Tire Tube Replacement Questions
#26
Senior Member
Thread Starter
Trying to smooth the edge requires going in at an oblique angle to the hole. You can't just run the file parallel to the bore. Thanks for your critique. I'm not perfect. The file might have slipped. How do you think it happened?
Last edited by RoadWearier; 04-19-24 at 03:21 PM.
#27
Senior Member
Join Date: Dec 2020
Location: Wake Forest, NC
Posts: 5,931
Bikes: 1989 Cinelli Supercorsa
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
Quoted: 3605 Post(s)
Liked 3,019 Times
in
1,825 Posts
How do I know? Why do you think I asked?
Likes For LarrySellerz:
#29
Senior Member
Thread Starter
#30
Senior Member
Join Date: Jul 2017
Location: Walnut Creek, CA
Posts: 761
Bikes: 1969 Peugeot PX10, 1992 Della Santa, Linus Roadster 8, Biria 700C ST-8
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 796 Post(s)
Liked 512 Times
in
325 Posts
I've ridden tubes with Presta valves in a Schrader drilled rim on occasion. I don't think it's a big problem. But you people can argue about anything so have at it.
Likes For Joe Bikerider:
#31
Senior Member
Thread Starter
This is definitely true. Actually I went to the LBS and asked for those Presta Valve "savers" so I could make the hole smaller. He asked me, "Why don't you just stick with Schrader valves?". Suggested strapping tape to guard the valve stems. I didn't want to bring up this monkey house of a forum. But I think I'm going to try that first. The rear stem isn't quite as bad but it is definitely cutting into the stem too. Probably tape alone will do the trick. I think the files were probably overkill. And I agree...may run the rest of enraging the hole or making it oval.
#32
Full Member
Join Date: Mar 2024
Location: San Diego
Posts: 391
Bikes: Columbine, Paramount Track Bike, Colnago Super, Santana Tandems (1995 & 2007), Gary Fisher Piranha, Trek Wahoo, Bianchi Track Bike, a couple of Honda mountain bikes
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 192 Post(s)
Liked 111 Times
in
78 Posts
This is definitely true. Actually I went to the LBS and asked for those Presta Valve "savers" so I could make the hole smaller. He asked me, "Why don't you just stick with Schrader valves?". Suggested strapping tape to guard the valve stems. I didn't want to bring up this monkey house of a forum. But I think I'm going to try that first. The rear stem isn't quite as bad but it is definitely cutting into the stem too. Probably tape alone will do the trick. I think the files were probably overkill. And I agree...may run the rest of enraging the hole or making it oval.
https://www.amazon.com/26x1-75-TR4A-...s%2C162&sr=1-8
__________________
Cheers, Mike
Cheers, Mike
Likes For PromptCritical:
#34
Senior Member
Join Date: Dec 2008
Location: Pioneer Valley
Posts: 1,228
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 400 Post(s)
Liked 931 Times
in
480 Posts
If you cleaned up the hole with a file and/or sandpaper, you should be good to go with schraeder valves. Note that if it’s a particularly narrow rim, the wider valve can get in the way of the tire bead seating properly.
#35
Expired Member
Join Date: Jun 2007
Location: TN
Posts: 11,787
Mentioned: 41 Post(s)
Tagged: 0 Thread(s)
Quoted: 3764 Post(s)
Liked 5,713 Times
in
2,882 Posts
This doesn't need to be difficult. Schrader to Presta
#36
Senior Member
Thread Starter
Hadn't thought of that. Fortunately this is a hybrid bike with wide rims. But I see how that could happen.