197* Harding? Holdsworth rebrand? Any thoughts?
#1
Member
Thread Starter
Join Date: Sep 2011
Posts: 29
Likes: 0
Liked 0 Times
in
0 Posts
197* Harding? Holdsworth rebrand? Any thoughts?
So I bit off way more than I could chew and attempted to buy a project bike as my first post-middle-school bike... too much.
It's an unknown year, branded as a Harding. The bike rides fine but there's rust in a few problematic areas- namely the spokes and rear brake cable guide. But overall, it's a pretty *****in bike. Reynolds 531, SunTour AR and ARX deraileurs, GB bars that show really well
I'm not going to try to pitch the bike, but I'm near LA and bikes are awful tough to come by around here. It seems like every time I try to snap up a good one it's gone in 2 hours.
Anyway, here's a pic, I look forward to hearing your thoughts. Any more info that would be useful? Any ideas on value-adds?
It's an unknown year, branded as a Harding. The bike rides fine but there's rust in a few problematic areas- namely the spokes and rear brake cable guide. But overall, it's a pretty *****in bike. Reynolds 531, SunTour AR and ARX deraileurs, GB bars that show really well
I'm not going to try to pitch the bike, but I'm near LA and bikes are awful tough to come by around here. It seems like every time I try to snap up a good one it's gone in 2 hours.
Anyway, here's a pic, I look forward to hearing your thoughts. Any more info that would be useful? Any ideas on value-adds?
#2
Senior Member
I was expecting to see an orange one. Harding was a private brand of Charlie Harding's Westwood Cyclery in LA.
The orange ones were made by Holdsworth, from 1974-75. It took a while for him to sell them off, so some were new but later.
I have never seen one of these. Small possibility that another Harding family member in Ireland had a hand in it.
Charlie also sold Falcon, so that is a possibility too as the builder.
The orange ones were made by Holdsworth, from 1974-75. It took a while for him to sell them off, so some were new but later.
I have never seen one of these. Small possibility that another Harding family member in Ireland had a hand in it.
Charlie also sold Falcon, so that is a possibility too as the builder.
#3
Senior Member
Join Date: Sep 2010
Location: NE Indiana
Posts: 8,742
Bikes: 2020 Masi Giramondo 700c; 2013 Lynskey Peloton; 1992 Giant Rincon; 1989 Dawes needs parts; 1985 Trek 660; 1985 Fuji Club; 1984 Schwinn Voyager; 1984 Miyata 612; 1977 Raleigh Competition GS
Liked 277 Times
in
224 Posts
I would keep the bike and do some extensive research on it and become an expert on it because not much is known about these.
Your bike may turn out to be quite rare if Charlie Harding built it. Harding did build some of own, while others he had shipped frame and fork from England, those may have been the orange ones made by Holdsworth, since yours is not orange it could be very rare frame and fork actually built by Harding. Holdsworth also used a wrap over seat stay that wrapped over the seat tube at the top, it it's a Holdsworth of a different color that would be a big give away. See this for what I mean, this is a Harding Holdsworth by the way: https://www.flickr.com/photos/alexjri...n/photostream/
Either way, if Harding built it himself it would be a very rare bike since he made very few and built them mostly for himself but did sell a few; or if the bike is a Harding Holdsworth it's still a rare bike since very few of those examples are still around today. There is another twist to this story. C. Harding had family in Cork Ireland who built bicycles for Harding! But that story takes on another twist of it's own because back then in Cork Ireland Raleigh had a factory there till it burned down...so did Harding's family own or run that factory or have their own separate small factory? or did Harding tell a story and was actually selling rebranded Raleighs with his name on it? that is what most people think what happened.
By the way his shop's name was: C Hardings for Bikes, it was located in Los Angeles. I believe he may have moved back to Cork Ireland because there is a shop in Cork named Harding Cycles there, the address is 19 Rutland Street, Cork Ireland. phone number is 02143211133 I have not tried to contact this info so I cannot guarantee if the info is still any good. And being that Charlie was born in the 20's there's a good chance he's dead, but maybe not, either way the family may still be operating thus they could provide you a wealth of info.
Please post pictures, not here so much but on the internet so others can readily see the bike, because all I could find was the orange Harding, thus others would be very interested in seeing pictures.
Your bike may turn out to be quite rare if Charlie Harding built it. Harding did build some of own, while others he had shipped frame and fork from England, those may have been the orange ones made by Holdsworth, since yours is not orange it could be very rare frame and fork actually built by Harding. Holdsworth also used a wrap over seat stay that wrapped over the seat tube at the top, it it's a Holdsworth of a different color that would be a big give away. See this for what I mean, this is a Harding Holdsworth by the way: https://www.flickr.com/photos/alexjri...n/photostream/
Either way, if Harding built it himself it would be a very rare bike since he made very few and built them mostly for himself but did sell a few; or if the bike is a Harding Holdsworth it's still a rare bike since very few of those examples are still around today. There is another twist to this story. C. Harding had family in Cork Ireland who built bicycles for Harding! But that story takes on another twist of it's own because back then in Cork Ireland Raleigh had a factory there till it burned down...so did Harding's family own or run that factory or have their own separate small factory? or did Harding tell a story and was actually selling rebranded Raleighs with his name on it? that is what most people think what happened.
By the way his shop's name was: C Hardings for Bikes, it was located in Los Angeles. I believe he may have moved back to Cork Ireland because there is a shop in Cork named Harding Cycles there, the address is 19 Rutland Street, Cork Ireland. phone number is 02143211133 I have not tried to contact this info so I cannot guarantee if the info is still any good. And being that Charlie was born in the 20's there's a good chance he's dead, but maybe not, either way the family may still be operating thus they could provide you a wealth of info.
Please post pictures, not here so much but on the internet so others can readily see the bike, because all I could find was the orange Harding, thus others would be very interested in seeing pictures.
Last edited by rekmeyata; 11-20-11 at 12:25 AM.
#4
Senior Member
Join Date: Apr 2007
Location: Thunder Bay, Ontario, Canada - burrrrr!
Posts: 11,940
Bikes: 1958 Rabeneick 120D, 1968 Legnano Gran Premio, 196? Torpado Professional, 2000 Marinoni Piuma
Likes: 0
Liked 2,017 Times
in
1,065 Posts
I can't offer much information pertaining to the Harding brand, but I can help a bit with identifying vintage. Apply some of the information offered in How Old Is My Bike?, paying closest attention to Component Numbers. That should get you pretty close to determining how old the bike is.
As for Determining Bicycle Value, that is a whole different ball game and, generally, it is pretty difficult to predict how much a vintage bicycle is worth. Many things impact value, including location, time of year, size of bike and things like that.
Hope this is a bit of help and nice bike, by the way. I have had a few similar ones, including one still hanging in The Old Shed.
As for Determining Bicycle Value, that is a whole different ball game and, generally, it is pretty difficult to predict how much a vintage bicycle is worth. Many things impact value, including location, time of year, size of bike and things like that.
Hope this is a bit of help and nice bike, by the way. I have had a few similar ones, including one still hanging in The Old Shed.
__________________
"98% of the bikes I buy are projects".
"98% of the bikes I buy are projects".
#5
Senior Member
Assuming the derailleurs arer original would place it no older than a 1981 model.
#6
Constant tinkerer
My question is what are suicide levers, Suntour AR, and a cheapo seatpost doing on a (possibly handbuilt) 531 frame? I can't believe all that stuff is original.
What's the wheelset?
What's the wheelset?
#7
Member
Thread Starter
Join Date: Sep 2011
Posts: 29
Likes: 0
Liked 0 Times
in
0 Posts
The seat post is definitely not original- it has a Kmart seat on it at the moment, as found. I have some more shots that I will upload when I get home that will show the details
The wheels are 27" and any stickers that may have been on the rims are gone except one blue one that says 'competition.' Normandy hubs. The spokes are pretty severely rusted at this point
The wheels are 27" and any stickers that may have been on the rims are gone except one blue one that says 'competition.' Normandy hubs. The spokes are pretty severely rusted at this point
#9
Senior Member
Join Date: Sep 2010
Location: NE Indiana
Posts: 8,742
Bikes: 2020 Masi Giramondo 700c; 2013 Lynskey Peloton; 1992 Giant Rincon; 1989 Dawes needs parts; 1985 Trek 660; 1985 Fuji Club; 1984 Schwinn Voyager; 1984 Miyata 612; 1977 Raleigh Competition GS
Liked 277 Times
in
224 Posts
Suntour AR was a mid level derailleur in the Suntour line up, the ARX was above it followed by the Blue Line right below it. They were actually a very good derailleur, though I don't think that the AR was the original either on that bike, but could be wrong. It was still a better shifting derailleur then most of Shimano or Campy stuff!! But I would think that Harding would have spec'd a racing bike with a higher grade of components then that.
