Dahon Mariner D8 Fixing Steering
#1
Dahon Mariner D8 Fixing Steering
I tried to tighten handle post on my Dahon Mariner D8 tonight and I think something went wrong and that little square white plastic thing that is placed between the hinge bolt and a lever popped out. I tried to put it back on a bolt, by pushing hinge back but it doesn't go back enough to fit that part back in. I'm not sure how it even popped out.
Does anyone know what to do with it? I guess I need to undo screws of the hinge and put that white thing back on that way. But there are springs inside the hinge and I'm not sure if it's even safe to undo these screws and if I can put it all back myself after it.
Here are the photos:
Does anyone know what to do with it? I guess I need to undo screws of the hinge and put that white thing back on that way. But there are springs inside the hinge and I'm not sure if it's even safe to undo these screws and if I can put it all back myself after it.
Here are the photos:
#2
Alright, I took this metal hinge out by undoing the screws. Springs popped out as I expected, but I managed to turn it a bit and slide this plastic piece back in. Then I tucked springs back next to the bolts. So apparently when I tightened both bolts too much they pressed against this plastic part too much and prevented a hinge from moving when folding. This applied too much pressure on a plastic part and it popped off. Loosening the bolts properly and balancing them out so they are both tight but loose enought to allow hinge movement resulted in a plastic piece staying in place and folding mechanism working as it should. I'm happy I didn't break anything, hopefully nothing cracks when I commute 20 miles tomorrow haha.
#3
Freewheel Medic
Join Date: Oct 2005
Location: An Island on the Coast of GA!
Posts: 12,938
Bikes: Snazzy* Schwinns, Classy Cannondales & a Super Pro Aero Lotus (* Ed.)
Liked 2,259 Times
in
995 Posts
Thanks for sharing your experience. I'm certain it will help other Dahon and other folding bike owners in the future. Hopefully your commute is uneventful!
__________________
Bob
Enjoying the GA coast all year long!
Thanks for visiting my website: www.freewheelspa.com
Bob
Enjoying the GA coast all year long!
Thanks for visiting my website: www.freewheelspa.com
#5
Senior Member
Join Date: Feb 2005
Location: SW Florida
Posts: 1,684
Bikes: '06 Bianchi Pista; '57 Maclean; '10 Scott CR1 Pro; 2005 Trek 2000 Tandem; '09 Comotion Macchiato Tandem; 199? Novara Road; '17 Circe Helios e-tandem:1994 Trek 2300
Liked 99 Times
in
66 Posts
Alright, I took this metal hinge out by undoing the screws. Springs popped out as I expected, but I managed to turn it a bit and slide this plastic piece back in. Then I tucked springs back next to the bolts. So apparently when I tightened both bolts too much they pressed against this plastic part too much and prevented a hinge from moving when folding. This applied too much pressure on a plastic part and it popped off. Loosening the bolts properly and balancing them out so they are both tight but loose enought to allow hinge movement resulted in a plastic piece staying in place and folding mechanism working as it should. I'm happy I didn't break anything, hopefully nothing cracks when I commute 20 miles tomorrow haha.
#6
Senior Member
Fyi & fwiw
CFYI & FWIW, contemporary handle posts look like this. Seeing your image I was at a loss for what you were describing. The tightening is done via an external hex bolt so there's no need to fold or open the handlepost.
Last edited by Ron Damon; 01-13-23 at 08:37 PM.
#7
Senior Member
Also, the metal plate is spring loaded so you can push it away from the hinge and make even more space
#8
Senior Member
Join Date: Feb 2005
Location: SW Florida
Posts: 1,684
Bikes: '06 Bianchi Pista; '57 Maclean; '10 Scott CR1 Pro; 2005 Trek 2000 Tandem; '09 Comotion Macchiato Tandem; 199? Novara Road; '17 Circe Helios e-tandem:1994 Trek 2300
Liked 99 Times
in
66 Posts
Thanks for your reply
My problem is not getting the block in, but one of the springs keeps popping out.
#9
Senior Member
Are the hex screws holding in the springs missing?
The locking plate is held in by 2 screws and there are two more small set screws that hold the springs in and are only accessible if you remove the locking plate (the big silver sliding plate)
The set screws are on the same side as the white plastic block
#10
Senior Member
Join Date: Feb 2005
Location: SW Florida
Posts: 1,684
Bikes: '06 Bianchi Pista; '57 Maclean; '10 Scott CR1 Pro; 2005 Trek 2000 Tandem; '09 Comotion Macchiato Tandem; 199? Novara Road; '17 Circe Helios e-tandem:1994 Trek 2300
Liked 99 Times
in
66 Posts
Ah. ok
Are the hex screws holding in the springs missing?
