. Vast majority of bearing drag is in the seals, and sealing of cartridge bearings is often sub par. Also, I've almost never seen a cartridge hub with preload adjustment, so no preload is probably a tiny bit less drag.
Give me sealing and preload any day, adjust them properly and never revisit them.
Factor in throwing away your bearings every time they get contaminated, probably not so efficient in the big picture.
Also, hub bearing drag is a trivial factor, given the tyre's leverage over the bearings.
Give me sealing and preload any day, adjust them properly and never revisit them.
Factor in throwing away your bearings every time they get contaminated, probably not so efficient in the big picture.
Also, hub bearing drag is a trivial factor, given the tyre's leverage over the bearings.
#14
working on my sandal tan
Join Date: Aug 2011
Location: CID
Posts: 22,629
Bikes: 1991 Bianchi Eros, 1964 Armstrong, 1988 Diamondback Ascent, 1988 Bianchi Premio, 1987 Bianchi Sport SX, 1980s Raleigh mixte (hers), All-City Space Horse (hers)
Mentioned: 98 Post(s)
Tagged: 0 Thread(s)
Quoted: 3871 Post(s)
Liked 2,568 Times
in
1,579 Posts
That's what I do. Since Shimano hubs are so long-lasting, you don't even have to buy new.
#15
Senior Member
Join Date: Dec 2009
Location: Melbourne, Oz
Posts: 9,547
Bikes: https://weightweenies.starbike.com/forum/viewtopic.php?f=10&t=152015&p=1404231
Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
Quoted: 1529 Post(s)
Liked 718 Times
in
510 Posts
I reckon we've established that 32 spokes is more than you need, unless you've got some super light box section rims maybe.
If you wanna use poxy old J-bend flanges, you can lace em up 16/24, with the rear either standard or triplet.
If you wanna use poxy old J-bend flanges, you can lace em up 16/24, with the rear either standard or triplet.
#16
Senior Member
Join Date: Apr 2021
Posts: 4,083
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 2333 Post(s)
Liked 2,097 Times
in
1,314 Posts
Lolwut. Vast majority of bearing drag is in the seals, and sealing of cartridge bearings is often sub par. Also, I've almost never seen a cartridge hub with preload adjustment, so no preload is probably a tiny bit less drag.
Give me sealing and preload any day, adjust them properly and never revisit them.
Factor in throwing away your bearings every time they get contaminated, probably not so efficient in the big picture.
Also, hub bearing drag is a trivial factor, given the tyre's leverage over the bearings.
Give me sealing and preload any day, adjust them properly and never revisit them.
Factor in throwing away your bearings every time they get contaminated, probably not so efficient in the big picture.
Also, hub bearing drag is a trivial factor, given the tyre's leverage over the bearings.
I use NTN bearings and they will probably outlast me. They never get contaminated, what are you talking about. Big picture nonsense.
#17
Senior Member
Join Date: Dec 2009
Location: Melbourne, Oz
Posts: 9,547
Bikes: https://weightweenies.starbike.com/forum/viewtopic.php?f=10&t=152015&p=1404231
Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
Quoted: 1529 Post(s)
Liked 718 Times
in
510 Posts
Hambini has proven the Shimano cup and cone bearings have more drag. Say 5 watts vs 2 watts. Might be trivial to you. Who is generating your wheel leverage, LOL. I have owned plenty of campy and shimano hubs. They have never been set it and forget it.
I use NTN bearings and they will probably outlast me. They never get contaminated, what are you talking about. Big picture nonsense.
I use NTN bearings and they will probably outlast me. They never get contaminated, what are you talking about. Big picture nonsense.
#18
Senior Member
Join Date: Nov 2014
Location: Eugene, Oregon, USA
Posts: 27,547
Mentioned: 217 Post(s)
Tagged: 0 Thread(s)
Quoted: 18378 Post(s)
Liked 4,512 Times
in
3,354 Posts
For those that know how to do it, they're easy and cheap to rebuild and can last a long time.
I've got cartridge bearings in a Campy crank that got wet and all crunchy. I now have to figure out how to disassemble and clean the thing, then relube, reassemble, and hope for the best...
One thing that would be nice would be a longterm commitment for spare parts.
There is someone that is looking for Ultegra 6700 cones... almost impossible to find now, although it is not clear if it is just not available, or poor parts distribution.
And, of course the 6800 and 8000 cones are different.
I've got cartridge bearings in a Campy crank that got wet and all crunchy. I now have to figure out how to disassemble and clean the thing, then relube, reassemble, and hope for the best...
One thing that would be nice would be a longterm commitment for spare parts.
There is someone that is looking for Ultegra 6700 cones... almost impossible to find now, although it is not clear if it is just not available, or poor parts distribution.
And, of course the 6800 and 8000 cones are different.
#19
Senior Member
Join Date: Dec 2009
Location: Melbourne, Oz
Posts: 9,547
Bikes: https://weightweenies.starbike.com/forum/viewtopic.php?f=10&t=152015&p=1404231
Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
Quoted: 1529 Post(s)
Liked 718 Times
in
510 Posts
One thing that would be nice would be a longterm commitment for spare parts.
There is someone that is looking for Ultegra 6700 cones... almost impossible to find now, although it is not clear if it is just not available, or poor parts distribution.
And, of course the 6800 and 8000 cones are different.
There is someone that is looking for Ultegra 6700 cones... almost impossible to find now, although it is not clear if it is just not available, or poor parts distribution.
And, of course the 6800 and 8000 cones are different.
What really burns me up is that they don't even pretend to supply replacements for their fabulous RS80/81/Dura-Ace carbon/ally rims, which being rim brake, are unquestionably consumables. God damn.
#20
Senior Member
Join Date: Nov 2014
Location: Eugene, Oregon, USA
Posts: 27,547
Mentioned: 217 Post(s)
Tagged: 0 Thread(s)
Quoted: 18378 Post(s)
Liked 4,512 Times
in
3,354 Posts
I think part of the bike company's problems are a difficulty adapting to an online marketing. It is not any one company, but all of them from frame builders to component vendors.
Something like spare parts would naturally fit into an online support model.
Bike shops might not like to stock all the spare parts to support 70 year old components. But it would be easy enough for a central vendor to stock and distribute the parts. Then every year or so put in an order of 1000 or so "genuine" Nuovo Record cones.
Or have derailleur hangers in stock ready to ship.
It is interesting that companies like Wheels Manufacturing can make a business of cloning cones, derailleur hangers, etc that the OEM companies refuse to support.
Something like spare parts would naturally fit into an online support model.
Bike shops might not like to stock all the spare parts to support 70 year old components. But it would be easy enough for a central vendor to stock and distribute the parts. Then every year or so put in an order of 1000 or so "genuine" Nuovo Record cones.
Or have derailleur hangers in stock ready to ship.
It is interesting that companies like Wheels Manufacturing can make a business of cloning cones, derailleur hangers, etc that the OEM companies refuse to support.
Likes For CliffordK:
#21
Senior Member
My main gripe with modern hubs is the idiotic rear wheel design, with the right hand bearing at or even behind the spoke flange. Its worse than old school screw on freewheels. Sadly even Shimano, Microspline does this now. I agree that classic shimano cup and cone hubs with a steel free hub body is still the best available. Id pick that for a wheel build.