General advice on bike repair?
#1
Newbie
Thread Starter
Join Date: Sep 2022
Posts: 13
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 3 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
General advice on bike repair?
Hello, everyone! I just purchased an 86 Bianchi Special in purple and want to convert it to single-speed/fixed-gear. Eventually, I'd like to update all, if not most, of the components. First question, is there anything I should know (as far as general maintenance goes) prior to repairing this bike by myself?
Second, do you all recommend any websites for purchasing good parts? Right now, I'm considering purchasing a wheelset, but am unsure where to buy it from.
Anyway, super stoked to be a part of this forum!
Second, do you all recommend any websites for purchasing good parts? Right now, I'm considering purchasing a wheelset, but am unsure where to buy it from.
Anyway, super stoked to be a part of this forum!
#2
mechanically sound
If sheldon brown’s website is still around, it has almost everything you need to know.
__________________
Likes For frankenmike:
#3
Senior Member
Join Date: Jun 2002
Location: Montreal, Quebec
Posts: 6,039
Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 1876 Post(s)
Liked 1,751 Times
in
1,015 Posts
If the bike has vertical rear dropouts conversion to single speed will be a big challenge
#4
Senior Member
Join Date: Feb 2012
Location: Golden, CO and Tucson, AZ
Posts: 2,854
Bikes: 2012 Specialized Elite Disc, 1983 Trek 520
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 682 Post(s)
Liked 767 Times
in
438 Posts
First be sure the seat post and handle bar stem move. If they do, grease them up now.
If it has 27" wheels now and you want to change it to 700C, verify the brake shoes have at least 4 mm of free movement in the caliper toward the axle.
If it has 27" wheels now and you want to change it to 700C, verify the brake shoes have at least 4 mm of free movement in the caliper toward the axle.
Likes For andrewclaus:
#5
Guest
Join Date: Sep 2020
Posts: 2,888
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 1346 Post(s)
Liked 3,271 Times
in
1,439 Posts
That's not a bike I'd choose to convert, but good luck to you. If it's the same frame as the photo, be prepared to experiment with gear ratios, as the dropouts give you very little room to tension the chain. You'll likely need compromise your desired gear combo to make it work.
Last edited by Rolla; 10-03-22 at 03:08 PM.
Likes For Rolla:
#6
Senior Member
Join Date: Apr 2009
Location: New Rochelle, NY
Posts: 39,061
Bikes: too many bikes from 1967 10s (5x2)Frejus to a Sumitomo Ti/Chorus aluminum 10s (10x2), plus one non-susp mtn bike I use as my commuter
Mentioned: 141 Post(s)
Tagged: 1 Thread(s)
Quoted: 5976 Post(s)
Liked 2,883 Times
in
1,604 Posts
That will solve the problem if he's riding single speed free wheel. But if he's planning to use fixed gear there will be issues with the backlash when he tries to brake. The degree of problem really depends on the amount of slack in the lower loop.
FWIW the OP doesn't even have to spend money for that idler arm he can simply keep the derailleur locked in directly under his one sprocket.
__________________
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
#8
Senior Member
Join Date: Feb 2012
Location: Golden, CO and Tucson, AZ
Posts: 2,854
Bikes: 2012 Specialized Elite Disc, 1983 Trek 520
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 682 Post(s)
Liked 767 Times
in
438 Posts
If you don't match the existing dropout spacing, you should change the spacing. See this article: https://www.sheldonbrown.com/frame-spacing.html
I've cold set several older frames for updated hubs, but I've had access to shop tools and help. If there's a bike co-op in your area, that'll be a great resource.
I've cold set several older frames for updated hubs, but I've had access to shop tools and help. If there's a bike co-op in your area, that'll be a great resource.
#9
Guest
Join Date: Sep 2020
Posts: 2,888
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 1346 Post(s)
Liked 3,271 Times
in
1,439 Posts
#10
Old fart
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,844
Bikes: Several, mostly not name brands.
Mentioned: 154 Post(s)
Tagged: 0 Thread(s)
Quoted: 3617 Post(s)
Liked 3,454 Times
in
1,960 Posts
Likes For JohnDThompson:
#11
Senior Member
Join Date: Mar 2007
Location: SF Bay Area, East bay
Posts: 7,761
Bikes: Miyata 618 GT, Marinoni, Kestral 200 2002 Trek 5200, KHS Flite, Koga Miyata, Schwinn Spitfire 5, Mondia Special, Univega Alpina, Miyata team Ti, Santa Cruz Highball
Mentioned: 54 Post(s)
Tagged: 0 Thread(s)
Quoted: 1638 Post(s)
Liked 2,734 Times
in
1,270 Posts
You should browse here... https://www.bikeforums.net/singlespeed-fixed-gear/
Whatever you do, don't start hacking off parts. That would get you branded as a 'drew.
Whatever you do, don't start hacking off parts. That would get you branded as a 'drew.
#12
Professional amateur
Join Date: May 2018
Location: Ga.
Posts: 688
Bikes: Does a Big Wheel count ?
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 302 Post(s)
Liked 136 Times
in
92 Posts
Though their selection can be limited and kind of off-the-wall, a good site to check for random bike parts is....well....um.....Random Bike Parts !
Ive snagged a couple good parts and a nice frame from them. And, they do free shipping.
Ive snagged a couple good parts and a nice frame from them. And, they do free shipping.