V brake levers ?
#1
Senior Member
Thread Starter
V brake levers ?
Can i use the Shimano EZFire brake/shifter made for V brakes for cantilevers ?
#2
Senior Member
Join Date: Sep 2010
Location: Roswell, GA
Posts: 8,321
Bikes: '93 Trek 750, '92 Schwinn Crisscross, '93 Mongoose Alta
Liked 1,095 Times
in
725 Posts
V-brake levers have what is referred to as "long pull" characteristics, they pull a relatively large amount of cable with lower leverage; cantilever and caliper brakes use "short pull", they pull less cable so have higher leverage. V-brake levers would likely lack the leverage needed for good power in a cantilever system.
#3
Senior Member
Thread Starter
I understand....trying to find a good brake/shift combo to replace the cheaper ones i have
This is the model
This outer housing is broken ...sont know if i can get just the shift mechanism
This is the model
This outer housing is broken ...sont know if i can get just the shift mechanism
Last edited by Night Treker; 07-18-20 at 03:17 PM.
#5
SE Wis
Join Date: Apr 2005
Location: Milwaukee, WI
Posts: 10,572
Bikes: '68 Raleigh Sprite, '02 Raleigh C500, '84 Raleigh Gran Prix, '91 Trek 400, 2013 Novara Randonee, 1990 Trek 970
Liked 3,428 Times
in
2,076 Posts
YOu should be able to pull the existing shifter pod off the brake lever and pick up a shifter that uses a separate mount and keep your brake lever.
#6
Really Old Senior Member
IF you can find these in the 4 Finger Version-
You have to pay attention, because most are "2 finger" and NOT convertible between V & Canti.
You have to pay attention, because most are "2 finger" and NOT convertible between V & Canti.
Likes For Bill Kapaun:
#7
Senior Member
Join Date: Jun 2014
Location: Ontario, Canada
Posts: 4,624
Bikes: iele Latina, Miele Suprema, Miele Uno LS, Miele Miele Beta, MMTB, Bianchi Model Unknown, Fiori Venezia, Fiori Napoli, VeloSport Adamas AX
Liked 929 Times
in
642 Posts
From Sheldon Brown (about 3/4 down the page) https://www.sheldonbrown.com/canti-direct.html
"
Brake Levers for Direct-pull Cantilevers
Direct-pull cantilevers have double the mechanical advantage compared with traditional brakes, so they require special brake levers. Direct-pull brake levers pull the cable twice as far, half as hard. The lower mechanical advantage of the lever compensates for the higher mechanical advantage of the brake arms. It is not generally safe to mix and match levers/cables between direct-pull and other types for this reason.- Conventional brake levers used with direct-pull cantilevers will usually not pull enough cable to stop in wet conditions without bottoming out against the handlebars. In dry conditions, they either won't work, or will grab too suddenly."
#8
Senior Member
Thread Starter
The reason is these bars have a very long rubber grip that i might not be able to remove easily
havent found any NOS either
havent found any NOS either
#9
SE Wis
Join Date: Apr 2005
Location: Milwaukee, WI
Posts: 10,572
Bikes: '68 Raleigh Sprite, '02 Raleigh C500, '84 Raleigh Gran Prix, '91 Trek 400, 2013 Novara Randonee, 1990 Trek 970
Liked 3,428 Times
in
2,076 Posts
If you have a co-op nearby you may want to start checking with them for a used set. If they're open given COVID.
The shifter can be separated from the brake lever.
https://si.shimano.com/pdfs/ev/EV-ST-M290-1453A.pdf
The shifter can be separated from the brake lever.
https://si.shimano.com/pdfs/ev/EV-ST-M290-1453A.pdf
#10
Banned
Some levers have 2 places to fit the cable head further or nearer the lever pivot, in set up, .. Avid speed dial it's an adjustment..
I have Speed Dial levers ... The rear an Avid MTB, front a TRP Hy Rd same lever on both adjusted for best feel..
...
I have Speed Dial levers ... The rear an Avid MTB, front a TRP Hy Rd same lever on both adjusted for best feel..
...
Last edited by fietsbob; 07-18-20 at 10:26 PM.
#11
Senior Member
Join Date: Feb 2004
Location: St Peters, Missouri
Posts: 30,225
Bikes: Catrike 559 I own some others but they don't get ridden very much.
Liked 644 Times
in
365 Posts
My personal philosophy is that if I'm buying parts I'll only pay for stuff that's supposed to work together. If I already own parts, I'll bolt up whatever I have and see if I can make it work to my satisfaction.
I've done it, I thought it felt okay, and I don't have unusual grip strength. It's one of those things that I might do on a personal bike but I wouldn't do on a customer bike.
I've done it, I thought it felt okay, and I don't have unusual grip strength. It's one of those things that I might do on a personal bike but I wouldn't do on a customer bike.
__________________
My greatest fear is all of my kids standing around my coffin and talking about "how sensible" dad was.
My greatest fear is all of my kids standing around my coffin and talking about "how sensible" dad was.
#14
Senior Member
Slide a long thin screwdriver down inside them, work it around a bit, squirt in some soapy water, start twisting. Another option, if you have access to a compressor and the grips have end holes, hold one grip on, blow air in the other one and blow it off.
#15
Senior Member
Join Date: Feb 2004
Location: St Peters, Missouri
Posts: 30,225
Bikes: Catrike 559 I own some others but they don't get ridden very much.
Liked 644 Times
in
365 Posts
I've always kept a spray bottle of Windex on my workbench. Removing and installing hand grips is one of the purposes that I use it for. Those long rubber grips on nightstalker's bike might be troublesome. If it was my bike I'd spray a little Windex under the grip, see how much of the grip I could get to wiggle and try it again. If it works, (and I'm betting it will eventually) it's probably going to take several attempts..
__________________
My greatest fear is all of my kids standing around my coffin and talking about "how sensible" dad was.
My greatest fear is all of my kids standing around my coffin and talking about "how sensible" dad was.
Likes For Retro Grouch: