Need some help solving this
#1
Senior Member
Thread Starter
Need some help solving this
I’ve tried everything I can think of. When the chain is on the small chainring I get a grinding noise on every hard pedal stroke. No noise when I do a soft pedal stroke and no noise at all on the large chainring. Doesn’t matter what the rear cog is and I’ve moved the front derailleur up, down and sideways. I’ve also tried different pedals. Any ideas?
#2
Full Member
Join Date: Jul 2018
Location: WNY
Posts: 446
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
Quoted: 177 Post(s)
Liked 318 Times
in
164 Posts
Is the inner chainring bent at all? Sounds like deflection when working hard.
__________________
72+76 Super Course, 74 P-10+ 79 Tandem Paramounts, 84 Raleigh Alyeska, 84 Voyageur SP, 85 Miyata Sport 10 mixte and a queue
72+76 Super Course, 74 P-10+ 79 Tandem Paramounts, 84 Raleigh Alyeska, 84 Voyageur SP, 85 Miyata Sport 10 mixte and a queue
Likes For Schreck83:
#3
Semper Fi
Join Date: Jan 2008
Posts: 12,943
Mentioned: 89 Post(s)
Tagged: 0 Thread(s)
Quoted: 1172 Post(s)
Liked 358 Times
in
241 Posts
I’d check the bottom bracket bearings and cups for wear,, and the rear wheel’s bearings as well. I had issues with the pre-load on both of these bearing locations allowing them to loosen and cause grinding of surfaces due to play.
Semper Fi bro👍
Bill
Semper Fi bro👍
Bill
__________________
Semper Fi, USMC, 1975-1977
I Can Do All Things Through Him, Who Gives Me Strength. Philippians 4:13
Semper Fi, USMC, 1975-1977
I Can Do All Things Through Him, Who Gives Me Strength. Philippians 4:13
#4
Ride, Wrench, Swap, Race
Join Date: Jan 2010
Location: Northern California
Posts: 9,196
Bikes: Cheltenham-Pedersen racer, Boulder F/S Paris-Roubaix, Varsity racer, '52 Christophe, '62 Continental, '92 Merckx, '75 Limongi, '76 Presto, '72 Gitane SC, '71 Schwinn SS, etc.
Mentioned: 132 Post(s)
Tagged: 0 Thread(s)
Quoted: 1566 Post(s)
Liked 1,299 Times
in
867 Posts
A worn chainring with a new chain will produce a rumble felt and heard, which gets more intense as pedaling force increases.
You can file away the forward-facing hooks from the driving side of each tooth to eliminate the noise entirely.
A 1mm bevel to the sharpened corner atop each tooth usually prevents the chain's rollers from contacting the corners during both the engagement and disengagement events as links fall into and out of mesh with the worn chainring on every revolution.
I have fixed many chainrings this way and it's almost always the small chainring that needs it.
You can file away the forward-facing hooks from the driving side of each tooth to eliminate the noise entirely.
A 1mm bevel to the sharpened corner atop each tooth usually prevents the chain's rollers from contacting the corners during both the engagement and disengagement events as links fall into and out of mesh with the worn chainring on every revolution.
I have fixed many chainrings this way and it's almost always the small chainring that needs it.
Likes For dddd:
#5
small ring
Join Date: Jul 2012
Location: PNW
Posts: 1,027
Mentioned: 24 Post(s)
Tagged: 0 Thread(s)
Quoted: 439 Post(s)
Liked 930 Times
in
372 Posts
do I see daylight under the chain?
__________________
59 Allegro Special -- 72 Bob Jackson -- 74 Motobecane Grand Jubile -- 74 Sekine SHS 271 -- 80 Nishiki International
85 Shogun 800 -- 86 Tommasini Super Prestige -- 92 Specialized Rockhopper -- 17 Colnago Arabesque
59 Allegro Special -- 72 Bob Jackson -- 74 Motobecane Grand Jubile -- 74 Sekine SHS 271 -- 80 Nishiki International
85 Shogun 800 -- 86 Tommasini Super Prestige -- 92 Specialized Rockhopper -- 17 Colnago Arabesque
#6
Myrtle Beach Crab
Join Date: Nov 2012
Location: Newport RI
Posts: 826
Bikes: enough one would think, but thinking isn't my strong point
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 271 Post(s)
Liked 541 Times
in
214 Posts
doesn't look like the chain is evenly seated across all the chainring teeth.
#7
Senior Member
Join Date: Jun 2006
Posts: 20,305
Mentioned: 130 Post(s)
Tagged: 0 Thread(s)
Quoted: 3464 Post(s)
Liked 2,831 Times
in
1,997 Posts
for grins, check the security of the chainring bolts.