Again this is why you need to do some extensive research and contact as many people as you can, especially the contact info I gave you, and try to find out what the original components may have been. Due to the rarity of the bike I would personally attempt to restore it back to original specs and not bastardize into something else. Keep in mind that I own several vintage cars and my thought pattern is always about maintaining originality as much as humanly possible. And sometimes in that pursuit of originality it could take many months of research to acquire a certain part, and the part may be expensive. But for bike parts on that bike it shouldn't be rare or expensive to buy the parts, your difficulty is going to be finding out what parts went on it.
#10
Thrifty Bill
Join Date: Jan 2008
Location: Mountains of Western NC
Posts: 23,557
Bikes: 86 Katakura Silk, 87 Prologue X2, 88 Cimarron LE, 1975 Sekai 4000 Professional, 73 Paramount, plus more
Liked 1,008 Times
in
649 Posts
+10 No way those parts were original on that bike. I typically find AR bits on high ten steel bikes, or at best, bikes with generic cromoly main frames with the rest high ten. The 531 framesets I find with Suntour components tend to have parts that are higher up the product line. Nothing wrong with AR bits, I just tend to find them on lower end, recreational bikes.
#11
Senior Member
Join Date: Sep 2010
Location: NE Indiana
Posts: 8,742
Bikes: 2020 Masi Giramondo 700c; 2013 Lynskey Peloton; 1992 Giant Rincon; 1989 Dawes needs parts; 1985 Trek 660; 1985 Fuji Club; 1984 Schwinn Voyager; 1984 Miyata 612; 1977 Raleigh Competition GS
Liked 277 Times
in
224 Posts
+10 No way those parts were original on that bike. I typically find AR bits on high ten steel bikes, or at best, bikes with generic cromoly main frames with the rest high ten. The 531 framesets I find with Suntour components tend to have parts that are higher up the product line. Nothing wrong with AR bits, I just tend to find them on lower end, recreational bikes.
The order of 1981 Suntour components when AR was introduced was from top to bottom: Superbe Pro, Superbe, Cyclone Mk II, Cyclone, BL, ARx, Vx, AR, Seven, Volante, Honor, GT, and Mighty Click. There is a controversy about the mid order between the BL, ARx, Vx and AR, a lot of people rated the BL below the AR due to it's weight and finish quality. And the ARx was an attempt at being aero but had problems with shifting as well as the others in the mid lineup so some placed that one below Vx but above BL if BL was below AR. Confused now?
#12
Member
Thread Starter
Join Date: Sep 2011
Posts: 29
Likes: 0
Liked 0 Times
in
0 Posts
OK guys, get ready for some visual stimulus... Please, please forgive the oversharpened photos my iPhone took! I would go back and take new ones but they get the point across and it's 12:30 on a school night
The headset is Campy, dropouts are Campy, every Harding I've found mentioned on this board for the last 5 years has been heavy on Campy, usually NR... As you can see from the pics, she's been pretty neglected for the past who knows how many years
The headset is Campy, dropouts are Campy, every Harding I've found mentioned on this board for the last 5 years has been heavy on Campy, usually NR... As you can see from the pics, she's been pretty neglected for the past who knows how many years
Last edited by Displacement; 11-21-11 at 02:38 AM.
#14
Senior Member
#15
Senior Member
As this is most likely an Irish Harding, your inquiries should go there. Anyone else's guess as if it was imported by Charlie or by an owner.
The oddball component group could well be original, Ireland had to import everything, so as they were not in the EU at the time, parts could come from anywhere.
The oddball component group could well be original, Ireland had to import everything, so as they were not in the EU at the time, parts could come from anywhere.
#16
Senior Member
Join Date: Sep 2010
Location: NE Indiana
Posts: 8,742
Bikes: 2020 Masi Giramondo 700c; 2013 Lynskey Peloton; 1992 Giant Rincon; 1989 Dawes needs parts; 1985 Trek 660; 1985 Fuji Club; 1984 Schwinn Voyager; 1984 Miyata 612; 1977 Raleigh Competition GS
Liked 277 Times
in
224 Posts
Nice lug work, but having seen the lugs I'm questioning the Holdsworth connection now. I don't recall ever seeing a Holdsworth with those kind of lugs, nor the seat stay spoons, typical Holdsworth spoons wrapped around the entire seat tube and they used short pointed lugs without the ornate style; but I haven't seen a lot of Holdsworth's so I could be wrong. I'm leaning toward either a Raleigh who did use lugs that looked like that on occasion especially the early Professional's, and Raleigh did have a factory in Cork; or it could indeed be a custom built frame built by his family in Cork.
