Folding Bike frame hinge bolts
#1
BeastMaster
Thread Starter
Folding Bike frame hinge bolts
I’ve got a Retrospec “Spec” (Judd) folding bike that I’ve modified over the years. I’ve noticed the frame hinge bolts are starting to corrode. Looking for advice on replacing these with a more corrosion resistant (titanium?) fastener. Any takers?
![](https://cimg4.ibsrv.net/gimg/bikeforums.net-vbulletin/2000x1504/image_77d294c30b12874aa122934e0d72b56455afe035.jpg)
Top view- top hinge bolt
![](https://cimg0.ibsrv.net/gimg/bikeforums.net-vbulletin/2000x1504/image_bf8c29c21f86e99cd210db100c716364a21344a1.jpg)
Bottom view- bottom hinge bolt
![](https://cimg4.ibsrv.net/gimg/bikeforums.net-vbulletin/2000x1504/image_77d294c30b12874aa122934e0d72b56455afe035.jpg)
Top view- top hinge bolt
![](https://cimg0.ibsrv.net/gimg/bikeforums.net-vbulletin/2000x1504/image_bf8c29c21f86e99cd210db100c716364a21344a1.jpg)
Bottom view- bottom hinge bolt
#2
I'm good to go!
Join Date: Jul 2017
Location: Mississippi
Posts: 15,265
Bikes: Tarmac Disc Comp Di2 - 2020
Mentioned: 52 Post(s)
Tagged: 0 Thread(s)
Quoted: 6344 Post(s)
Liked 4,945 Times
in
3,405 Posts
Anything special about the part of the bolt we can't see? Big long shoulder and a few threads on the other end that are significantly smaller diameter? Might just get several of the same and just change them out as they get cosmetically unattractive to you.
If the it's just the head that's rusty, then clean it up and put some paint on it. Maybe just a zinc primer or some cold galvanize spray paint.
If the it's just the head that's rusty, then clean it up and put some paint on it. Maybe just a zinc primer or some cold galvanize spray paint.
Likes For Iride01:
#3
Senior Member
Join Date: Jul 2015
Location: NW Oregon
Posts: 2,986
Bikes: !982 Trek 930R Custom, Diamondback ascent with SERIOUS updates, Fuji Team Pro CF and a '09 Comencal Meta 5.5
Mentioned: 15 Post(s)
Tagged: 1 Thread(s)
Quoted: 1301 Post(s)
Liked 745 Times
in
539 Posts
Most hardware stores stock Stainless Steel bolts, screws, and nuts in a variety of configurations.
titanium can also corrode... and may cause surrounding materials to fail.
just curious,, how often do you actually "fold" the bike?
titanium can also corrode... and may cause surrounding materials to fail.
just curious,, how often do you actually "fold" the bike?
Likes For maddog34:
#4
BeastMaster
Thread Starter
Anything special about the part of the bolt we can't see? Big long shoulder and a few threads on the other end that are significantly smaller diameter? Might just get several of the same and just change them out as they get cosmetically unattractive to you.
If the it's just the head that's rusty, then clean it up and put some paint on it. Maybe just a zinc primer or some cold galvanize spray paint.
If the it's just the head that's rusty, then clean it up and put some paint on it. Maybe just a zinc primer or some cold galvanize spray paint.
![](https://cimg5.ibsrv.net/gimg/bikeforums.net-vbulletin/1159x1545/img_1755_cbdd1c1d76c22f32a087c94f3b7632bcf0bb99c2.jpeg)
#5
BeastMaster
Thread Starter
Will look into sealants to protect the bolt head. I fold both my folding bikes (also have a Dahon Mu) quite often, 2-3X a week, loading into my car or entering an establishment.
Last edited by Need41speed; 09-29-23 at 03:30 PM.
#6
Senior Member
Join Date: Jul 2015
Location: NW Oregon
Posts: 2,986
Bikes: !982 Trek 930R Custom, Diamondback ascent with SERIOUS updates, Fuji Team Pro CF and a '09 Comencal Meta 5.5
Mentioned: 15 Post(s)
Tagged: 1 Thread(s)
Quoted: 1301 Post(s)
Liked 745 Times
in
539 Posts
salty air does bad things to plain steel.
salt is a chloride.
soak the stock hinge pins with penetrant oil now.
Likes For maddog34:
#7
Senior Member
Join Date: Apr 2011
Location: Maryland, USA
Posts: 2,501
Bikes: Drysdale/Gitane/Zeus/Masi/Falcon/Palo Alto/Raleigh/Legnano
Mentioned: 34 Post(s)
Tagged: 0 Thread(s)
Quoted: 1021 Post(s)
Liked 702 Times
in
430 Posts
That part, and that part alone, reminds me of what I've read about aviation bolts, specc'ed by "grip length". Alas, that's all I've ever read about them and never utilized any...
![](https://cimg0.ibsrv.net/gimg/bikeforums.net-vbulletin/400x373/04_01030_f24dc74c797fadc31056a0d074f3f10de41faebf.jpg)
__________________
Larry:1958 Drysdale, 1961 Gitane Gran Sport, 1974 Zeus track, 1988 Masi Gran Corsa, 1974 Falcon, 1980 Palo Alto, 1973 Raleigh Gran Sport, 1974 Legnano. Susan: 1976 Windsor Profesional.
Larry:1958 Drysdale, 1961 Gitane Gran Sport, 1974 Zeus track, 1988 Masi Gran Corsa, 1974 Falcon, 1980 Palo Alto, 1973 Raleigh Gran Sport, 1974 Legnano. Susan: 1976 Windsor Profesional.
Likes For tiger1964:
#9
I am potato.
Join Date: Jun 2015
Location: Pacific Northwest
Posts: 3,168
Bikes: Only precision built, custom high performance elitist machines of the highest caliber. 🍆
Mentioned: 30 Post(s)
Tagged: 0 Thread(s)
Quoted: 1820 Post(s)
Liked 1,695 Times
in
969 Posts
I'll wager that it is an unusual fastener type. One end is a long barrel that is the full diameter of the hole and fills the hinge from end to end for the full length. The other end is a standard bolt that threads into the first to retain it in place.
Why not wire brush the bolts to remove the gross corrosion, soak them in Coca-Cola to convert the remaining fe3 & reapply the failed few atoms thick layer of phosphorus passivation (if there ever was one), apply a bit of primer to bond to and keep the new layer protected. Then apply a decorative top coat of any color you like to seal the primer away from weather?
The job would be trivially cheap to do.
Why not wire brush the bolts to remove the gross corrosion, soak them in Coca-Cola to convert the remaining fe3 & reapply the failed few atoms thick layer of phosphorus passivation (if there ever was one), apply a bit of primer to bond to and keep the new layer protected. Then apply a decorative top coat of any color you like to seal the primer away from weather?
The job would be trivially cheap to do.
Last edited by base2; 09-30-23 at 08:04 AM.
#10
Newbie
To be certain I'd need to see the fastener out of the frame, but it looks like the exact part you need is a "Hex Drive Binding Barrel and Screw" - which you can get in stainless from McMaster-Carr: https://www.mcmaster.com/products/bu...ls-and-screws/
Just measure it well (preferably with a caliper) and you should be good to go. Be careful that it isn't just slightly too long (if they don't have the exact size of what the bike came with), or it may bear against itself rather than the frame. Some grease on the shaft and blue loctite on the threads would go a long way as well.
Just measure it well (preferably with a caliper) and you should be good to go. Be careful that it isn't just slightly too long (if they don't have the exact size of what the bike came with), or it may bear against itself rather than the frame. Some grease on the shaft and blue loctite on the threads would go a long way as well.
Last edited by poinciana; 09-30-23 at 08:29 AM.
Likes For poinciana:
#11
Droid on a mission
Join Date: May 2018
Location: Palm Coast, FL
Posts: 1,012
Bikes: Diamondback Wildwood Classic
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 320 Post(s)
Liked 285 Times
in
198 Posts
I'll wager that it is an unusual fastener type. One end is a long barrel that is the full diameter of the hole and fills the hinge from end to end for the full length. The other end is a standard bolt that threads into the first to retain it in place.
Why not wire brush the bolts to remove the gross corrosion, soak them in Coca-Cola to convert the remaining fe3 & reapply the failed few atoms thick layer of phosphorus passivation (if there ever was one), apply a bit of primer to bond to and keep the new layer protected. Then apply a decorative top coat of any color you like to seal the primer away from weather?
The job would be trivially cheap to do.
Why not wire brush the bolts to remove the gross corrosion, soak them in Coca-Cola to convert the remaining fe3 & reapply the failed few atoms thick layer of phosphorus passivation (if there ever was one), apply a bit of primer to bond to and keep the new layer protected. Then apply a decorative top coat of any color you like to seal the primer away from weather?
The job would be trivially cheap to do.
Exactly what I would do. Agree that the barrel is long, like a pivot bolt from a mountain bike suspension pivot bolt
![](https://m.media-amazon.com/images/I/71W-g8kInoL._AC_UL320_.jpg)
__________________
JoeTBM (The Bike Man) - I'm a black & white type of guy, the only gray in my life is the hair on my head
www.TheBikeMenOfFlaglerCounty.com
JoeTBM (The Bike Man) - I'm a black & white type of guy, the only gray in my life is the hair on my head
#12
I am potato.
Join Date: Jun 2015
Location: Pacific Northwest
Posts: 3,168
Bikes: Only precision built, custom high performance elitist machines of the highest caliber. 🍆
Mentioned: 30 Post(s)
Tagged: 0 Thread(s)
Quoted: 1820 Post(s)
Liked 1,695 Times
in
969 Posts
To be certain I'd need to see the fastener out of the frame, but it looks like the exact part you need is a "Hex Drive Binding Barrel and Screw" - which you can get in stainless from McMaster-Carr: https://www.mcmaster.com/products/bu...ls-and-screws/
Just measure it well (preferably with a caliper) and you should be good to go. Be careful that it isn't just slightly too long (if they don't have the exact size of what the bike came with), or it may bear against itself rather than the frame. Some grease on the shaft and blue loctite on the threads would go a long way as well.
Just measure it well (preferably with a caliper) and you should be good to go. Be careful that it isn't just slightly too long (if they don't have the exact size of what the bike came with), or it may bear against itself rather than the frame. Some grease on the shaft and blue loctite on the threads would go a long way as well.
I would think that in this particular application, a tiny fraction long so that it does bind against itself, and not the hinge would be a positive. That way the twisting of the hinge action doesn't exert a torque on the two halves relative to eachother causing it to loosen. Still, a thread retaining compound like Loctite in such a safety critical bolt is still sage advice.
__________________
I shouldn't have to "make myself more visible;" Drivers should just stop running people over.
Car dependency is a tax.
I shouldn't have to "make myself more visible;" Drivers should just stop running people over.
Car dependency is a tax.
Likes For base2:
#13
aged to perfection
Join Date: Jun 2009
Location: PacNW
Posts: 1,867
Bikes: Dinucci Allez 2.0, Richard Sachs, Alex Singer, Serotta, Masi GC, Raleigh Pro Mk.1, Hetchins, etc
Mentioned: 24 Post(s)
Tagged: 0 Thread(s)
Quoted: 857 Post(s)
Liked 1,294 Times
in
684 Posts
Right, when I saw the allen heads on both ends, it's a suspension pivot bolt, I'd bet.
pull it out, take some measurements, and go fish. I found the below with 15 seconds of searcning eboy "MTB suspension pivot bolt titanium"
this is eboy 145147162510 but there are lots of choices. 10 buck.
you will need to take the length into account. Looks like these have a threaded tube between the bolts.
and this is one application where some grease - inside and out - will work in your favor.
/markp
pull it out, take some measurements, and go fish. I found the below with 15 seconds of searcning eboy "MTB suspension pivot bolt titanium"
this is eboy 145147162510 but there are lots of choices. 10 buck.
you will need to take the length into account. Looks like these have a threaded tube between the bolts.
and this is one application where some grease - inside and out - will work in your favor.
/markp
![](https://cimg4.ibsrv.net/gimg/bikeforums.net-vbulletin/497x496/s_l1600_c82db6c06f4eddc1534ac4019d390dabda6430f1.jpg)
Last edited by mpetry912; 09-30-23 at 09:20 AM.
Likes For mpetry912:
#14
Newbie
I would think that in this particular application, a tiny fraction long so that it does bind against itself, and not the hinge would be a positive. That way the twisting of the hinge action doesn't exert a torque on the two halves relative to eachother causing it to loosen.
Of course, a washer or two would take care of that anyway, in the off chance it needed it.
#15
I'm good to go!
Join Date: Jul 2017
Location: Mississippi
Posts: 15,265
Bikes: Tarmac Disc Comp Di2 - 2020
Mentioned: 52 Post(s)
Tagged: 0 Thread(s)
Quoted: 6344 Post(s)
Liked 4,945 Times
in
3,405 Posts
I've had seat post clamp bolts like that. They were the ones I typically broke often as the threaded part is so much less diameter than the other part it threads into. Though I don't remember any bikes having one that would span that distance. However a couple other members gave you good hints on what to look for and search for on the internet.
You also might just go down to your local dealer for that bike and see if they have or can get some for you. But if you have to improvise something, stainless steel would be my preferred material. 316L if you can find it. Maybe at a marine supplier if you just decide to go with a regular bolt and nut. 304 stainless, which is the common SS you find, will in areas of salt breeze not hold up as well.
Still, if you take that out. Clean it up with a wire brush and spray with some zinc based primer will likely last a decent amount of time with a touch up every great once in a while. Just don't over torque it and break it when you put it back in.
Likes For mpetry912:
#18
Generally bewildered
Join Date: Aug 2015
Location: Eastern PA, USA
Posts: 3,038
Bikes: 2014 Trek Domane 6.9, 1999 LeMond Zurich, 1978 Schwinn Superior
Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
Quoted: 1152 Post(s)
Liked 342 Times
in
252 Posts
Thanks, Mark. I owe any knowledge in the area to a dated reference: "Carroll Smith's Nuts, Bolts, Fasteners and Plumbing Handbook", published 1990. Appreciate the update.
Likes For WizardOfBoz: