Viewing Rotor in Caliper - Rear Brake
#1
Viewing Rotor in Caliper - Rear Brake
What is the easiest way to see the rotor spin through the rear calliper: standing behind the bike, or in front of the bike; and, should the bike be tilted front wheel up, down or level?
I could easily see the front wheel, regardless if I’m standing in front of the bike or behind the bike with the bike on the stand, or just by holding up front wheel and spinning it. Without even trying, I could see the space between the pad and the calliper on both sides.
I’ve used the white paper and light both in front and behind the rear calliper but it’s tricky compared to the front. At least for me. Thanks for any help you can offer.
I could easily see the front wheel, regardless if I’m standing in front of the bike or behind the bike with the bike on the stand, or just by holding up front wheel and spinning it. Without even trying, I could see the space between the pad and the calliper on both sides.
I’ve used the white paper and light both in front and behind the rear calliper but it’s tricky compared to the front. At least for me. Thanks for any help you can offer.
#2
Generally; front wheel low, looking through the back of the caliper where the rotor enters as the wheel spins. White paper on the floor. You'll be looking in line with the pads, tangent to the rotor.
#4
Senior Member
I use a white bucket... Because I happened to have it nearby and then found I can move it around into the right position with my foot
Likes For Camilo:
#5
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,341
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Liked 4,188 Times
in
2,471 Posts
I'll shine a flashlight through the rotor and pad gaps. Andy
__________________
AndrewRStewart
AndrewRStewart
Likes For mpetry912:
#8
Likes For Kontact:
#9
Senior Member
I think he inferred that the rotor was out of true
Because that is the correct way of centering the pads and making them square to the rotor. Holding the brake lever closed does not work reliably.
Likes For Rick:
#10
+1. Depending on whether you use a plunge-style or lever-style of indicator, I'll bet you could rig a small fixture to clamp to the seatstay or chainstay, to fix in the field, although my trunk bag full of basic tools in already too heavy. Plus you'd also need the straightening tool. Or if you lack a truing stand, I have none, I always just true in the bike with something clamped to the seatstay or chainstay. Come to think of it, I ought to dig my indicator out of storage and use for truing wheels. Yes I do true them that close, take longer than the LBS, but then they stay in true forever, unless I break a spoke or bonk the rim.
Last edited by Duragrouch; 02-19-24 at 01:04 AM.
#11
Then you are either lucky or haven't noticed the problem. Once you work in a shop and adjust these things all day you see that this method doesn't produce reliable results because it hides the tendency of the calipers to twist as the mounting bolts are tightened, among other things.
#12
Senior Member
Then you are either lucky or haven't noticed the problem. Once you work in a shop and adjust these things all day you see that this method doesn't produce reliable results because it hides the tendency of the calipers to twist as the mounting bolts are tightened, among other things.
#13
I have a follow up question (I have TRP Spyre on a Salsa Fargo).
These brakes have external pad adjustment on each side. Is there a good way to set these up:
- barrel adjustment on cable
- pad adjustment
- when tightening the caliper (1/4 turn alternating between bolts)
- putting a thin shim between pad and rotor when tightening
- note: rotor’s are straight (now) and pistons moving well (cleaned the pads and calipers yesterday). I’m asking in general so when the work on this bike I know a good process to follow from step one.
Thanks (always learning!).
These brakes have external pad adjustment on each side. Is there a good way to set these up:
- barrel adjustment on cable
- pad adjustment
- when tightening the caliper (1/4 turn alternating between bolts)
- putting a thin shim between pad and rotor when tightening
- note: rotor’s are straight (now) and pistons moving well (cleaned the pads and calipers yesterday). I’m asking in general so when the work on this bike I know a good process to follow from step one.
Thanks (always learning!).
#14
Senior Member
Likes For Rick:
#15