Riding with a Patched Tube
#1
Senior Member
Thread Starter
Join Date: Feb 2021
Location: Bay Area
Posts: 75
Bikes: Specialized Aethos
Liked 108 Times
in
41 Posts
Riding with a Patched Tube
Let’s say you were on ride and had flat, which you patched and put back on to complete your ride home. When you get home do you remove/trash the patched tube and replace with a new tube or do you continue ride with the patched tube until it flats again then replace? Just curious, what others do.
#2
Senior Member
Join Date: Oct 2017
Location: Chapel Hill NC
Posts: 1,683
Bikes: 2000 Litespeed Vortex Chorus 10, 1995 DeBernardi Cromor S/S
Liked 797 Times
in
446 Posts
Let’s say you were on ride and had flat, which you patched and put back on to complete your ride home. When you get home do you remove/trash the patched tube and replace with a new tube or do you continue ride with the patched tube until it flats again then replace? Just curious, what others do.
#3
Senior Member
Back in the day, I'd put a new one in on the side of the road and decide whether to patch the old one when I got home. But then I stopped using tubes and getting flats.
Likes For Seattle Forrest:
#4
Senior Member
Let’s say you were on ride and had flat, which you patched and put back on to complete your ride home. When you get home do you remove/trash the patched tube and replace with a new tube or do you continue ride with the patched tube until it flats again then replace? Just curious, what others do.
#5
Senior Member
Since the glue was changed in patch kits, I haven't had much luck with them. I carry a new spare tube. I still have a patch kit in the bag, as a last resort. To answer the question, yes, I would replace and trash the patched tube with a new tube as soon as possible.
#6
Senior Member
Join Date: Jul 2002
Location: Sacramento, California, USA
Posts: 40,865
Bikes: Specialized Tarmac, Canyon Exceed, Specialized Transition, Ellsworth Roots, Ridley Excalibur
Liked 3,110 Times
in
1,418 Posts
If done properly, the patch is a permanent fix. Just leave it and ride on.
Likes For caloso:
#7
Senior Member
I never replace a tube unless it is irreparably damaged. I am mostly riding tubeless these days, but when I was using tubes, most would accumulate multiple patches. There are times when a patch will not work, such as a puncture or tear near the valve stem. But for successfully applied patches, I have never had one fail. Subsequent leaks in the same tube are always from a puncture elsewhere.
Last edited by mihlbach; 05-07-21 at 05:46 AM.
#8
Expired Member
I rarely give up on a tube because of patches. It's amusing to see how many can accumulate. The tube may eventually fail near or at the valve and get tossed. I don't normally patch while on a ride but will patch and reinstall the punctured tube at home. That way I know the patch is good and/or there isn't another puncture I've missed.
Likes For shelbyfv:
#9
Senior Member
Thread Starter
Join Date: Feb 2021
Location: Bay Area
Posts: 75
Bikes: Specialized Aethos
Liked 108 Times
in
41 Posts
I myself have done it both ways. I carry one spare tube on my rides with a patch kit. I will change tube on the side of the road and patch the other later. I will discard the popped tube if the "snake bite" can not be covered by a patch, otherwise I patch and reuse.
#10
Very Senior Member
Join Date: Mar 2018
Location: Always on the Run
Posts: 1,212
Bikes: More than last week
Liked 344 Times
in
245 Posts
I keep new tubes at home base and only carry patch kit. If I make it home without losing pressure, I ride it till it leaks again. Patches don't bother me and only chuck tubes if they're not patchable. IE:valve stem damage.
#11
Senior Member
I'm lazy and tubes are cheap. Replace the tube with a spare on the roadside, throw it away when I get home.
#12
Should Be More Popular
Join Date: Dec 2007
Location: Malvern, PA (20 miles West of Philly)
Posts: 43,317
Bikes: 1986 Alpine (steel road bike), 2009 Ti Habenero, 2013 Specialized Roubaix
Liked 9,221 Times
in
4,273 Posts
Clarification, there are two types of patches:
1. Traditional patches with vulcanizing fluid "glue" these are permanent.
2. Newer "peel/stick" patches which are designed to be temporary and are NOT permanent. I am sure someone will chime in that he got a permanent repair with one of these, but I would advise you NOT consider them permanent.
1. Traditional patches with vulcanizing fluid "glue" these are permanent.
2. Newer "peel/stick" patches which are designed to be temporary and are NOT permanent. I am sure someone will chime in that he got a permanent repair with one of these, but I would advise you NOT consider them permanent.
Likes For datlas:
#13
Over the hill
Join Date: Mar 2006
Location: Los Angeles, CA
Posts: 24,418
Bikes: Giant Defy, Giant Revolt
Liked 1,259 Times
in
714 Posts
Clarification, there are two types of patches:
1. Traditional patches with vulcanizing fluid "glue" these are permanent.
2. Newer "peel/stick" patches which are designed to be temporary and are NOT permanent. I am sure someone will chime in that he got a permanent repair with one of these, but I would advise you NOT consider them permanent.
1. Traditional patches with vulcanizing fluid "glue" these are permanent.
2. Newer "peel/stick" patches which are designed to be temporary and are NOT permanent. I am sure someone will chime in that he got a permanent repair with one of these, but I would advise you NOT consider them permanent.
When I first started using those sticker patches, I did in fact think they were permanent. That caused a problem when they started to fail out on the road, including the spare which had a couple of stickers on as well, and putting a fresh sticker over an old sticker was futile.
