Suntour hub bearings
#1
Senior Member
Thread Starter
Suntour hub bearings
I was going to service the bearings on this suntour hub off my Lotus Unique. They don't look like the way bearings come out on the 5 other Japanese bikes I've done. Do they require a special tool? The hub is stamped sealed bearings and they still seem to be very smooth
![](https://cimg8.ibsrv.net/gimg/bikeforums.net-vbulletin/2000x1504/20200805_211505_65d7b21cc716eb9f703c3de8b1db23df420d8c16.jpg)
#2
Senior Member
Join Date: Oct 2011
Location: Fairplay Co
Posts: 9,590
Bikes: Current 79 Nishiki Custum Sport, Jeunet 620, notable previous bikes P.K. Ripper loop tail, Kawahara Laser Lite, Paramount Track full chrome, Raliegh Internatioanl, Motobecan Super Mirage. 59 Crown royak 3 speed
Liked 1,864 Times
in
657 Posts
If there very smooth I would be tempted to leave them as is. These seal screw off with the correct size or adjustable spanner if you don't have the Suntour tool after that there just basic JIS style loose ball hubs pretty sure these are rebranded sanshin pros.
#3
Extraordinary Magnitude
Join Date: Aug 2009
Location: Waukesha WI
Posts: 13,674
Bikes: 1978 Trek TX700; 1978/79 Trek 736; 1984 Specialized Stumpjumper Sport; 1984 Schwinn Voyageur SP; 1985 Trek 620; 1985 Trek 720; 1986 Trek 400 Elance; 1987 Schwinn High Sierra; 1990 Miyata 1000LT
Liked 1,737 Times
in
951 Posts
I was told to just leave 'em. Ride 'em until they go.
__________________
*Recipient of the 2006 Time Magazine "Person Of The Year" Award*
Commence to jigglin’ huh?!?!
"But hey, always love to hear from opinionated amateurs." -says some guy to Mr. Marshall.
Commence to jigglin’ huh?!?!
"But hey, always love to hear from opinionated amateurs." -says some guy to Mr. Marshall.
#4
Senior Member
Join Date: Oct 2011
Location: Fairplay Co
Posts: 9,590
Bikes: Current 79 Nishiki Custum Sport, Jeunet 620, notable previous bikes P.K. Ripper loop tail, Kawahara Laser Lite, Paramount Track full chrome, Raliegh Internatioanl, Motobecan Super Mirage. 59 Crown royak 3 speed
Liked 1,864 Times
in
657 Posts
Why put the the removal notches on the seals if the hubs are semi fixed none service?
#6
Wrench Savant
![](https://cimg1.ibsrv.net/gimg/bikeforums.net-vbulletin/2000x1504/20200805_190256_2a4795f5198cb6b0b31f6517f684eb710d7ecfff.jpg)
You need one of these. The notched cap unscrews just like a bearing nut. The sealed cartridge bearings are a light press fit behind this retainer. The only one that does not have this retainer is the drive side of the rear hub, underneath the freewheel....at least for their road hubs. I have not pulled one of their MTB Sealed Bearing hubs apart in a long time.
I agree it is best to leave them along until they go.
Last edited by balindamood; 08-05-20 at 09:14 PM.
#7
Senior Member
+1 on leaving them unless they are rough. Since they are cartridge bearings, there are no cups or cones to become pitted. Once the bearings are done, you just replace the entire mechanism by pulling the old ones out and pressing in new ones. You can pull the seals off and add more grease if you like (member miamijim made a post about this years ago) but these bearings tend to last virtually forever so I wouldn't bother.
#8
Car free since 2018
Join Date: Aug 2017
Location: Vancouver, BC
Posts: 691
Bikes: Mostly japanese ones
Liked 270 Times
in
135 Posts
+1 on leaving them unless they are rough. Since they are cartridge bearings, there are no cups or cones to become pitted. Once the bearings are done, you just replace the entire mechanism by pulling the old ones out and pressing in new ones. You can pull the seals off and add more grease if you like (member miamijim made a post about this years ago) but these bearings tend to last virtually forever so I wouldn't bother.
#9
Senior Member
Join Date: May 2008
Location: Fredericksburg, Va
Posts: 9,635
Bikes: '65 Frejus TDF, '73 Bottecchia Giro d'Italia, '83 Colnago Superissimo, '84 Trek 610, '84 Trek 760, '88 Pinarello Veneto, '88 De Rosa Pro, '89 Pinarello Montello, '94 Burley Duet, 97 Specialized RockHopper, 2010 Langster, Tern Link D8
Liked 2,262 Times
in
1,129 Posts
rgvg Yup. I remember that one!
__________________
Bikes don't stand alone. They are two tired.
Bikes don't stand alone. They are two tired.
#10
I have two pairs of wheels with these hubs. One pair from a 1984 Miyata Ridge Runner still runs as smooth as the day they were new. The other pair from around 1984 were running rough after 30 years of service so I replaced the cartridge bearings which I easily found on Amazon and they run like new. I did not have the Suntour tool specified for this hub, so I used a makeshift tool to take them apart and put them back together again.
Note the rear hub was disassembled from the drive side so I did not have to use the makeshift tool. I currently use this wheelset on my commuter/touring bike.
Note the rear hub was disassembled from the drive side so I did not have to use the makeshift tool. I currently use this wheelset on my commuter/touring bike.
#11
Senior Member
Someone on ebay is selling re-pops of the Suntour TA-60 wrench used on these hubs. Search for "Suntour TA260 style' Sealed Wheel Hub Cone Spanner Wrench". He sells them by the pair, though, and you really only need one.
#12
Senior Member
Thread Starter
Thanks guys. I'll take the advise and leave them alone for now.
#13
Old fart
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,865
Bikes: Several, mostly not name brands.
Liked 3,472 Times
in
1,970 Posts
[MENTION=50984]balindamood[/MENTION] has the official SunTour TA-260 tool for those hubs. The hubs have sealed cartridge bearings; the aluminum pieces with the notches just set the preload on the cartridges. If the hubs are smooth, no service is needed.