Is a broken strand enough to warrant a replacement?
#1
Senior Member
Thread Starter
Is a broken strand enough to warrant a replacement?
I replaced the inner cable of my rear brake just a few months ago. When I unclamped the pinch bolt today to adjust the cable tension, I noticed a broken strand, seen here.
Should I replace this or just keep an eye on it and replace if more strands break?
Should I replace this or just keep an eye on it and replace if more strands break?
Last edited by djdelarosa25; 08-31-21 at 07:23 AM.
#2
Senior Member
Join Date: Dec 2019
Location: South Shore of Long Island
Posts: 2,837
Bikes: 2010 Carrera Volans, 2015 C-Dale Trail 2sl, 2017 Raleigh Rush Hour, 2017 Blue Proseccio, 1992 Giant Perigee, 80s Gitane Rallye Tandem
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
Quoted: 1110 Post(s)
Liked 1,048 Times
in
739 Posts
Actually the thing to watch for is if the strand starts to move. One strand won't matter but sometimes it starts unraveling further and curling up from the cable moving against the adjustment barrel and housing, at that point it can create excess friction and make your braking suck. But one strand isn't a big deal.
#3
Senior Member
Join Date: Dec 2010
Location: northern Deep South
Posts: 8,954
Bikes: Fuji Touring, Novara Randonee
Mentioned: 36 Post(s)
Tagged: 0 Thread(s)
Quoted: 2629 Post(s)
Liked 1,979 Times
in
1,238 Posts
At some point you'll have to replace it (as you do all cables). On the one hand, as Russ Roth notes, a single strand isn't going to make a difference (unless it starts twirling around and stabs you on the leg or hand). On the other hand, how much free time do you have and how obsessive are you about your bike? If I had a spare cable, and if I was sitting out a tropical depression's rain with nothing better to do, then I'd change the cable.
Likes For pdlamb:
#4
I'm good to go!
Join Date: Jul 2017
Location: Mississippi
Posts: 15,224
Bikes: Tarmac Disc Comp Di2 - 2020
Mentioned: 51 Post(s)
Tagged: 0 Thread(s)
Quoted: 6330 Post(s)
Liked 4,922 Times
in
3,388 Posts
In that location, I wouldn't be concerned. Though if the broken strand going up into the cable housing unravels, it might cause you some issues. But not so bad that it can't be addressed when it's a real problem for the function of your brakes.
Likely issue will be that your brakes won't open fully or fast enough after you release the brake lever. If you ever have an issue.
Likely issue will be that your brakes won't open fully or fast enough after you release the brake lever. If you ever have an issue.
Likes For Iride01:
#5
Senior Member
Join Date: Jul 2002
Location: Sacramento, California, USA
Posts: 40,865
Bikes: Specialized Tarmac, Canyon Exceed, Specialized Transition, Ellsworth Roots, Ridley Excalibur
Mentioned: 68 Post(s)
Tagged: 0 Thread(s)
Quoted: 2953 Post(s)
Liked 3,106 Times
in
1,417 Posts
I’d put a thin spot of super glue on it to keep it from unraveling.
Likes For caloso:
#6
Full Member
Join Date: Oct 2019
Location: Foothills of West Central Maine
Posts: 410
Bikes: 2007 Motobecane Fantom Cross Expert, 2020 Motobecane Omni Strada Pro Disc (700c gravel bike), 2021 Motobecane Elite Adventure with Bafang 500W rear hub drive
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 174 Post(s)
Likes: 0
Liked 144 Times
in
94 Posts
A drop of superglue might keep it from unravelling, which is a PITA.
#7
Old fart
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,840
Bikes: Several, mostly not name brands.
Mentioned: 154 Post(s)
Tagged: 0 Thread(s)
Quoted: 3617 Post(s)
Liked 3,448 Times
in
1,958 Posts
While a single broken strand may not be a problem, it begs the question of why any strand broke. If one can break, others will surely follow. Sometimes, the cable anchor on the caliper is responsible for breaking strands if it is too tight.
If it were my bike, I'd replace the cable with a new one, taking care to tighten the anchor sufficiently but not excessively. And save the old cable to be used on the front brake after trimming above the broken strand.
If it were my bike, I'd replace the cable with a new one, taking care to tighten the anchor sufficiently but not excessively. And save the old cable to be used on the front brake after trimming above the broken strand.