#18
Member
Thread Starter
Join Date: Sep 2011
Posts: 29
Likes: 0
Liked 0 Times
in
0 Posts
Nice lug work, but having seen the lugs I'm questioning the Holdsworth connection now. I don't recall ever seeing a Holdsworth with those kind of lugs, nor the seat stay spoons, typical Holdsworth spoons wrapped around the entire seat tube and they used short pointed lugs without the ornate style; but I haven't seen a lot of Holdsworth's so I could be wrong. I'm leaning toward either a Raleigh who did use lugs that looked like that on occasion especially the early Professional's, and Raleigh did have a factory in Cork; or it could indeed be a custom built frame built by his family in Cork.
#19
Senior Member
Join Date: Sep 2010
Location: NE Indiana
Posts: 8,742
Bikes: 2020 Masi Giramondo 700c; 2013 Lynskey Peloton; 1992 Giant Rincon; 1989 Dawes needs parts; 1985 Trek 660; 1985 Fuji Club; 1984 Schwinn Voyager; 1984 Miyata 612; 1977 Raleigh Competition GS
Liked 277 Times
in
224 Posts
Again the op needs to contact people and have the serial number handy because it may help figure out where the bike came from.
#20
Member
Thread Starter
Join Date: Sep 2011
Posts: 29
Likes: 0
Liked 0 Times
in
0 Posts
Sorry, didn't mean to sound hostile, just made sense to me that it was sold in Westwood if it wound up in somebody's garage 15 miles away 30 something years later. I posted the serial number in one of the photos, thought it might be helpful - it's 069236. I assumed it was a factory built frame sold here, I had hoped to get better information about which factory. I don't understand if you guys are suggesting this was something sold through Harding's Westwood shop or something sold later, through that Harding Bicycles that's opened up across the pond, then was later imported
Any ideas on value, assuming the worst? I really don't mind what the vintage is, it's still a very nice riding bike and pretty light. Just looking for some information so I'm an informed seller
Any ideas on value, assuming the worst? I really don't mind what the vintage is, it's still a very nice riding bike and pretty light. Just looking for some information so I'm an informed seller
#21
Senior Member
Was it sold through his shop? Maybe, one interesting feature that this bike does not have is the typical sold by C. Harding's Westwood Cyclery transfer which he placed on all bikes I remember seeing at his shop.
#22
Senior Member
Sorry, didn't mean to sound hostile, just made sense to me that it was sold in Westwood if it wound up in somebody's garage 15 miles away 30 something years later. I posted the serial number in one of the photos, thought it might be helpful - it's 069236. No idea what that means though.
Any ideas on value, assuming the worst? I really don't mind what the vintage is, it's still a very nice riding bike and pretty light. Just looking for some information so I'm an informed seller
Any ideas on value, assuming the worst? I really don't mind what the vintage is, it's still a very nice riding bike and pretty light. Just looking for some information so I'm an informed seller
#23
Full Member
Join Date: Nov 2012
Location: High Desert above L.A.
Posts: 294
Bikes: Primary bike - late 70's gold ALAN Competition; mostly Campy with Huret Jubilee deraiileurs. Now back to my 1979/80 Shogun 600 since I can change everything and not feel like I'm committing sacrilege... but building up the Hetchins
Liked 407 Times
in
169 Posts
Not sure if this thread still has any relevance but Charlie is still alive and well. His family did and does have shops in Ireland. He was the owner during my time and may still be. He splits time there and here although the Westwood store is long closed. His brother (George I believe) made bikes but they did also sell rebranded Holdsworth's. I'll have to ask Charlie when I see him whether he ever made any of his own that ended up in shops. By the time I worked for him (and there was always at least one employee, part of my time we had 3!) he was spending about half his time in Ireland and managed the businesses - the Westwood shop, a shop in Cork and one in Dublin. There is more to the factory story but that is his story to tell not mine. His shop in Westwood didn't close until sometime around or after '87 - about the time he was down to no employees I may have been his last.
When he had the C.Harding logo on his own bike he didn't always (I'll never say never) also place our Westwood shop stamp on the bike. We also would sell framesets by themselves so this frameset could have been sold, as many of our frames were, to an enthusiast that built it up himself or ordered parts as opposed to purchasing a completed bike.
My two cents worth.
When he had the C.Harding logo on his own bike he didn't always (I'll never say never) also place our Westwood shop stamp on the bike. We also would sell framesets by themselves so this frameset could have been sold, as many of our frames were, to an enthusiast that built it up himself or ordered parts as opposed to purchasing a completed bike.
My two cents worth.
#24
Full Member
Join Date: Nov 2012
Location: High Desert above L.A.
Posts: 294
Bikes: Primary bike - late 70's gold ALAN Competition; mostly Campy with Huret Jubilee deraiileurs. Now back to my 1979/80 Shogun 600 since I can change everything and not feel like I'm committing sacrilege... but building up the Hetchins
Liked 407 Times
in
169 Posts
I got sent a private message re Harding's bikes but since I have posted too little, I don't have access to respond privately so I'll post question and my response in this public thread:
"I am trying to decipher the Holdsworth serial numbers from the early 70's of frames that were rebranded by Harding. Would you know if these frames would have given a number by Charlie or were they "Holdsworth" numbers?"
First: this message is dated January of 2017 and I happened to visit Charlie today so I did enquire. Although there were actual "made by Harding" bikes, those were almost all made and sold in the Irish shops. 10 or so were sold out of the Westwood shop.
The Holdsworth Hardings were not simply rebranded Holdsworth, they were Harding's specs licensed to Holdsworth - so different designs from other Holdsworth production lines.
The serial numbers on the Holdsworth production line had their numbers go on in production from Holdsworth and Charlie simply doesn't recall whether he or his brother had Holdsworth create a separate or different serial number series, stream or sequence from Holdsworth's other production lines. Sorry Doug that I couldn't get any better info for you.
"I am trying to decipher the Holdsworth serial numbers from the early 70's of frames that were rebranded by Harding. Would you know if these frames would have given a number by Charlie or were they "Holdsworth" numbers?"
First: this message is dated January of 2017 and I happened to visit Charlie today so I did enquire. Although there were actual "made by Harding" bikes, those were almost all made and sold in the Irish shops. 10 or so were sold out of the Westwood shop.
The Holdsworth Hardings were not simply rebranded Holdsworth, they were Harding's specs licensed to Holdsworth - so different designs from other Holdsworth production lines.
The serial numbers on the Holdsworth production line had their numbers go on in production from Holdsworth and Charlie simply doesn't recall whether he or his brother had Holdsworth create a separate or different serial number series, stream or sequence from Holdsworth's other production lines. Sorry Doug that I couldn't get any better info for you.
#25
Full Member
Join Date: Nov 2012
Location: High Desert above L.A.
Posts: 294
Bikes: Primary bike - late 70's gold ALAN Competition; mostly Campy with Huret Jubilee deraiileurs. Now back to my 1979/80 Shogun 600 since I can change everything and not feel like I'm committing sacrilege... but building up the Hetchins
Liked 407 Times
in
169 Posts
For those of you who remember C.Harding's Westwood Cyclery, Charlie himself or the old crowd like Hans Ort etc, a couple corrections and sad news. I read someone here mention that C. Harding's became or was replaced by Helen's. Helen's was a late 70's Schwinn shop on Santa Monica Blvd. that grew - wonderfully. I used to work with some of the people who ended up there. They opened a second shop IN Westwood. Charlie was south of Wilshire -never the twain shall have met. He simply closed because the crew of worker's aged out - David, John, Doug/Dudla, myself... we ran out of younger riders-friends to bring in to replace us and Charlie finally had family and Ireland to enjoy. Well, Charlie passed away December 13, 2023 and has returned to Ireland. He was a brilliant mechanic, knowledgeable beyond what I could learn while with him, and a pleasure to work with while still being at times an irascible Irish curmudgeon. He had his own opinions about many things, including "innovation" - like every time oblong chain rings "cycled" around under a new name - Bio Pace just one of many versions he appreciated for the thought but not the marketability; and about who was really profiting by all the advancements that wall us into new systems and lend to quick obsolescence ... draw ratios never matter to a friction shifter! Yes, new technology is amazing - but at the same time, the simplicity of friction shifting, cones, cups, bearings, and a tube of grease make for a cheap and easy time for a weekend warrior mechanic. I will miss him dearly. you can find his obit in Cork by googling his name Charles Albert Harding and Cork...