Would I be foolish to drill Trek rims to fit Schraders?
#1
Junior Member
Thread Starter
Join Date: Jun 2013
Posts: 93
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 82 Post(s)
Liked 23 Times
in
19 Posts
Would I be foolish to drill Trek rims to fit Schraders?
I can't see any advantage (fill me in if I'm wrong) to using Presta valves. They leak down about the same from what I can see and still develop pin hole leaks at the stem base just like anything else.
So for me, it just presents a headache when using an air compressor or car inflator.
Would I be an idiot to drill out a 20 year old Trek's Bontrager rims?
So for me, it just presents a headache when using an air compressor or car inflator.
Would I be an idiot to drill out a 20 year old Trek's Bontrager rims?
#2
Senior Member
Join Date: Feb 2022
Location: GMT-5
Posts: 977
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 570 Post(s)
Liked 428 Times
in
283 Posts
I'd enjoy SV more if they also had that collar to stop the valve from hiding back into the rim every time I use my Park Tool INF-2.
I honestly don't think one is better than the other, I believe PV is actually necessary for thin rims, as SV holes just remove too much integrity and may make the wheel harder to keep true.
I honestly don't think one is better than the other, I believe PV is actually necessary for thin rims, as SV holes just remove too much integrity and may make the wheel harder to keep true.
Likes For soyabean:
#3
Full Member
Join Date: Mar 2013
Location: Albany, NY
Posts: 482
Bikes: Trek FX 7.3, Orbea Terra, Aostimotor S17 ebike, Huffy RedRock (first bike)
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 237 Post(s)
Liked 364 Times
in
164 Posts
Not saying I did that, but if I did it to my hybrid with pretty wide rims, I'd never tell anyone.
#4
Senior Member
Join Date: Jul 2006
Location: San Jose (Willow Glen) Ca
Posts: 9,981
Bikes: Kirk Custom JK Special, '84 Team Miyata,(dura ace old school) 80?? SR Semi-Pro 600 Arabesque
Mentioned: 107 Post(s)
Tagged: 0 Thread(s)
Quoted: 2394 Post(s)
Liked 2,950 Times
in
1,611 Posts
Lot easier to just get presta to schrader adapters
I have found presta better for on the road repairs.... and in general prefer them...but to each their own
https://www.amazon.com/s?k=presta+to...f=sr_nr_p_72_1
I have found presta better for on the road repairs.... and in general prefer them...but to each their own
https://www.amazon.com/s?k=presta+to...f=sr_nr_p_72_1
__________________
Life is too short not to ride the best bike you have, as much as you can.
Life is too short not to ride the best bike you have, as much as you can.
#5
Let your bike be the tool
Join Date: Jun 2006
Location: NC/SC border
Posts: 945
Bikes: '66 Raleigh Carlton, '70 Ron Cooper, '95 Bianchi CD'I, Zonal Frame with Xenon gruppo, Carbon Frame with Record Gruppo, Columbia Twosome, Terry Classic, Bianchi SX, Gravity SS/FG
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 342 Post(s)
Liked 317 Times
in
197 Posts
^ Beat me to it. Easier and safer to use an adapter when a Presta pump is unavailable? https://www.amazon.com/Presta-Schrader-Converter-Bicycle-Adapter
__________________
Never try to teach a pig to sing...
Never try to teach a pig to sing...
Last edited by cranky old road; 11-16-23 at 07:03 PM.
#6
señor miembro
Join Date: Dec 2018
Location: Pac NW
Posts: 6,701
Bikes: '70s - '80s Campagnolo
Mentioned: 93 Post(s)
Tagged: 0 Thread(s)
Quoted: 3939 Post(s)
Liked 6,631 Times
in
3,281 Posts
For me, presta valves are enormously easier and quicker to inflate to a specific number. Plus, they don't look like they belong to a bso from 1970.
#7
SE Wis
Join Date: Apr 2005
Location: Milwaukee, WI
Posts: 10,557
Bikes: '68 Raleigh Sprite, '02 Raleigh C500, '84 Raleigh Gran Prix, '91 Trek 400, 2013 Novara Randonee, 1990 Trek 970
Mentioned: 40 Post(s)
Tagged: 0 Thread(s)
Quoted: 2755 Post(s)
Liked 3,427 Times
in
2,075 Posts
I just keep some of these in the air tool drawer of the tool box. NO big deal to screw on.
https://www.amazon.com/Bike-Bits-Bra.../dp/B07DN2MTKQ
https://www.amazon.com/Bike-Bits-Bra.../dp/B07DN2MTKQ
Likes For dedhed:
#8
Junior Member
Depends on the width of the rim. If it's a narrow rim from a road bike, just use an adapter. Drilling the hole larger can compromise the integrity of a narrow rim if the hole is too big. However on bikes with wider rims like a MTB or a hybrid, drilled out many holes to accommodate the schrader valve without issue.
Likes For frdfandc:
#9
Really Old Senior Member
Depends on the width of the rim. If it's a narrow rim from a road bike, just use an adapter. Drilling the hole larger can compromise the integrity of a narrow rim if the hole is too big. However on bikes with wider rims like a MTB or a hybrid, drilled out many holes to accommodate the schrader valve without issue.
I just keep an adapter on my key chain.
#10
Senior Member
Join Date: May 2022
Location: USA - Southwest PA
Posts: 3,260
Bikes: Cannondale - Gary Fisher - Giant - Litespeed - Schwinn Paramount - Schwinn (lugged steel) - Trek OCLV
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 1455 Post(s)
Liked 2,059 Times
in
1,162 Posts
I use a portable inflator exclusively to inflate the tires on our bikes
except for a 60’s Schwinn Stingray - all of the bikes have presta valves
I use a thread on adapter as mentioned in above / previous posts - takes a few seconds to thread the adapter on to the presta valve and to unscrew it after the tire is inflated
except for a 60’s Schwinn Stingray - all of the bikes have presta valves
I use a thread on adapter as mentioned in above / previous posts - takes a few seconds to thread the adapter on to the presta valve and to unscrew it after the tire is inflated
Likes For t2p:
#11
Senior Member
Join Date: Dec 2004
Posts: 1,189
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 659 Post(s)
Liked 744 Times
in
439 Posts
I can't see any advantage (fill me in if I'm wrong) to using Presta valves. They leak down about the same from what I can see and still develop pin hole leaks at the stem base just like anything else.
So for me, it just presents a headache when using an air compressor or car inflator.
Would I be an idiot to drill out a 20 year old Trek's Bontrager rims?
So for me, it just presents a headache when using an air compressor or car inflator.
Would I be an idiot to drill out a 20 year old Trek's Bontrager rims?
Don't forget to debur.
Likes For CrimsonEclipse:
#12
Cantilever believer
Join Date: Nov 2021
Location: Phoenix, AZ
Posts: 1,656
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 566 Post(s)
Liked 1,958 Times
in
881 Posts
Heck, I used to drill out Rigida 1320s. Shouldn't be a problem.
As the Red Occultation said above, "don't forget to debur" - last week at Recycle Your Bicycle I had a new person drill out a pair of rims and then watched his crestfallen face as metal shavings came out the valve hole as he was inflating (fortunately, no puncture).
As the Red Occultation said above, "don't forget to debur" - last week at Recycle Your Bicycle I had a new person drill out a pair of rims and then watched his crestfallen face as metal shavings came out the valve hole as he was inflating (fortunately, no puncture).
__________________
Richard C. Moeur, PE - Phoenix AZ, USA
https://www.richardcmoeur.com/bikestuf.html
Richard C. Moeur, PE - Phoenix AZ, USA
https://www.richardcmoeur.com/bikestuf.html
Likes For RCMoeur:
#13
Junior Member
Thread Starter
Join Date: Jun 2013
Posts: 93
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 82 Post(s)
Liked 23 Times
in
19 Posts
I do have a couple of those adapters and use them when I use the 12V inflator. But I find them to be a bit of an annoyance vs my bikes with Schraders. Especially so when filling a few bikes at a time.
It doesn't help that I just bought a box of 20 Schrader tubes.
These rims are holding 32mm and 25mm tires (Trek 520 and 2120). So maybe that would be too narrow to drill. I would guess it's 1/8" or so bigger diameter.
It doesn't help that I just bought a box of 20 Schrader tubes.
These rims are holding 32mm and 25mm tires (Trek 520 and 2120). So maybe that would be too narrow to drill. I would guess it's 1/8" or so bigger diameter.
Last edited by 777funk; 11-16-23 at 08:01 PM.
#14
Happy With My Bikes
Join Date: Sep 2020
Location: Oklahoma
Posts: 2,212
Bikes: Hi-Ten bike boomers, a Trek Domane and some projects
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 887 Post(s)
Liked 2,355 Times
in
1,137 Posts
Presta stems are sexier. But I would make sure the Schrader stem is long enough before drilling the rim. The profile of some aero rims may be too deep for them.
__________________
"It is the unknown around the corner that turns my wheels." -- Heinz Stücke
"It is the unknown around the corner that turns my wheels." -- Heinz Stücke
Likes For Chuck M:
#15
Senior Member
Join Date: May 2010
Location: Bastrop Texas
Posts: 4,584
Bikes: Univega, Peu P6, Peu PR-10, Ted Williams, Peu UO-8, Peu UO-18 Mixte, Peu Dolomites
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 1009 Post(s)
Liked 1,694 Times
in
1,087 Posts
When I started ridding road bikes in the 70s all the tubular tires were Presta. I just stayed with Presta as I transitioned to other bikes and tires. I would suggest ya choose what type valve you are going to go with and then just modify, if you have to, your bikes to fit your preference.
I dont see much of a significant difference between the two, however; on tubless tiers there may be big differences.
I dont see much of a significant difference between the two, however; on tubless tiers there may be big differences.
__________________
No matter where you're at... There you are... Δf:=f(1/2)-f(-1/2)
No matter where you're at... There you are... Δf:=f(1/2)-f(-1/2)
#16
Clark W. Griswold
Join Date: Mar 2014
Location: ,location, location
Posts: 13,948
Bikes: Foundry Chilkoot Ti W/Ultegra Di2, Salsa Timberjack Ti, Cinelli Mash Work RandoCross Fun Time Machine, 1x9 XT Parts Hybrid, Co-Motion Cascadia, Specialized Langster, Phil Wood Apple VeloXS Frame (w/DA 7400), R+M Supercharger2 Rohloff, Habanero Ti 26
Mentioned: 56 Post(s)
Tagged: 0 Thread(s)
Quoted: 4505 Post(s)
Liked 4,190 Times
in
2,804 Posts
I wouldn't drill the rims, I would just use a proper pump. A bicycle pump can pump bicycle tires and if you do it with some regularity you really hardly have to pump much especially with a good quality pump. A compressor would be great for setting up a tough tubeless thing or if I am working in a shop pumping loads of tires per day but then I have the Park Inflator. If I am super desperate and my pump is dead and there is no shop around and the only thing I have is a gas station then I will use my adapter but I treat it like an emergency tool not a daily use tool and have zero problems.
People in general just need to understand the difference between a car tire and bicycle tire and it will make life so much easier.
People in general just need to understand the difference between a car tire and bicycle tire and it will make life so much easier.
Likes For veganbikes:
Likes For Jeff Neese:
#18
Junior Member
I do have a couple of those adapters and use them when I use the 12V inflator. But I find them to be a bit of an annoyance vs my bikes with Schraders. Especially so when filling a few bikes at a time.
It doesn't help that I just bought a box of 20 Schrader tubes.
These rims are holding 32mm and 25mm tires (Trek 520 and 2120). So maybe that would be too narrow to drill. I would guess it's 1/8" or so bigger diameter.
It doesn't help that I just bought a box of 20 Schrader tubes.
These rims are holding 32mm and 25mm tires (Trek 520 and 2120). So maybe that would be too narrow to drill. I would guess it's 1/8" or so bigger diameter.
#19
Insane Bicycle Mechanic
Join Date: Mar 2008
Location: other Vancouver
Posts: 9,879
Mentioned: 34 Post(s)
Tagged: 0 Thread(s)
Quoted: 816 Post(s)
Liked 766 Times
in
398 Posts
As above, you are probably OK to drill your Bontrager rims for Schraeder valves.
A friend did this on his touring bike then used Presta tubes and aluminum adapters. His reasoning was that he might need to buy a new tube at a remote gas station (or something) and he might not have a choice. A Schraeder size hole and an adapter allowed for extra flexibility.
https://www.universalcycles.com/shop...ls.php?id=7716
A friend did this on his touring bike then used Presta tubes and aluminum adapters. His reasoning was that he might need to buy a new tube at a remote gas station (or something) and he might not have a choice. A Schraeder size hole and an adapter allowed for extra flexibility.
https://www.universalcycles.com/shop...ls.php?id=7716
__________________
Jeff Wills
Comcast nuked my web page. It will return soon..
Jeff Wills
Comcast nuked my web page. It will return soon..
Likes For Jeff Wills:
#20
Happy With My Bikes
Join Date: Sep 2020
Location: Oklahoma
Posts: 2,212
Bikes: Hi-Ten bike boomers, a Trek Domane and some projects
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 887 Post(s)
Liked 2,355 Times
in
1,137 Posts
Likes For Chuck M:
#21
señor miembro
Join Date: Dec 2018
Location: Pac NW
Posts: 6,701
Bikes: '70s - '80s Campagnolo
Mentioned: 93 Post(s)
Tagged: 0 Thread(s)
Quoted: 3939 Post(s)
Liked 6,631 Times
in
3,281 Posts
But for 27", use a 5/16"?
I think I upset someone here once for recommending a 5/16" socket (instead of 8mm) on all my Campy cable anchor bolts. Probably the only time I ever use any SAE socket on my bikes. Some habits are hard to break.
I think I upset someone here once for recommending a 5/16" socket (instead of 8mm) on all my Campy cable anchor bolts. Probably the only time I ever use any SAE socket on my bikes. Some habits are hard to break.
Likes For SurferRosa:
#22
Junior Member
Thread Starter
Join Date: Jun 2013
Posts: 93
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 82 Post(s)
Liked 23 Times
in
19 Posts
I think I will go with the tighter tolerance of 5/16". Can't have that 0.002" extra with the 8mm hole. We're talking ultra precision rubber here with this batch of Chinese 27" 1-1/8" Schrader tubes.
Thanks for the recommendations everyone. Sounds like I probably don't need to stress over it too much one way or the other. I will probably drill for Schraders next time I have a flat.
Thanks for the recommendations everyone. Sounds like I probably don't need to stress over it too much one way or the other. I will probably drill for Schraders next time I have a flat.
Likes For 777funk:
#23
Senior Member
Join Date: Apr 2010
Location: Elevation 666m Edmonton Canada
Posts: 2,512
Bikes: 2013 Custom SA5w / Rohloff Tourster
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 1253 Post(s)
Liked 338 Times
in
254 Posts
I've been doing it for 25 years, for 35 mm tires. Start smaller, then you file to smoothen fit and maybe need to move the hole a hair.
It is harder to find tubes anywhere for sure. Factory brand shops only allowed to stock one brand often. And another thing is the cheap ones often come 36 mm valve, fricking useless. They assume use in steel rims or something. LOL.
+1 for Schwalbe tubes, I get them direct from their warehouse. Their 40 mm valve is ok with the threads.
I still have others that used to be 48 mm.
All my rims are Dyad. NONE have any cracks, even with 32,000 heavy miles and 2 tours.
It is harder to find tubes anywhere for sure. Factory brand shops only allowed to stock one brand often. And another thing is the cheap ones often come 36 mm valve, fricking useless. They assume use in steel rims or something. LOL.
+1 for Schwalbe tubes, I get them direct from their warehouse. Their 40 mm valve is ok with the threads.
I still have others that used to be 48 mm.
All my rims are Dyad. NONE have any cracks, even with 32,000 heavy miles and 2 tours.
Last edited by GamblerGORD53; 11-17-23 at 04:51 PM.
#24
Happy With My Bikes
Join Date: Sep 2020
Location: Oklahoma
Posts: 2,212
Bikes: Hi-Ten bike boomers, a Trek Domane and some projects
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 887 Post(s)
Liked 2,355 Times
in
1,137 Posts
I hesitated posting that lest someone take it serious and toss it as an accelerant to get this to the inevitable Presta vs. Schrader argument.
__________________
"It is the unknown around the corner that turns my wheels." -- Heinz Stücke
"It is the unknown around the corner that turns my wheels." -- Heinz Stücke
Likes For Chuck M: