Need help with cones
#26
Senior Member
Join Date: Oct 2011
Location: Ellensburg,WA
Posts: 3,193
Bikes: Schwinn Broadway, Specialized Secteur Sport(crashed) Spec. Roubaix Sport, Spec. Crux
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 186 Post(s)
Liked 176 Times
in
88 Posts
Okay now I see where you are coming from. Just guessing but most folks (not pro bike mechanics) probably have measurement tools that are not metric. Having to do a conversion isn't a terrible thing. To insist that those with imperial measuring tools convert to your chosen standard seems to be arrogant snobbery to me.
__________________
Sir Mark, Knight of Sufferlandria
Sir Mark, Knight of Sufferlandria
#27
señor miembro
Join Date: Dec 2018
Location: Pac NW
Posts: 6,661
Bikes: '70s - '80s Campagnolo
Mentioned: 93 Post(s)
Tagged: 0 Thread(s)
Quoted: 3921 Post(s)
Liked 6,560 Times
in
3,251 Posts
#28
Senior Member
Join Date: Dec 2020
Location: Wake Forest, NC
Posts: 5,939
Bikes: 1989 Cinelli Supercorsa
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
Quoted: 3608 Post(s)
Liked 3,027 Times
in
1,832 Posts
Likes For smd4:
#29
señor miembro
Join Date: Dec 2018
Location: Pac NW
Posts: 6,661
Bikes: '70s - '80s Campagnolo
Mentioned: 93 Post(s)
Tagged: 0 Thread(s)
Quoted: 3921 Post(s)
Liked 6,560 Times
in
3,251 Posts
#30
Senior Member
Join Date: Jun 2020
Location: Maryland
Posts: 1,380
Bikes: 1982 Bianchi Sport SX, Rayleigh Tamland 1, Rans V-Rex recumbent, Fuji MTB, 80's Cannondale MTB with BBSHD ebike motor
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 668 Post(s)
Liked 529 Times
in
355 Posts
SAE standards are not standards? Lots of things still use imperial units. Military hardware is still obstinately imperial units.
Lots of bike parts are still imperial units. Like headsets, pedals, bottom brackets. The only thing standard on bikes through the years have been all the new standards.
Learn to think in two sets of units. Sort of like being bilingual. Or buy a digital caliper. They usually support either sets of units.
Likes For Pop N Wood:
#31
aged to perfection
Join Date: Jun 2009
Location: PacNW
Posts: 1,857
Bikes: Dinucci Allez 2.0, Richard Sachs, Alex Singer, Serotta, Masi GC, Raleigh Pro Mk.1, Hetchins, etc
Mentioned: 24 Post(s)
Tagged: 0 Thread(s)
Quoted: 852 Post(s)
Liked 1,282 Times
in
676 Posts
one possible reason for the persistence of imperial (fractional inch) units in the bike industry is that after WW2 the italian industrial base was re-tooled with machine tools from the US and England.
Those machines did not have metric lead screws. So they could turn a metric diameter but could ony cut threads of imperial dimension.
at least that is how it was once explained to me. Portlandjim might have more to say about that.
/markp
Those machines did not have metric lead screws. So they could turn a metric diameter but could ony cut threads of imperial dimension.
at least that is how it was once explained to me. Portlandjim might have more to say about that.
/markp
#32
Senior Member
Join Date: Apr 2009
Location: New Rochelle, NY
Posts: 38,952
Bikes: too many bikes from 1967 10s (5x2)Frejus to a Sumitomo Ti/Chorus aluminum 10s (10x2), plus one non-susp mtn bike I use as my commuter
Mentioned: 141 Post(s)
Tagged: 1 Thread(s)
Quoted: 5907 Post(s)
Liked 2,776 Times
in
1,548 Posts
one possible reason for the persistence of imperial (fractional inch) units in the bike industry is that after WW2 the italian industrial base was re-tooled with machine tools from the US and England.
Those machines did not have metric lead screws. So they could turn a metric diameter but could ony cut threads of imperial dimension.
at least that is how it was once explained to me. Portlandjim might have more to say about that.
/markp
Those machines did not have metric lead screws. So they could turn a metric diameter but could ony cut threads of imperial dimension.
at least that is how it was once explained to me. Portlandjim might have more to say about that.
/markp
This is absolutely correct. Before the advent of CNC, machinery took measurements based on the pitch of a lead screw. Since, there is no rational multiplier for converting metric to imperial or vice versa, machines could only produce threaded parts based on their own lead screw.
Note, the above applies only to "generated" threads. Those that were made with taps and dies were unaffected, since the tooling had enough float to correct for error.
Last edited by FBinNY; 07-06-23 at 04:37 PM.
#33
Senior Member
Join Date: Jul 2005
Location: Boulder County, CO
Posts: 4,431
Bikes: '80 Masi Gran Criterium, '12 Trek Madone, early '60s Frejus track
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 523 Post(s)
Liked 459 Times
in
345 Posts
I see some pitting. Do what the pros do. Wheels Mfg. makes replacement cones and axles. Measure the axle diameter, the small diameter of the race, the length of the race, the large diameter of the race, and the overall length of the cone. Match taper of the race by eyeball at https://wheelsmfg.com/products/hub-parts/all-cones.html. If you replace the axle, too, you won't have to measure the threads. Or take the axle to your local bike shop hand have them measure and order.
#34
Dirt Bomb
Thread Starter
Join Date: Aug 2006
Location: Illinois
Posts: 2,873
Mentioned: 64 Post(s)
Tagged: 0 Thread(s)
Quoted: 5596 Post(s)
Liked 294 Times
in
245 Posts
This cone from https://wheelsmfg.com/products/hub-p...s/cn-r082.html seems to fit the bill. (I still need to find out what size ball bearing that takes before I order. Anybody know offhand? Mine are .187"/4.75mm)
Thanks again.
__________________
Last edited by sknhgy; 07-08-23 at 11:44 AM.
#35
Dirt Bomb
Thread Starter
Join Date: Aug 2006
Location: Illinois
Posts: 2,873
Mentioned: 64 Post(s)
Tagged: 0 Thread(s)
Quoted: 5596 Post(s)
Liked 294 Times
in
245 Posts
Two of those cones, plus shipping from Wheels Mfg comes to $40.69. I'm going to hit up some more bike shops before ordering there.
Thanks for all the help.
Thanks for all the help.
__________________
#36
Senior Member
Join Date: Apr 2007
Posts: 6,845
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 1138 Post(s)
Liked 1,238 Times
in
784 Posts
Nothing you can do to improve the cones. These surfaces are loosely akin to ice crusted snow, namely a hard surface covering a softer core. Polishing will only remove more o f the critical hard skin.
There are sources for replacement cones, if not an exact match, at least close enough to serve well. However the seals are much harder to find, if at all.
Looking at them, they're not terrible, and in your shoes, I'd use new balls, good quality grease, and careful adjustment to minimum preload. Then ride.
BTW while this wear will feel rough when spinning the axle in your fingers, the actual difference when riding is about as close to zero as one can imagine.
There are sources for replacement cones, if not an exact match, at least close enough to serve well. However the seals are much harder to find, if at all.
Looking at them, they're not terrible, and in your shoes, I'd use new balls, good quality grease, and careful adjustment to minimum preload. Then ride.
BTW while this wear will feel rough when spinning the axle in your fingers, the actual difference when riding is about as close to zero as one can imagine.
I found some cones for old campy hubs I was trying to re-hab for a vintage Italian build I was doing and found some similar-period rims and hubs. (also my first wheel build). I can't really remember the details, but I found some from, IIRC, Wheels Manufacturing using some pretty simple measurements. The hub is smooth seems to work well even though I'm pretty sure the the cones weren't identical.
In retrospect, I probably could have gotten away with just using the imperfect cones with new balls, grease and careful pre-load as you suggest, and accepted a tiny bit of roughness that was present before I started. But it was a fun project.
I have been totally self taught in bike mechanics beginning in the 70s with "Glen's" encyclopedic book on bike repair. But never any "hands on" mentoring or instruction. I always thought that wheel bearings needed to be perfectly smooth, or darn close to it. Only recently has a respected professional mechanic told me - in reference to a different cone and cup wheel bearing I was messing with that was a little rough: "that's just fine". I never realized!
Last edited by Camilo; 07-11-23 at 10:45 PM.