Saddle cover coming loose underneath?
#1
Senior Member
Thread Starter
Join Date: Mar 2005
Location: NC USA
Posts: 79
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 4 Times
in
1 Post
Saddle cover coming loose underneath?
I've got an old Vetta saddle that has it's cover coming loose on the underside edges. I want to repair this, but I'm not sure of the best way to do so. I'm assuming that I could probably just squirt some sort of glue in between the saddle base & the cover's edges, press down and hope it holds. But I'm not sure which adhesive might work best, or what to stay away from, etc.
Surely this has happened to others. Any advice or tips would be greatly appreciated.
Surely this has happened to others. Any advice or tips would be greatly appreciated.
#2
Senior Member
You need contact adhesive. Some brands are simply labled as contact adhesive. Goop is a relatively thick contact adhesive, while most are quite thin. Some come in either a bottle with a brush or in a small tube.
I'd clean both surfaces with acetone or lacquer thinner before applying the adhesive. Apply it to both surfaces and wait awhile before holding the two together (per the instructions).
I'd clean both surfaces with acetone or lacquer thinner before applying the adhesive. Apply it to both surfaces and wait awhile before holding the two together (per the instructions).
#3
Senior Member
Join Date: Mar 2008
Posts: 8,688
Mentioned: 46 Post(s)
Tagged: 0 Thread(s)
Quoted: 1074 Post(s)
Liked 295 Times
in
222 Posts
I'd use regular hot glue, I've reskinned an whole saddle using that. Some pics of it in this link: https://happymtb.org/forum/read.php/1...797#msg-785797
Sets in maybe 30 seconds, no problem holding it in place with your thumbs for the duration. A minor risk of burns, so be a bit careful.
Sets in maybe 30 seconds, no problem holding it in place with your thumbs for the duration. A minor risk of burns, so be a bit careful.
#4
Senior Member
Join Date: Oct 2002
Location: Medway, MA
Posts: 2,727
Bikes: 2011 Lynskey Sportive, 1988 Cannondale SM400
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 20 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
+1 on the contact cement. Apply a THIN coat to both sides, allow it to dry, then press the two together. This is what holds laminate countertops to the particleboard substrate. It will hold for a LONG time.
#6
Commuter
Join Date: Oct 2005
Location: Canada
Posts: 54
Bikes: Jamis Coda Comp, Kona Killuaea
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Best Stuff...
is called Barge, in yellow tube. I had the exact same issue on a Terry saddle I love, and it fixed it perfectly. I ride it year round for 3 years, and it's still perfect.
I bought mine at a shoe repair place.
I bought mine at a shoe repair place.
#7
All-round nice guy.
Join Date: May 2005
Location: Ontario Canada
Posts: 448
Bikes: Kish road bike, Seven mtb, Marinoni road and track bikes.
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I've recovered a few saddles and I was a custom leatherworker for 25 years. Use cheap contact adhesive from Walmart. If you buy a small bottle it will have a brush in its cap. Pull the loose flaps back, paint the adhesive on both surfaces, let dry to the touch and press in place. Job done; real cheap. Don't get the cement where you don't want it.
#8
Senior Member
Thread Starter
Join Date: Mar 2005
Location: NC USA
Posts: 79
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 4 Times
in
1 Post
UPDATE:
Thanks to everyone for the comments and suggestions. I obtained some contact adhesive, and that really seemed to work perfectly. Saddle is now repaired and back on the bike.
Thanks to everyone for the comments and suggestions. I obtained some contact adhesive, and that really seemed to work perfectly. Saddle is now repaired and back on the bike.