Likes For JohnDThompson:
#8
(rhymes with spook)
Join Date: Aug 2009
Location: Winslow, AR
Posts: 2,788
Bikes: '83 univega gran turismo x2, '85 schwinn super le tour,'89 miyata triple cross, '91 GT tequesta, '90 yokota grizzly peak, '94 GT backwoods, '95'ish scott tampico, '98 bonty privateer, '93 mongoose crossway 625, '98 parkpre ariel, 2k'ish giant fcr3
Mentioned: 26 Post(s)
Tagged: 0 Thread(s)
Quoted: 919 Post(s)
Liked 745 Times
in
546 Posts
i've fixed them with short piece of heat shrink tube. change out the cable next time you have to do the housing
Last edited by thook; 09-06-21 at 04:54 PM.
Likes For thook:
#9
Senior Member
Join Date: Jun 2013
Location: 700 Ft. above sea level.
Posts: 3,277
Bikes: More than there were awhile ago.
Mentioned: 22 Post(s)
Tagged: 0 Thread(s)
Quoted: 644 Post(s)
Liked 1,345 Times
in
629 Posts
As cheap as cables are I replace any cable with a broken or damaged strand as soon as I see it.
__________________
".....distasteful and easily triggered."
".....distasteful and easily triggered."
#10
Senior Member
Join Date: Oct 2014
Location: Portland, OR
Posts: 12,980
Bikes: (2) ti TiCycles, 2007 w/ triple and 2011 fixed, 1979 Peter Mooney, ~1983 Trek 420 now fixed and ~1973 Raleigh Carlton Competition gravel grinder
Mentioned: 131 Post(s)
Tagged: 0 Thread(s)
Quoted: 4860 Post(s)
Liked 4,005 Times
in
2,601 Posts
Rear brake? I wouldn't sweat it. I'd just make sure I had a new one on hand. (Even if this cable end goes to ****, you're going to have to cut feet off to make it a front so who cares?) And in hard stop, it's the front that's going to stop you. Now if that were my front, it would get changed out soon! Poster here have heard me talk of the "critical path" between the pavement/front tire and our hands. Failure anywhere on that path can cost us a crash, broken collarbone or far more, even death. Front brakes are right up there in importance.
#11
señor miembro
Join Date: Dec 2018
Location: Pac NW
Posts: 6,667
Bikes: '70s - '80s Campagnolo
Mentioned: 93 Post(s)
Tagged: 0 Thread(s)
Quoted: 3924 Post(s)
Liked 6,567 Times
in
3,256 Posts
HTFU, lower your quill stem, and cut your non-aero brake housing enough to trim that bit of cable.
Likes For SurferRosa:
#12
Senior Member
Join Date: Mar 2019
Posts: 1,606
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 581 Post(s)
Liked 921 Times
in
518 Posts
The only place I would ride that bike is to the bike shop to buy a new cable. It's unlikely that the cable will break, but what is very likely is that the strand will unravel a bit until the unravelling is inside the housing, and then it will affect your braking. It will also likely damage the inside of the housing - not so it is unusable, but it won't be perfect.
Changing a single inner brake cable is often very straightforward - you usually don't need to unwrap the bars or remove the housing, just cut the old cable out (so you don't have to pull a frayed end through the housing) and fish the new cable through from the lever. Sometimes it's difficult to get the end of the new cable through the hole in the brake lever and started down the first length of housing, especially if the housing isn't perfectly seated and straight in the lever, and in this case you might need to remove the handlebar tape to get it started.
Changing a single inner brake cable is often very straightforward - you usually don't need to unwrap the bars or remove the housing, just cut the old cable out (so you don't have to pull a frayed end through the housing) and fish the new cable through from the lever. Sometimes it's difficult to get the end of the new cable through the hole in the brake lever and started down the first length of housing, especially if the housing isn't perfectly seated and straight in the lever, and in this case you might need to remove the handlebar tape to get it started.
#13
Senior Member
Join Date: Feb 2017
Location: Northern Shenandoah Valley
Posts: 4,143
Bikes: More bikes than riders
Mentioned: 36 Post(s)
Tagged: 0 Thread(s)
Quoted: 1446 Post(s)
Liked 766 Times
in
572 Posts
I agree with the others that, because it's on the tensioned side of the cinch bolt, it could unravel further and even up into the housing where it could damage the liner or, as a few have already said, potentially hold the brake closed if the strand digs in. I've had several cases like that where an unraveled strand is on the non-tensioned side of the cinch bolt...where, perhaps, it started to unravel before the cable end was applied. That's usually not a problem because it can't migrate upstream beyond the cinch bolt.
#14
Senior Member
i'd let it go for a while and monitor it. When replacement time comes dont buy the same brand cable.
#15
Senior Member
I would just replace it. Cables are inexpensive enough.