Carbon Seat Rails.
#26
Senior Member
Join Date: Sep 2017
Posts: 8,038
Mentioned: 42 Post(s)
Tagged: 0 Thread(s)
Quoted: 7084 Post(s)
Liked 11,189 Times
in
4,782 Posts
btw, 2-3nm seems like a very low torque for a saddle clamp; is that Bontrager's spec?
#27
Junior Member
Obviously not relevant to the thread's original post, since it describes something that obviously did not happen with your saddle; in fact, I can't really see any failure in the photo. Am I missing something? I feel like there must be a crack somewhere that I'm not seeing.
btw, 2-3nm seems like a very low torque for a saddle clamp; is that Bontrager's spec?
btw, 2-3nm seems like a very low torque for a saddle clamp; is that Bontrager's spec?
I read in the instructions to tighten to 4 nm but what ‘felt’ right to me was 2-3 nm. I’m patiently waiting for the cracks to form and the saddle to fall off.
#28
Senior Member
Join Date: Sep 2017
Posts: 8,038
Mentioned: 42 Post(s)
Tagged: 0 Thread(s)
Quoted: 7084 Post(s)
Liked 11,189 Times
in
4,782 Posts
It sounds like you are accusing me of being incapable of breaking something. Well, guilty as charged, but I do have great aspirations.
I read in the instructions to tighten to 4 nm but what ‘felt’ right to me was 2-3 nm. I’m patiently waiting for the cracks to form and the saddle to fall off.
I read in the instructions to tighten to 4 nm but what ‘felt’ right to me was 2-3 nm. I’m patiently waiting for the cracks to form and the saddle to fall off.
I would torque it to spec, especially since even 4nm isn't much. But you're probably fine.
#29
Clark W. Griswold
Join Date: Mar 2014
Location: ,location, location
Posts: 13,780
Bikes: Foundry Chilkoot Ti W/Ultegra Di2, Salsa Timberjack Ti, Cinelli Mash Work RandoCross Fun Time Machine, 1x9 XT Parts Hybrid, Co-Motion Cascadia, Specialized Langster, Phil Wood Apple VeloXS Frame (w/DA 7400), R+M Supercharger2 Rohloff, Habanero Ti 26
Mentioned: 55 Post(s)
Tagged: 0 Thread(s)
Quoted: 4448 Post(s)
Liked 4,109 Times
in
2,743 Posts
My carbon railed C13 (technically a 17 in width) has supported my more ample rear for many years and is still going strong. It is installed on a Ritchey Classic post and was done properly with a torque wrench. I do occasionally worry about it and would prefer it to be titanium but it was carbon and works fine. So long as you have the correct clamping mechanism for the saddle (check with the manufacturer) and you torque it all properly and don't ride like a maniac you will be fine.
Carbon is quite a strong resilient material. If it wasn't they wouldn't be using it in all the various critical applications they use it in. I know it is easy to hate on carbon certainly it can fail terribly but so can many materials if treated poorly in some way or another.
Carbon is quite a strong resilient material. If it wasn't they wouldn't be using it in all the various critical applications they use it in. I know it is easy to hate on carbon certainly it can fail terribly but so can many materials if treated poorly in some way or another.
#30
Senior Member
Join Date: Jul 2009
Posts: 6,038
Bikes: Colnago, Van Dessel, Factor, Cervelo, Ritchey
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 3998 Post(s)
Liked 7,489 Times
in
3,013 Posts
#31
climber has-been
Join Date: Dec 2004
Location: Palo Alto, CA
Posts: 7,236
Bikes: Scott Addict R1, Felt Z1
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 3538 Post(s)
Liked 3,691 Times
in
1,850 Posts
The left clamp is what I was asking about in my earlier post. The clamp edge being into the start of the turn of the rails. CF doesn't "flow" at all so the concentrated force at that clamp edge will never dissipate. I asked the OP if this was the case so we could all learn but I suspect the hostile replies drove him off.
#32
Clark W. Griswold
Join Date: Mar 2014
Location: ,location, location
Posts: 13,780
Bikes: Foundry Chilkoot Ti W/Ultegra Di2, Salsa Timberjack Ti, Cinelli Mash Work RandoCross Fun Time Machine, 1x9 XT Parts Hybrid, Co-Motion Cascadia, Specialized Langster, Phil Wood Apple VeloXS Frame (w/DA 7400), R+M Supercharger2 Rohloff, Habanero Ti 26
Mentioned: 55 Post(s)
Tagged: 0 Thread(s)
Quoted: 4448 Post(s)
Liked 4,109 Times
in
2,743 Posts
No it is the designation from Brooks, they have the C13, C15, C17 and C19. If my rear was that big I would have problems and I doubt I could use a carbon railed saddle or probably most any saddle at that point.