__________________
It's like riding a bicycle
It's like riding a bicycle
#14
Advocatus Diaboli
Join Date: Feb 2015
Location: Wherever I am
Posts: 8,739
Bikes: Merlin Cyrene, Nashbar steel CX
Liked 1,565 Times
in
1,028 Posts
A couple factors worth considering -- patches do add rotating weight, plus can lead to wheel imbalances. So there is that..
#15
just another gosling
Join Date: Feb 2007
Location: Everett, WA
Posts: 19,638
Bikes: CoMo Speedster 2003, Trek 5200, CAAD 9, Fred 2004
Liked 2,005 Times
in
1,424 Posts
I admit to being a stickler for using good tubes: I put a 6 patch limit on any tube. I've never had a patch failure in the past 25 years. I always ride with 2 tubes, patch kit, boot kit, and a spare tire. I loan that stuff more than I use it, but I've been riding long enough that I've used all of that stuff myself at least once. The great thing about the spare tire is that I never have to hold anyone up looking for the frigging radial wire in my tire. I just put a fresh tube, probably patched, in my spare tire and I'm back on the road in 5 minutes. And I never have a tire failure I can't fix,
__________________
Results matter
Results matter
#16
Should Be More Popular
Join Date: Dec 2007
Location: Malvern, PA (20 miles West of Philly)
Posts: 43,317
Bikes: 1986 Alpine (steel road bike), 2009 Ti Habenero, 2013 Specialized Roubaix
Liked 9,221 Times
in
4,273 Posts
#17
Advocatus Diaboli
Join Date: Feb 2015
Location: Wherever I am
Posts: 8,739
Bikes: Merlin Cyrene, Nashbar steel CX
Liked 1,565 Times
in
1,028 Posts
#18
Should Be More Popular
Join Date: Dec 2007
Location: Malvern, PA (20 miles West of Philly)
Posts: 43,317
Bikes: 1986 Alpine (steel road bike), 2009 Ti Habenero, 2013 Specialized Roubaix
Liked 9,221 Times
in
4,273 Posts
#19
Advocatus Diaboli
Join Date: Feb 2015
Location: Wherever I am
Posts: 8,739
Bikes: Merlin Cyrene, Nashbar steel CX
Liked 1,565 Times
in
1,028 Posts
#20
In 60,000+ miles of road cycling on crappy Massachusetts roads I've had one patch fail, and that was a few weeks ago. The mistake that I made was using on the front wheel. No harm, it went down slowly. Most likely a poor patch job by me.
Other than that, no problems at all.
'll go with three patches before I trash a tube. I tried tubeless, but with Schwalbe One tires, I got a leak almost every ride. I got tired of cleaning sealant off my frame.
I have no problem using patched tubes.
Other than that, no problems at all.
'll go with three patches before I trash a tube. I tried tubeless, but with Schwalbe One tires, I got a leak almost every ride. I got tired of cleaning sealant off my frame.
I have no problem using patched tubes.
#21
Full Member
Join Date: Jul 2015
Location: Chicago
Posts: 309
Bikes: nothing to brag about
Liked 206 Times
in
116 Posts
They put in sandpaper for a reason, and you really need to rough up the surface AND removed the oxidized outer layer, so do more than you would every think you need to do. Then after putting the patch on, burnish it in place, thoroughly. If you skip this, it won't stick.
I have had the same experience with both nylon jacket repair tape and adhesive velcro. You MUST burnish adhesives, hard, so that they go into the fabric (or fubber) thoroughly and are defintely pressed in place. I use the edge of a coin for this on all three types, tires, nylon, velcro, and there's never a problem after that. Just laying any of these on with a bit of thumb rubbing won't do it.
If you read reviews of any of these three, you'll see that there are plenty of people who can't get them to stick, but it's not a problem with the adhesive.
#22
Asleep at the bars
Join Date: May 2006
Location: San Francisco, CA and Treasure Island, FL
Posts: 1,743
Liked 203 Times
in
135 Posts
Going on two years now without a single flat on tubeless. To me it's a solved problem.
![Smilie](images/smilies/smile.gif)
I have a friend I used to ride with who would insist on taking my old tubes home and patching them. As far as I know he has an entire garage worth of old tubes and 99% threadbare tires. Not that he ever uses or needs any of them.
__________________
"This 7:48 cycling session burned 5933 calories. Speed up recovery by replacing them with a healthy snack." - Whoop
"This 7:48 cycling session burned 5933 calories. Speed up recovery by replacing them with a healthy snack." - Whoop
#23
Senior Member
Join Date: Sep 2007
Location: Far beyond the pale horizon.
Posts: 14,458
Liked 1,454 Times
in
1,009 Posts
#24
Senior Member
Join Date: Oct 2014
Location: Portland, OR
Posts: 13,060
Bikes: (2) ti TiCycles, 2007 w/ triple and 2011 fixed, 1979 Peter Mooney, ~1983 Trek 420 now fixed and ~1973 Raleigh Carlton Competition gravel grinder
Liked 4,089 Times
in
2,643 Posts
Let’s say you were on ride and had flat, which you patched and put back on to complete your ride home. When you get home do you remove/trash the patched tube and replace with a new tube or do you continue ride with the patched tube until it flats again then replace? Just curious, what others do.
I do carry 2 tubes (new or patched). I've had long cuts in tires, blowouts, broken valve stems/leaks at the base and some days the Gods aren't smiling. And the single best way to get that Murphy guy to behave is to be prepared.
#25
Senior Member