#8
Senior Member
Join Date: Nov 2014
Location: Eugene, Oregon, USA
Posts: 27,545
Mentioned: 217 Post(s)
Tagged: 0 Thread(s)
Quoted: 18399 Post(s)
Liked 4,525 Times
in
3,361 Posts
How about some good photos of the small ring?
After replacing the chain, I rotated my small ring a bolt hole or so, hoping to even out the wear, but instead I created noise problems, and I eventually replaced the ring.
After replacing the chain, I rotated my small ring a bolt hole or so, hoping to even out the wear, but instead I created noise problems, and I eventually replaced the ring.
#9
Senior Member
Thread Starter
Chainring bolts tight, chain is fitting on the ring fine.
#10
Senior Member
Join Date: Feb 2013
Location: Alta California
Posts: 14,302
Mentioned: 415 Post(s)
Tagged: 1 Thread(s)
Quoted: 3822 Post(s)
Liked 3,368 Times
in
2,197 Posts
-----
another possible contributing cause could be a torsioned chain
you could demount chain and let it hang loosely to check for a torsioned section
-----
another possible contributing cause could be a torsioned chain
you could demount chain and let it hang loosely to check for a torsioned section
-----
#11
Senior Member
Join Date: Jan 2005
Location: Baltimore, MD
Posts: 5,420
Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
Quoted: 2508 Post(s)
Liked 2,991 Times
in
1,697 Posts
Photo of back of chainrings in post 9 shows badly worn teeth on the smaller ring and moderate wear of those of the outer ring. Notice that the troughs between the teeth of the inner ring are longer and more asymmetrical than those of the outer ring.
I'd replace both rings, but you might be able to get away with replacing just the inner ring for a season or two.
I'd replace both rings, but you might be able to get away with replacing just the inner ring for a season or two.
Likes For Trakhak:
#12
Senior Member
Thread Starter
I’m going to blame it on the Regina chain. I pulled the cranks to inspect everything. Checked the bottom bracket to make sure it was tight. Then a stuck a narrower chain on it. No more noise, I’m wondering if the Regina was too wide.
#13
Banned.
Join Date: Jul 2009
Location: PAZ
Posts: 12,294
Mentioned: 255 Post(s)
Tagged: 0 Thread(s)
Quoted: 2588 Post(s)
Liked 4,827 Times
in
1,709 Posts
That particular Regina is pretty wide, and that extra width contributed - but I agree with Trakhak : the "shark tooth" profile on the inner ring teeth dictates immediate replacement.
DD
DD
#14
Senior Member
Join Date: Feb 2013
Location: Alta California
Posts: 14,302
Mentioned: 415 Post(s)
Tagged: 1 Thread(s)
Quoted: 3822 Post(s)
Liked 3,368 Times
in
2,197 Posts
-----
wrt shark tooth profile -
since the chainwheel's dentition is cut from the centre of the stock you can double its life by reversing it
the bushings will protrude one mm or so above the face of the chainwheel but all else will be the same...
-----
wrt shark tooth profile -
since the chainwheel's dentition is cut from the centre of the stock you can double its life by reversing it
the bushings will protrude one mm or so above the face of the chainwheel but all else will be the same...
-----
Last edited by juvela; 08-05-21 at 04:10 PM. Reason: spellin'
#15
Senior Member
Join Date: Jan 2016
Posts: 3,470
Mentioned: 33 Post(s)
Tagged: 0 Thread(s)
Quoted: 880 Post(s)
Liked 2,305 Times
in
1,290 Posts
I had the same symptoms with a worn out chain. I had just bought the bike and it hadn’t been ridden in quite a while . the FW was for racing so I replaced it with a more touring set up. The chain rings looked very good and I did not check the chain before I cleaned and lubed it . Every thing was cool on the stand and when I was just cruising. When I accelerated or climbed I got a grinding feeling. I had already serviced the bottom bracket . I took it apart again and meticulously cleaned and greased the bearings and put it back together with proper adjustment. Finally I gave up after 3 or 4 short rides and took it to my favorite LBS. The first thing they checked was the chain, yup! I bought a new chain AND a chain gage. Bike rode smooth as butter.
Likes For Kabuki12:
#16
Old fart
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,814
Bikes: Several, mostly not name brands.
Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3597 Post(s)
Liked 3,421 Times
in
1,946 Posts
Have you determined where it is rubbing? Hard pedaling in the small ring will cause the chainstays to deflect, which in turn can cause the chain to rub on either the front derailleur or outer ring. If it is the front derailleur that is rubbing, a little trim can fix that. If it's rubbing on the ring, that will be harder to address, and you may just have to live with it or avoid hard pedaling in the small ring.