The locking plate is held in by 2 screws and there are two more small set screws that hold the springs in and are only accessible if you remove the locking plate (the big silver sliding plate)
The set screws are on the same side as the white plastic block
Are the hex screws holding in the springs missing?
The locking plate is held in by 2 screws and there are two more small set screws that hold the springs in and are only accessible if you remove the locking plate (the big silver sliding plate)
The set screws are on the same side as the white plastic block
No. I'm a bit of a twit: We have two Dahons which I am about to give away to friends as we no longer need them. The bikes have not been used for years and when I lifted the bars to lock in place one of them, the sliding wedge/locking plate didn't move, so I decided to take it apart and grease the sliding surfaces, not realizing the presence of the small springs, one of which popped out. I have tried removing the small set screws and inserting the spring, but when I put the locking plate screw in, the spring becomes misaligned or pops out. I guess it's all up to my dexterity, which is obviously lacking, to get it together. At the moment, the air in my garage is blue!! But I'll keep trying. Thanks for your advice.
The other Dahon had the same problem initially, but after the above experience, I gave the locking plate a squirt of WD40 and it fixed it.
#11
Senior Member
No. I'm a bit of a twit: We have two Dahons which I am about to give away to friends as we no longer need them. The bikes have not been used for years and when I lifted the bars to lock in place one of them, the sliding wedge/locking plate didn't move, so I decided to take it apart and grease the sliding surfaces, not realizing the presence of the small springs, one of which popped out. I have tried removing the small set screws and inserting the spring, but when I put the locking plate screw in, the spring becomes misaligned or pops out. I guess it's all up to my dexterity, which is obviously lacking, to get it together. At the moment, the air in my garage is blue!! But I'll keep trying. Thanks for your advice.
The other Dahon had the same problem initially, but after the above experience, I gave the locking plate a squirt of WD40 and it fixed it.
The other Dahon had the same problem initially, but after the above experience, I gave the locking plate a squirt of WD40 and it fixed it.
Leave the set screws in.
If you have a pick (metal or wood) you should be able to align the springs when installing the screws on the plate.
It's not an ideal design.
Dahons always being joy into your life.
The day you get one and the day you get rid of it.
#12
Senior Member
Join Date: Feb 2005
Location: SW Florida
Posts: 1,684
Bikes: '06 Bianchi Pista; '57 Maclean; '10 Scott CR1 Pro; 2005 Trek 2000 Tandem; '09 Comotion Macchiato Tandem; 199? Novara Road; '17 Circe Helios e-tandem:1994 Trek 2300
Liked 99 Times
in
66 Posts
ok I remember now.
Leave the set screws in.
If you have a pick (metal or wood) you should be able to align the springs when installing the screws on the plate.
It's not an ideal design.
Dahons always being joy into your life.
The day you get one and the day you get rid of it.
Leave the set screws in.
If you have a pick (metal or wood) you should be able to align the springs when installing the screws on the plate.
It's not an ideal design.
Dahons always being joy into your life.
The day you get one and the day you get rid of it.
Thanks for your time.
Likes For Artmo:
#13
Senior Member
Join Date: Sep 2004
Location: Chicago area
Posts: 2,579
Bikes: Airborne "Carpe Diem", Motobecane "Mirage", Trek 6000, Strida 2, Dahon "Helios XL", Dahon "Mu XL", Tern "Verge S11i"
Liked 596 Times
in
407 Posts
I have a Dahon Mu XL that I've had since 2006. The handlepost is like the OP's and I've replaced the white plastic block several times over the course of over 12,000 miles.
FWIW, I have enjoyed this bike the entire time I've owned it. I've been using it as my "winter" bike since I got a Tern Verge S11i in 2013, and the salt here in Chicago has finally destroyed the frame. It does not give me any joy to retire the bike; I used it hard and it did its job well.
The Mu XL "Winter" about 5 years ago. It was already pretty well thrashed by then. Notice the cracked seat tube.
Last edited by sweeks; 01-14-23 at 09:31 PM.
Likes For sweeks:
Thread
Thread Starter
Forum
Replies
Last Post
akcapbikeforums
Folding Bikes
6
11-15-11 09:03 PM
jenna1224
Folding Bikes
9
08-10-11 03:58 PM